Skip to content

X
x393
Commit 6f36f6d1 authored by Andrey Filippov's avatar Andrey Filippov
Browse files
Options

connecting sensor subsystem to the top module

parent d4f2714d
Expand all Hide whitespace changes
Inline Side-by-side
Showing with 566 additions and 190 deletions
includes/x393_parameters.vh
View file @ 6f36f6d1
...@@ -290,5 +290,155 @@ ...@@ -290,5 +290,155 @@
parameter MEMBRIDGE_STATUS_REG= 'h3b, parameter MEMBRIDGE_STATUS_REG= 'h3b,
parameter RSEL= 1'b1, // late/early READ commands (to adjust timing by 1 SDCLK period) parameter RSEL= 1'b1, // late/early READ commands (to adjust timing by 1 SDCLK period)
parameter WSEL= 1'b0 // late/early WRITE commands (to adjust timing by 1 SDCLK period) parameter WSEL= 1'b0, // late/early WRITE commands (to adjust timing by 1 SDCLK period)
parameter SENSOR_GROUP_ADDR = 'h400, // sensor registers base address
parameter SENSOR_BASE_INC = 'h040, // increment for sesor channel
parameter HIST_SAXI_ADDR_REL = 'h100, // histograms control addresses (16 locations) relative to SENSOR_GROUP_ADDR
parameter HIST_SAXI_MODE_ADDR_REL = 'h110, // histograms mode address (1 locatios) relative to SENSOR_GROUP_ADDR
parameter SENSI2C_STATUS_REG_BASE = 'h30, // 4 locations" x30, x32, x34, x36
parameter SENSI2C_STATUS_REG_INC = 2, // increment to the next sensor
parameter SENSI2C_STATUS_REG_REL = 0, // 4 locations" 'h30, 'h32, 'h34, 'h36
parameter SENSIO_STATUS_REG_REL = 1, // 4 locations" 'h31, 'h33, 'h35, 'h37
parameter SENSOR_NUM_HISTOGRAM= 3, // number of histogram channels
parameter HISTOGRAM_RAM_MODE = "NOBUF", // valid: "NOBUF" (32-bits, no buffering), "BUF18", "BUF32"
parameter SENS_GAMMA_NUM_CHN = 3, // number of subchannels for his sensor ports (1..4)
parameter SENS_GAMMA_BUFFER = 0, // 1 - use "shadow" table for clean switching, 0 - single table per channel
// parameters defining address map
parameter SENSOR_CTRL_RADDR = 0, // relative to SENSOR_GROUP_ADDR
parameter SENSOR_CTRL_ADDR_MASK = 'h7ff, //
// bits of the SENSOR mode register
parameter SENSOR_MODE_WIDTH = 9,
parameter SENSOR_HIST_EN_BIT = 0, // 0..3 1 - enable histogram modules, disable after processing the started frame
parameter SENSOR_HIST_NRST_BIT = 4, // 0 - immediately reset all histogram modules
parameter SENSOR_16BIT_BIT = 8, // 0 - 8 bpp mode, 1 - 16 bpp (bypass gamma). Gamma-processed data is still used for histograms
parameter SENSI2C_CTRL_RADDR = 2, // 302..'h303
parameter SENSI2C_CTRL_MASK = 'h7fe,
// sensor_i2c_io relative control register addresses
parameter SENSI2C_CTRL = 'h0,
parameter SENSI2C_STATUS = 'h1,
parameter SENS_SYNC_RADDR = 'h4,
parameter SENS_SYNC_MASK = 'h7fc,
// 2 locations reserved for control/status (if they will be needed)
parameter SENS_SYNC_MULT = 'h2, // relative register address to write number of frames to combine in one (minus 1, '0' - each farme)
parameter SENS_SYNC_LATE = 'h3, // number of lines to delay late frame sync
parameter SENS_GAMMA_RADDR = 'h38, // 'h38..'h3b was 4,
parameter SENS_GAMMA_ADDR_MASK = 'h7fc,
// sens_gamma registers
parameter SENS_GAMMA_CTRL = 'h0,
parameter SENS_GAMMA_ADDR_DATA = 'h1, // bit 20 ==1 - table address, bit 20==0 - table data (18 bits)
parameter SENS_GAMMA_HEIGHT01 = 'h2, // bits [15:0] - height minus 1 of image 0, [31:16] - height-1 of image1
parameter SENS_GAMMA_HEIGHT2 = 'h3, // bits [15:0] - height minus 1 of image 2 ( no need for image 3)
// bits of the SENS_GAMMA_CTRL mode register
parameter SENS_GAMMA_MODE_WIDTH = 5, // does not include trig
parameter SENS_GAMMA_MODE_BAYER = 0,
parameter SENS_GAMMA_MODE_PAGE = 2,
parameter SENS_GAMMA_MODE_EN = 3,
parameter SENS_GAMMA_MODE_REPET = 4,
parameter SENS_GAMMA_MODE_TRIG = 5,
parameter SENSIO_RADDR = 8, //'h308 .. 'h30c
parameter SENSIO_ADDR_MASK = 'h7f8,
// sens_parallel12 registers
parameter SENSIO_CTRL = 'h0,
// SENSIO_CTRL register bits
parameter SENS_CTRL_MRST = 0, // 1: 0
parameter SENS_CTRL_ARST = 2, // 3: 2
parameter SENS_CTRL_ARO = 4, // 5: 4
parameter SENS_CTRL_RST_MMCM = 6, // 7: 6
parameter SENS_CTRL_EXT_CLK = 8, // 9: 8
parameter SENS_CTRL_LD_DLY = 10, // 10
parameter SENS_CTRL_QUADRANTS = 12, // 17:12, enable - 20
parameter SENSIO_STATUS = 'h1,
parameter SENSIO_JTAG = 'h2,
// SENSIO_JTAG register bits
parameter SENS_JTAG_PGMEN = 8,
parameter SENS_JTAG_PROG = 6,
parameter SENS_JTAG_TCK = 4,
parameter SENS_JTAG_TMS = 2,
parameter SENS_JTAG_TDI = 0,
parameter SENSIO_WIDTH = 'h3, // 1.. 2^16, 0 - use HACT
parameter SENSIO_DELAYS = 'h4, // 'h4..'h7
// 4 of 8-bit delays per register
// sensor_i2c_io command/data write registers s (relative to SENSOR_GROUP_ADDR)
parameter SENSI2C_ABS_RADDR = 'h10, // 'h310..'h31f
parameter SENSI2C_REL_RADDR = 'h20, // 'h320..'h32f
parameter SENSI2C_ADDR_MASK = 'h7f0, // both for SENSI2C_ABS_ADDR and SENSI2C_REL_ADDR
// sens_hist registers (relative to SENSOR_GROUP_ADDR)
parameter HISTOGRAM_RADDR0 = 'h30, //
parameter HISTOGRAM_RADDR1 = 'h32, //
parameter HISTOGRAM_RADDR2 = 'h34, //
parameter HISTOGRAM_RADDR3 = 'h36, //
parameter HISTOGRAM_ADDR_MASK = 'h7fe, // for each channel
// sens_hist registers
parameter HISTOGRAM_LEFT_TOP = 'h0,
parameter HISTOGRAM_WIDTH_HEIGHT = 'h1, // 1.. 2^16, 0 - use HACT
//sensor_i2c_io other parameters
parameter integer SENSI2C_DRIVE= 12,
parameter SENSI2C_IBUF_LOW_PWR= "TRUE",
parameter SENSI2C_IOSTANDARD = "DEFAULT",
parameter SENSI2C_SLEW = "SLOW",
//sensor_fifo parameters
parameter SENSOR_DATA_WIDTH = 12,
parameter SENSOR_FIFO_2DEPTH = 4,
parameter SENSOR_FIFO_DELAY = 7,
// other parameters for histogram_saxi module
parameter HIST_SAXI_ADDR_MASK = 'h7f0,
parameter HIST_SAXI_MODE_WIDTH = 8,
parameter HIST_SAXI_EN = 0,
parameter HIST_SAXI_NRESET = 1,
parameter HIST_CONFIRM_WRITE = 2, // wait write confirmation for each block
parameter HIST_SAXI_AWCACHE = 4'h3, //..7 cache mode (4 bits, default 4'h3)
parameter HIST_SAXI_MODE_ADDR_MASK = 'h7ff,
parameter NUM_FRAME_BITS = 4, // number of bits use for frame number
// Other parameters
parameter SENS_SYNC_FBITS = 16, // number of bits in a frame counter for linescan mode
parameter SENS_SYNC_LBITS = 16, // number of bits in a line counter for sof_late output (limited by eof)
parameter SENS_SYNC_LATE_DFLT = 15, // number of lines to delay late frame sync
parameter SENS_SYNC_MINBITS = 8, // number of bits to enforce minimal frame period
parameter SENS_SYNC_MINPER = 130, // minimal frame period (in pclk/mclk?)
// sens_parallel12 other parameters
// parameter IODELAY_GRP ="IODELAY_SENSOR", // may need different for different channels?
parameter integer IDELAY_VALUE = 0,
parameter integer PXD_DRIVE = 12,
parameter PXD_IBUF_LOW_PWR = "TRUE",
parameter PXD_IOSTANDARD = "DEFAULT",
parameter PXD_SLEW = "SLOW",
parameter real SENS_REFCLK_FREQUENCY = 300.0,
parameter SENS_HIGH_PERFORMANCE_MODE = "FALSE",
parameter SENS_PHASE_WIDTH= 8, // number of bits for te phase counter (depends on divisors)
parameter SENS_PCLK_PERIOD = 10.000, // input period in ns, 0..100.000 - MANDATORY, resolution down to 1 ps
parameter SENS_BANDWIDTH = "OPTIMIZED", //"OPTIMIZED", "HIGH","LOW"
parameter CLKFBOUT_MULT_SENSOR = 8, // 100 MHz --> 800 MHz
parameter CLKFBOUT_PHASE_SENSOR = 0.000, // CLOCK FEEDBACK phase in degrees (3 significant digits, -360.000...+360.000)
parameter IPCLK_PHASE = 0.000,
parameter IPCLK2X_PHASE = 0.000,
parameter SENS_DIVCLK_DIVIDE = 1, // Integer 1..106. Divides all outputs with respect to CLKIN
parameter SENS_REF_JITTER1 = 0.010, // Expectet jitter on CLKIN1 (0.000..0.999)
parameter SENS_REF_JITTER2 = 0.010,
parameter SENS_SS_EN = "FALSE", // Enables Spread Spectrum mode
parameter SENS_SS_MODE = "CENTER_HIGH",//"CENTER_HIGH","CENTER_LOW","DOWN_HIGH","DOWN_LOW"
parameter SENS_SS_MOD_PERIOD = 10000 // integer 4000-40000 - SS modulation period in ns
\ No newline at end of file
memctrl/mcntrl393.v
View file @ 6f36f6d1
...@@ -220,6 +220,7 @@ module mcntrl393 #( ...@@ -220,6 +220,7 @@ module mcntrl393 #(
input rst_in, input rst_in,
input clk_in, input clk_in,
output mclk, // global clock, half DDR3 clock, synchronizes all I/O through the command port output mclk, // global clock, half DDR3 clock, synchronizes all I/O through the command port
output ref_clk, // global clock for idelay_ctrl calibration
// programming interface // programming interface
input [7:0] cmd_ad, // byte-serial command address/data (up to 6 bytes: AL-AH-D0-D1-D2-D3 input [7:0] cmd_ad, // byte-serial command address/data (up to 6 bytes: AL-AH-D0-D1-D2-D3
input cmd_stb, // strobe (with first byte) for the command a/d input cmd_stb, // strobe (with first byte) for the command a/d
...@@ -1466,6 +1467,7 @@ module mcntrl393 #( ...@@ -1466,6 +1467,7 @@ module mcntrl393 #(
.rst_in (rst_in), // input .rst_in (rst_in), // input
.clk_in (clk_in), // input .clk_in (clk_in), // input
.mclk (mclk), // output .mclk (mclk), // output
.ref_clk (ref_clk), // output
.cmd_ad (cmd_mcontr_ad), // input[7:0] .cmd_ad (cmd_mcontr_ad), // input[7:0]
.cmd_stb (cmd_mcontr_stb), // input .cmd_stb (cmd_mcontr_stb), // input
.status_ad (status_mcontr_ad[7:0]), // output[7:0] .status_ad (status_mcontr_ad[7:0]), // output[7:0]
......
memctrl/memctrl16.v
View file @ 6f36f6d1
...@@ -141,6 +141,7 @@ module memctrl16 #( ...@@ -141,6 +141,7 @@ module memctrl16 #(
input rst_in, input rst_in,
input clk_in, input clk_in,
output mclk, // global clock, half DDR3 clock, synchronizes all I/O through the command port output mclk, // global clock, half DDR3 clock, synchronizes all I/O through the command port
output ref_clk, // global clock for idelay_ctrl calibration
// programming interface // programming interface
input [7:0] cmd_ad, // byte-serial command address/data (up to 6 bytes: AL-AH-D0-D1-D2-D3 input [7:0] cmd_ad, // byte-serial command address/data (up to 6 bytes: AL-AH-D0-D1-D2-D3
input cmd_stb, // strobe (with first byte) for the command a/d input cmd_stb, // strobe (with first byte) for the command a/d
...@@ -913,6 +914,7 @@ end ...@@ -913,6 +914,7 @@ end
.clk_in (clk_in), // axi_aclk), // input .clk_in (clk_in), // axi_aclk), // input
.rst_in (rst_in), // axi_rst), // input TODO: move buffer outside? .rst_in (rst_in), // axi_rst), // input TODO: move buffer outside?
.mclk (mclk), // output .mclk (mclk), // output
.ref_clk (ref_clk), // output
.cmd0_clk (cmd0_clk), // input .cmd0_clk (cmd0_clk), // input
.cmd0_we (cmd0_we), // input .cmd0_we (cmd0_we), // input
......
memctrl/phy/mcontr_sequencer.v
View file @ 6f36f6d1
...@@ -115,6 +115,7 @@ module mcontr_sequencer #( ...@@ -115,6 +115,7 @@ module mcontr_sequencer #(
input clk_in, input clk_in,
input rst_in, input rst_in,
output mclk, // global clock, half DDR3 clock, synchronizes all I/O through the command port output mclk, // global clock, half DDR3 clock, synchronizes all I/O through the command port
output ref_clk, // global clock for idelay_ctrl calibration
// command port 0 (filled by software - 32w->32r) - used for mode set, refresh, write levelling, ... // command port 0 (filled by software - 32w->32r) - used for mode set, refresh, write levelling, ...
input cmd0_clk, input cmd0_clk,
input cmd0_we, input cmd0_we,
...@@ -581,6 +582,7 @@ module mcontr_sequencer #( ...@@ -581,6 +582,7 @@ module mcontr_sequencer #(
.clk_in (clk_in), // input .clk_in (clk_in), // input
.rst_in (rst_in), // input .rst_in (rst_in), // input
.mclk (mclk), // output .mclk (mclk), // output
.ref_clk (ref_clk), // output
.dly_data (dly_data[7:0]), // input[7:0] .dly_data (dly_data[7:0]), // input[7:0]
.dly_addr (dly_addr[6:0]), // input[6:0] .dly_addr (dly_addr[6:0]), // input[6:0]
.ld_delay (ld_delay), // input .ld_delay (ld_delay), // input
......
memctrl/phy/phy_cmd.v
View file @ 6f36f6d1
...@@ -71,6 +71,7 @@ module phy_cmd#( ...@@ -71,6 +71,7 @@ module phy_cmd#(
input clk_in, input clk_in,
input rst_in, input rst_in,
output mclk, // global clock, half DDR3 clock, synchronizes all I/O through the command port output mclk, // global clock, half DDR3 clock, synchronizes all I/O through the command port
output ref_clk, // global clock for idelay_ctrl calibration
// inteface to control I/O delays and mmcm // inteface to control I/O delays and mmcm
input [7:0] dly_data, // delay value (3 LSB - fine delay) input [7:0] dly_data, // delay value (3 LSB - fine delay)
input [6:0] dly_addr, // select which delay to program input [6:0] dly_addr, // select which delay to program
...@@ -426,6 +427,7 @@ module phy_cmd#( ...@@ -426,6 +427,7 @@ module phy_cmd#(
.clk (), // output .clk (), // output
.clk_div (clk_div), // output .clk_div (clk_div), // output
.mclk (mclk), // output .mclk (mclk), // output
.ref_clk (ref_clk), // output
.rst_in (rst_in), // input .rst_in (rst_in), // input
.ddr_rst (ddr_rst), // input .ddr_rst (ddr_rst), // input
......
memctrl/phy/phy_top.v
View file @ 6f36f6d1
...@@ -75,6 +75,7 @@ module phy_top #( ...@@ -75,6 +75,7 @@ module phy_top #(
output clk, // free-running system clock, same frequency as iclk (shared for R/W), BUFR output output clk, // free-running system clock, same frequency as iclk (shared for R/W), BUFR output
output clk_div, // free-running half clk frequency, front aligned to clk (shared for R/W), BUFR output output clk_div, // free-running half clk frequency, front aligned to clk (shared for R/W), BUFR output
output mclk, // same as clk_div, through separate BUFG and static phase adjust output mclk, // same as clk_div, through separate BUFG and static phase adjust
output ref_clk, // global clock for idelay_ctrl calibration
input rst_in, // reset delays/serdes input rst_in, // reset delays/serdes
input ddr_rst, // active high - generate NRST to memory input ddr_rst, // active high - generate NRST to memory
input dci_rst, // active high - reset DCI circuitry input dci_rst, // active high - reset DCI circuitry
...@@ -126,7 +127,7 @@ module phy_top #( ...@@ -126,7 +127,7 @@ module phy_top #(
wire ld_cmda = (dly_addr[6:5] == 2'h2) && ld_delay ; wire ld_cmda = (dly_addr[6:5] == 2'h2) && ld_delay ;
wire ld_mmcm= (dly_addr[6:0] == 7'h60) && ld_delay ; wire ld_mmcm= (dly_addr[6:0] == 7'h60) && ld_delay ;
wire clkfb_ref, clk_ref_pre; wire clkfb_ref, clk_ref_pre;
wire clk_ref; // 200MHz/300Mhz to calibrate I/O delays // wire ref_clk; // 200MHz/300Mhz to calibrate I/O delays
// wire locked_mmcm,locked_pll, dly_ready, dci_ready; // wire locked_mmcm,locked_pll, dly_ready, dci_ready;
// assign locked=locked_mmcm && locked_pll && dly_ready && dci_ready; // both PLL ready, I/O delay calibrated // assign locked=locked_mmcm && locked_pll && dly_ready && dci_ready; // both PLL ready, I/O delay calibrated
wire clkin_stopped_mmcm; wire clkin_stopped_mmcm;
...@@ -290,10 +291,10 @@ wire clk_pre, clk_div_pre, sdclk_pre, mclk_pre, clk_fb; ...@@ -290,10 +291,10 @@ wire clk_pre, clk_div_pre, sdclk_pre, mclk_pre, clk_fb;
BUFR clk_bufr_i (.O(clk), .CE(), .CLR(), .I(clk_pre)); BUFR clk_bufr_i (.O(clk), .CE(), .CLR(), .I(clk_pre));
BUFR clk_div_bufr_i (.O(clk_div), .CE(), .CLR(), .I(clk_div_pre)); BUFR clk_div_bufr_i (.O(clk_div), .CE(), .CLR(), .I(clk_div_pre));
BUFIO iclk_bufio_i (.O(sdclk), .I(sdclk_pre) ); BUFIO iclk_bufio_i (.O(sdclk), .I(sdclk_pre) );
//BUFIO clk_ref_i (.O(clk_ref), .I(clk_ref_pre)); //BUFIO clk_ref_i (.O(ref_clk), .I(clk_ref_pre));
//assign clk_ref=clk_ref_pre; //assign ref_clk=clk_ref_pre;
//BUFH clk_ref_i (.O(clk_ref), .I(clk_ref_pre)); //BUFH clk_ref_i (.O(ref_clk), .I(clk_ref_pre));
BUFG clk_ref_i (.O(clk_ref), .I(clk_ref_pre)); BUFG clk_ref_i (.O(ref_clk), .I(clk_ref_pre));
BUFG mclk_i (.O(mclk),.I(mclk_pre) ); BUFG mclk_i (.O(mclk),.I(mclk_pre) );
mmcm_phase_cntr #( mmcm_phase_cntr #(
.PHASE_WIDTH (PHASE_WIDTH), .PHASE_WIDTH (PHASE_WIDTH),
...@@ -390,7 +391,7 @@ BUFG mclk_i (.O(mclk),.I(mclk_pre) ); ...@@ -390,7 +391,7 @@ BUFG mclk_i (.O(mclk),.I(mclk_pre) );
idelay_ctrl# ( idelay_ctrl# (
.IODELAY_GRP("IODELAY_MEMORY") .IODELAY_GRP("IODELAY_MEMORY")
) idelay_ctrl_i ( ) idelay_ctrl_i (
.refclk(clk_ref), .refclk(ref_clk),
.rst(rst || dly_rst), .rst(rst || dly_rst),
.rdy(dly_ready) .rdy(dly_ready)
); );
......
sensor/sens_parallel12.v
View file @ 6f36f6d1
...@@ -52,25 +52,25 @@ module sens_parallel12 #( ...@@ -52,25 +52,25 @@ module sens_parallel12 #(
parameter PXD_IBUF_LOW_PWR = "TRUE", parameter PXD_IBUF_LOW_PWR = "TRUE",
parameter PXD_IOSTANDARD = "DEFAULT", parameter PXD_IOSTANDARD = "DEFAULT",
parameter PXD_SLEW = "SLOW", parameter PXD_SLEW = "SLOW",
parameter real REFCLK_FREQUENCY = 300.0, parameter real SENS_REFCLK_FREQUENCY = 300.0,
parameter HIGH_PERFORMANCE_MODE = "FALSE", parameter SENS_HIGH_PERFORMANCE_MODE = "FALSE",
parameter PHASE_WIDTH= 8, // number of bits for te phase counter (depends on divisors) parameter SENS_PHASE_WIDTH= 8, // number of bits for te phase counter (depends on divisors)
parameter PCLK_PERIOD = 10.000, // input period in ns, 0..100.000 - MANDATORY, resolution down to 1 ps parameter SENS_PCLK_PERIOD = 10.000, // input period in ns, 0..100.000 - MANDATORY, resolution down to 1 ps
parameter BANDWIDTH = "OPTIMIZED", //"OPTIMIZED", "HIGH","LOW" parameter SENS_BANDWIDTH = "OPTIMIZED", //"OPTIMIZED", "HIGH","LOW"
parameter CLKFBOUT_MULT_SENSOR = 8, // 100 MHz --> 800 MHz parameter CLKFBOUT_MULT_SENSOR = 8, // 100 MHz --> 800 MHz
parameter CLKFBOUT_PHASE_SENSOR = 0.000, // CLOCK FEEDBACK phase in degrees (3 significant digits, -360.000...+360.000) parameter CLKFBOUT_PHASE_SENSOR = 0.000, // CLOCK FEEDBACK phase in degrees (3 significant digits, -360.000...+360.000)
parameter IPCLK_PHASE = 0.000, parameter IPCLK_PHASE = 0.000,
parameter IPCLK2X_PHASE = 0.000, parameter IPCLK2X_PHASE = 0.000,
parameter DIVCLK_DIVIDE = 1, // Integer 1..106. Divides all outputs with respect to CLKIN parameter SENS_DIVCLK_DIVIDE = 1, // Integer 1..106. Divides all outputs with respect to CLKIN
parameter REF_JITTER1 = 0.010, // Expectet jitter on CLKIN1 (0.000..0.999) parameter SENS_REF_JITTER1 = 0.010, // Expectet jitter on CLKIN1 (0.000..0.999)
parameter REF_JITTER2 = 0.010, parameter SENS_REF_JITTER2 = 0.010,
parameter SS_EN = "FALSE", // Enables Spread Spectrum mode parameter SENS_SS_EN = "FALSE", // Enables Spread Spectrum mode
parameter SS_MODE = "CENTER_HIGH",//"CENTER_HIGH","CENTER_LOW","DOWN_HIGH","DOWN_LOW" parameter SENS_SS_MODE = "CENTER_HIGH",//"CENTER_HIGH","CENTER_LOW","DOWN_HIGH","DOWN_LOW"
parameter SS_MOD_PERIOD = 10000 // integer 4000-40000 - SS modulation period in ns parameter SENS_SS_MOD_PERIOD = 10000 // integer 4000-40000 - SS modulation period in ns
)( )(
input rst, input rst,
...@@ -328,8 +328,8 @@ module sens_parallel12 #( ...@@ -328,8 +328,8 @@ module sens_parallel12 #(
.PXD_IBUF_LOW_PWR (PXD_IBUF_LOW_PWR), .PXD_IBUF_LOW_PWR (PXD_IBUF_LOW_PWR),
.PXD_IOSTANDARD (PXD_IOSTANDARD), .PXD_IOSTANDARD (PXD_IOSTANDARD),
.PXD_SLEW (PXD_SLEW), .PXD_SLEW (PXD_SLEW),
.REFCLK_FREQUENCY (REFCLK_FREQUENCY), .REFCLK_FREQUENCY (SENS_REFCLK_FREQUENCY),
.HIGH_PERFORMANCE_MODE (HIGH_PERFORMANCE_MODE) .HIGH_PERFORMANCE_MODE (SENS_HIGH_PERFORMANCE_MODE)
) pxd_pxd0_i ( ) pxd_pxd0_i (
.pxd (pxd[0]), // inout .pxd (pxd[0]), // inout
.pxd_out (xfpgatdi), // input .pxd_out (xfpgatdi), // input
...@@ -353,8 +353,8 @@ module sens_parallel12 #( ...@@ -353,8 +353,8 @@ module sens_parallel12 #(
.PXD_IBUF_LOW_PWR (PXD_IBUF_LOW_PWR), .PXD_IBUF_LOW_PWR (PXD_IBUF_LOW_PWR),
.PXD_IOSTANDARD (PXD_IOSTANDARD), .PXD_IOSTANDARD (PXD_IOSTANDARD),
.PXD_SLEW (PXD_SLEW), .PXD_SLEW (PXD_SLEW),
.REFCLK_FREQUENCY (REFCLK_FREQUENCY), .REFCLK_FREQUENCY (SENS_REFCLK_FREQUENCY),
.HIGH_PERFORMANCE_MODE (HIGH_PERFORMANCE_MODE) .HIGH_PERFORMANCE_MODE (SENS_HIGH_PERFORMANCE_MODE)
) pxd_pxd1_i ( ) pxd_pxd1_i (
.pxd (pxd[1]), // inout .pxd (pxd[1]), // inout
.pxd_out (1'b0), // input .pxd_out (1'b0), // input
...@@ -381,8 +381,8 @@ module sens_parallel12 #( ...@@ -381,8 +381,8 @@ module sens_parallel12 #(
.PXD_IBUF_LOW_PWR (PXD_IBUF_LOW_PWR), .PXD_IBUF_LOW_PWR (PXD_IBUF_LOW_PWR),
.PXD_IOSTANDARD (PXD_IOSTANDARD), .PXD_IOSTANDARD (PXD_IOSTANDARD),
.PXD_SLEW (PXD_SLEW), .PXD_SLEW (PXD_SLEW),
.REFCLK_FREQUENCY (REFCLK_FREQUENCY), .REFCLK_FREQUENCY (SENS_REFCLK_FREQUENCY),
.HIGH_PERFORMANCE_MODE (HIGH_PERFORMANCE_MODE) .HIGH_PERFORMANCE_MODE (SENS_HIGH_PERFORMANCE_MODE)
) pxd_pxd1_i ( ) pxd_pxd1_i (
.pxd (pxd[i]), // inout .pxd (pxd[i]), // inout
.pxd_out (1'b0), // input .pxd_out (1'b0), // input
...@@ -408,8 +408,8 @@ module sens_parallel12 #( ...@@ -408,8 +408,8 @@ module sens_parallel12 #(
.PXD_IBUF_LOW_PWR (PXD_IBUF_LOW_PWR), .PXD_IBUF_LOW_PWR (PXD_IBUF_LOW_PWR),
.PXD_IOSTANDARD (PXD_IOSTANDARD), .PXD_IOSTANDARD (PXD_IOSTANDARD),
.PXD_SLEW (PXD_SLEW), .PXD_SLEW (PXD_SLEW),
.REFCLK_FREQUENCY (REFCLK_FREQUENCY), .REFCLK_FREQUENCY (SENS_REFCLK_FREQUENCY),
.HIGH_PERFORMANCE_MODE (HIGH_PERFORMANCE_MODE) .HIGH_PERFORMANCE_MODE (SENS_HIGH_PERFORMANCE_MODE)
) pxd_hact_i ( ) pxd_hact_i (
.pxd (hact), // inout .pxd (hact), // inout
.pxd_out (1'b0), // input .pxd_out (1'b0), // input
...@@ -433,8 +433,8 @@ module sens_parallel12 #( ...@@ -433,8 +433,8 @@ module sens_parallel12 #(
.PXD_IBUF_LOW_PWR (PXD_IBUF_LOW_PWR), .PXD_IBUF_LOW_PWR (PXD_IBUF_LOW_PWR),
.PXD_IOSTANDARD (PXD_IOSTANDARD), .PXD_IOSTANDARD (PXD_IOSTANDARD),
.PXD_SLEW (PXD_SLEW), .PXD_SLEW (PXD_SLEW),
.REFCLK_FREQUENCY (REFCLK_FREQUENCY), .REFCLK_FREQUENCY (SENS_REFCLK_FREQUENCY),
.HIGH_PERFORMANCE_MODE (HIGH_PERFORMANCE_MODE) .HIGH_PERFORMANCE_MODE (SENS_HIGH_PERFORMANCE_MODE)
) pxd_vact_i ( ) pxd_vact_i (
.pxd (vact), // inout .pxd (vact), // inout
.pxd_out (1'b0), // input .pxd_out (1'b0), // input
...@@ -458,8 +458,8 @@ module sens_parallel12 #( ...@@ -458,8 +458,8 @@ module sens_parallel12 #(
.PXD_IBUF_LOW_PWR (PXD_IBUF_LOW_PWR), .PXD_IBUF_LOW_PWR (PXD_IBUF_LOW_PWR),
.PXD_IOSTANDARD (PXD_IOSTANDARD), .PXD_IOSTANDARD (PXD_IOSTANDARD),
.PXD_SLEW (PXD_SLEW), .PXD_SLEW (PXD_SLEW),
.REFCLK_FREQUENCY (REFCLK_FREQUENCY), .REFCLK_FREQUENCY (SENS_REFCLK_FREQUENCY),
.HIGH_PERFORMANCE_MODE (HIGH_PERFORMANCE_MODE) .HIGH_PERFORMANCE_MODE (SENS_HIGH_PERFORMANCE_MODE)
) pxd_clock_i ( ) pxd_clock_i (
.pxclk (bpf), // inout .pxclk (bpf), // inout
.pxclk_out (1'b0), // input .pxclk_out (1'b0), // input
...@@ -555,11 +555,11 @@ module sens_parallel12 #( ...@@ -555,11 +555,11 @@ module sens_parallel12 #(
// generate phase-shifterd pixel clock (and 2x version) from either the internal clock (that is output to the sensor) or from the clock // generate phase-shifterd pixel clock (and 2x version) from either the internal clock (that is output to the sensor) or from the clock
// received from the sensor (may need to reset MMCM after resetting sensor) // received from the sensor (may need to reset MMCM after resetting sensor)
mmcm_phase_cntr #( mmcm_phase_cntr #(
.PHASE_WIDTH (PHASE_WIDTH), .PHASE_WIDTH (SENS_PHASE_WIDTH),
.CLKIN_PERIOD (PCLK_PERIOD), .CLKIN_PERIOD (SENS_PCLK_PERIOD),
.BANDWIDTH (BANDWIDTH), .BANDWIDTH (SENS_BANDWIDTH),
.CLKFBOUT_MULT_F (CLKFBOUT_MULT_SENSOR), //8 .CLKFBOUT_MULT_F (CLKFBOUT_MULT_SENSOR), //8
.DIVCLK_DIVIDE (DIVCLK_DIVIDE), .DIVCLK_DIVIDE (SENS_DIVCLK_DIVIDE),
.CLKFBOUT_PHASE (CLKFBOUT_PHASE_SENSOR), .CLKFBOUT_PHASE (CLKFBOUT_PHASE_SENSOR),
.CLKOUT0_PHASE (IPCLK_PHASE), .CLKOUT0_PHASE (IPCLK_PHASE),
.CLKOUT1_PHASE (IPCLK2X_PHASE), .CLKOUT1_PHASE (IPCLK2X_PHASE),
...@@ -584,11 +584,11 @@ module sens_parallel12 #( ...@@ -584,11 +584,11 @@ module sens_parallel12 #(
// .CLKOUT5_DIVIDE(1), // .CLKOUT5_DIVIDE(1),
// .CLKOUT6_DIVIDE(1), // .CLKOUT6_DIVIDE(1),
.COMPENSATION ("ZHOLD"), .COMPENSATION ("ZHOLD"),
.REF_JITTER1 (REF_JITTER1), .REF_JITTER1 (SENS_REF_JITTER1),
.REF_JITTER2 (REF_JITTER2), .REF_JITTER2 (SENS_REF_JITTER2),
.SS_EN (SS_EN), .SS_EN (SENS_SS_EN),
.SS_MODE (SS_MODE), .SS_MODE (SENS_SS_MODE),
.SS_MOD_PERIOD (SS_MOD_PERIOD), .SS_MOD_PERIOD (SENS_SS_MOD_PERIOD),
.STARTUP_WAIT ("FALSE") .STARTUP_WAIT ("FALSE")
) mmcm_phase_cntr_i ( ) mmcm_phase_cntr_i (
.clkin1 (pclk), // input .clkin1 (pclk), // input
......
sensor/sensor_channel.v
View file @ 6f36f6d1
...@@ -135,25 +135,25 @@ module sensor_channel#( ...@@ -135,25 +135,25 @@ module sensor_channel#(
parameter PXD_IBUF_LOW_PWR = "TRUE", parameter PXD_IBUF_LOW_PWR = "TRUE",
parameter PXD_IOSTANDARD = "DEFAULT", parameter PXD_IOSTANDARD = "DEFAULT",
parameter PXD_SLEW = "SLOW", parameter PXD_SLEW = "SLOW",
parameter real REFCLK_FREQUENCY = 300.0, parameter real SENS_REFCLK_FREQUENCY = 300.0,
parameter HIGH_PERFORMANCE_MODE = "FALSE", parameter SENS_HIGH_PERFORMANCE_MODE = "FALSE",
parameter PHASE_WIDTH= 8, // number of bits for te phase counter (depends on divisors) parameter SENS_PHASE_WIDTH= 8, // number of bits for te phase counter (depends on divisors)
parameter PCLK_PERIOD = 10.000, // input period in ns, 0..100.000 - MANDATORY, resolution down to 1 ps parameter SENS_PCLK_PERIOD = 10.000, // input period in ns, 0..100.000 - MANDATORY, resolution down to 1 ps
parameter BANDWIDTH = "OPTIMIZED", //"OPTIMIZED", "HIGH","LOW" parameter SENS_BANDWIDTH = "OPTIMIZED", //"OPTIMIZED", "HIGH","LOW"
parameter CLKFBOUT_MULT_SENSOR = 8, // 100 MHz --> 800 MHz parameter CLKFBOUT_MULT_SENSOR = 8, // 100 MHz --> 800 MHz
parameter CLKFBOUT_PHASE_SENSOR = 0.000, // CLOCK FEEDBACK phase in degrees (3 significant digits, -360.000...+360.000) parameter CLKFBOUT_PHASE_SENSOR = 0.000, // CLOCK FEEDBACK phase in degrees (3 significant digits, -360.000...+360.000)
parameter IPCLK_PHASE = 0.000, parameter IPCLK_PHASE = 0.000,
parameter IPCLK2X_PHASE = 0.000, parameter IPCLK2X_PHASE = 0.000,
parameter DIVCLK_DIVIDE = 1, // Integer 1..106. Divides all outputs with respect to CLKIN parameter SENS_DIVCLK_DIVIDE = 1, // Integer 1..106. Divides all outputs with respect to CLKIN
parameter REF_JITTER1 = 0.010, // Expectet jitter on CLKIN1 (0.000..0.999) parameter SENS_REF_JITTER1 = 0.010, // Expectet jitter on CLKIN1 (0.000..0.999)
parameter REF_JITTER2 = 0.010, parameter SENS_REF_JITTER2 = 0.010,
parameter SS_EN = "FALSE", // Enables Spread Spectrum mode parameter SENS_SS_EN = "FALSE", // Enables Spread Spectrum mode
parameter SS_MODE = "CENTER_HIGH",//"CENTER_HIGH","CENTER_LOW","DOWN_HIGH","DOWN_LOW" parameter SENS_SS_MODE = "CENTER_HIGH",//"CENTER_HIGH","CENTER_LOW","DOWN_HIGH","DOWN_LOW"
parameter SS_MOD_PERIOD = 10000 // integer 4000-40000 - SS modulation period in ns parameter SENS_SS_MOD_PERIOD = 10000 // integer 4000-40000 - SS modulation period in ns
) ( ) (
input rst, input rst,
...@@ -402,21 +402,21 @@ module sensor_channel#( ...@@ -402,21 +402,21 @@ module sensor_channel#(
.PXD_IBUF_LOW_PWR (PXD_IBUF_LOW_PWR), .PXD_IBUF_LOW_PWR (PXD_IBUF_LOW_PWR),
.PXD_IOSTANDARD (PXD_IOSTANDARD), .PXD_IOSTANDARD (PXD_IOSTANDARD),
.PXD_SLEW (PXD_SLEW), .PXD_SLEW (PXD_SLEW),
.REFCLK_FREQUENCY (REFCLK_FREQUENCY), .SENS_REFCLK_FREQUENCY (SENS_REFCLK_FREQUENCY),
.HIGH_PERFORMANCE_MODE (HIGH_PERFORMANCE_MODE), .SENS_HIGH_PERFORMANCE_MODE (SENS_HIGH_PERFORMANCE_MODE),
.PHASE_WIDTH (PHASE_WIDTH), .SENS_PHASE_WIDTH (SENS_PHASE_WIDTH),
.PCLK_PERIOD (PCLK_PERIOD), .SENS_PCLK_PERIOD (SENS_PCLK_PERIOD),
.BANDWIDTH (BANDWIDTH), .SENS_BANDWIDTH (SENS_BANDWIDTH),
.CLKFBOUT_MULT_SENSOR (CLKFBOUT_MULT_SENSOR), .CLKFBOUT_MULT_SENSOR (CLKFBOUT_MULT_SENSOR),
.CLKFBOUT_PHASE_SENSOR (CLKFBOUT_PHASE_SENSOR), .CLKFBOUT_PHASE_SENSOR (CLKFBOUT_PHASE_SENSOR),
.IPCLK_PHASE (IPCLK_PHASE), .IPCLK_PHASE (IPCLK_PHASE),
.IPCLK2X_PHASE (IPCLK2X_PHASE), .IPCLK2X_PHASE (IPCLK2X_PHASE),
.DIVCLK_DIVIDE (DIVCLK_DIVIDE), .SENS_DIVCLK_DIVIDE (SENS_DIVCLK_DIVIDE),
.REF_JITTER1 (REF_JITTER1), .SENS_REF_JITTER1 (SENS_REF_JITTER1),
.REF_JITTER2 (REF_JITTER2), .SENS_REF_JITTER2 (SENS_REF_JITTER2),
.SS_EN (SS_EN), .SENS_SS_EN (SENS_SS_EN),
.SS_MODE (SS_MODE), .SENS_SS_MODE (SENS_SS_MODE),
.SS_MOD_PERIOD (SS_MOD_PERIOD) .SENS_SS_MOD_PERIOD (SENS_SS_MOD_PERIOD)
) sens_parallel12_i ( ) sens_parallel12_i (
.rst (rst), // input .rst (rst), // input
.pclk (pclk), // input .pclk (pclk), // input
......
sensor/sensors393.v
View file @ 6f36f6d1
...@@ -152,12 +152,12 @@ module sensors393 #( ...@@ -152,12 +152,12 @@ module sensors393 #(
parameter PXD_IBUF_LOW_PWR = "TRUE", parameter PXD_IBUF_LOW_PWR = "TRUE",
parameter PXD_IOSTANDARD = "DEFAULT", parameter PXD_IOSTANDARD = "DEFAULT",
parameter PXD_SLEW = "SLOW", parameter PXD_SLEW = "SLOW",
parameter real REFCLK_FREQUENCY = 300.0, parameter real SENS_REFCLK_FREQUENCY = 300.0,
parameter HIGH_PERFORMANCE_MODE = "FALSE", parameter SENS_HIGH_PERFORMANCE_MODE = "FALSE",
parameter PHASE_WIDTH= 8, // number of bits for te phase counter (depends on divisors) parameter SENS_PHASE_WIDTH= 8, // number of bits for te phase counter (depends on divisors)
parameter PCLK_PERIOD = 10.000, // input period in ns, 0..100.000 - MANDATORY, resolution down to 1 ps parameter SENS_PCLK_PERIOD = 10.000, // input period in ns, 0..100.000 - MANDATORY, resolution down to 1 ps
parameter BANDWIDTH = "OPTIMIZED", //"OPTIMIZED", "HIGH","LOW" parameter SENS_BANDWIDTH = "OPTIMIZED", //"OPTIMIZED", "HIGH","LOW"
parameter CLKFBOUT_MULT_SENSOR = 8, // 100 MHz --> 800 MHz parameter CLKFBOUT_MULT_SENSOR = 8, // 100 MHz --> 800 MHz
parameter CLKFBOUT_PHASE_SENSOR = 0.000, // CLOCK FEEDBACK phase in degrees (3 significant digits, -360.000...+360.000) parameter CLKFBOUT_PHASE_SENSOR = 0.000, // CLOCK FEEDBACK phase in degrees (3 significant digits, -360.000...+360.000)
...@@ -165,16 +165,18 @@ module sensors393 #( ...@@ -165,16 +165,18 @@ module sensors393 #(
parameter IPCLK2X_PHASE = 0.000, parameter IPCLK2X_PHASE = 0.000,
parameter DIVCLK_DIVIDE = 1, // Integer 1..106. Divides all outputs with respect to CLKIN parameter SENS_DIVCLK_DIVIDE = 1, // Integer 1..106. Divides all outputs with respect to CLKIN
parameter REF_JITTER1 = 0.010, // Expectet jitter on CLKIN1 (0.000..0.999) parameter SENS_REF_JITTER1 = 0.010, // Expectet jitter on CLKIN1 (0.000..0.999)
parameter REF_JITTER2 = 0.010, parameter SENS_REF_JITTER2 = 0.010,
parameter SS_EN = "FALSE", // Enables Spread Spectrum mode parameter SENS_SS_EN = "FALSE", // Enables Spread Spectrum mode
parameter SS_MODE = "CENTER_HIGH",//"CENTER_HIGH","CENTER_LOW","DOWN_HIGH","DOWN_LOW" parameter SENS_SS_MODE = "CENTER_HIGH",//"CENTER_HIGH","CENTER_LOW","DOWN_HIGH","DOWN_LOW"
parameter SS_MOD_PERIOD = 10000 // integer 4000-40000 - SS modulation period in ns parameter SENS_SS_MOD_PERIOD = 10000 // integer 4000-40000 - SS modulation period in ns
) ( ) (
input rst, input rst,
// will generate it here // will generate it here
input ref_clk, // IODELAY calibration
input dly_rst,
input pclk, // global clock input, pixel rate (96MHz for MT9P006) input pclk, // global clock input, pixel rate (96MHz for MT9P006)
input pclk2x, // global clock input, double pixel rate (192MHz for MT9P006) input pclk2x, // global clock input, double pixel rate (192MHz for MT9P006)
...@@ -404,27 +406,27 @@ module sensors393 #( ...@@ -404,27 +406,27 @@ module sensors393 #(
.SENSOR_DATA_WIDTH (SENSOR_DATA_WIDTH), .SENSOR_DATA_WIDTH (SENSOR_DATA_WIDTH),
.SENSOR_FIFO_2DEPTH (SENSOR_FIFO_2DEPTH), .SENSOR_FIFO_2DEPTH (SENSOR_FIFO_2DEPTH),
.SENSOR_FIFO_DELAY (SENSOR_FIFO_DELAY), .SENSOR_FIFO_DELAY (SENSOR_FIFO_DELAY),
.IODELAY_GRP ("IODELAY_SENSOR_12"), .IODELAY_GRP ((i & 2)?"IODELAY_SENSOR_34":"IODELAY_SENSOR_12"),
.IDELAY_VALUE (IDELAY_VALUE), .IDELAY_VALUE (IDELAY_VALUE),
.PXD_DRIVE (PXD_DRIVE), .PXD_DRIVE (PXD_DRIVE),
.PXD_IBUF_LOW_PWR (PXD_IBUF_LOW_PWR), .PXD_IBUF_LOW_PWR (PXD_IBUF_LOW_PWR),
.PXD_IOSTANDARD (PXD_IOSTANDARD), .PXD_IOSTANDARD (PXD_IOSTANDARD),
.PXD_SLEW (PXD_SLEW), .PXD_SLEW (PXD_SLEW),
.REFCLK_FREQUENCY (REFCLK_FREQUENCY), .SENS_REFCLK_FREQUENCY (SENS_REFCLK_FREQUENCY),
.HIGH_PERFORMANCE_MODE (HIGH_PERFORMANCE_MODE), .SENS_HIGH_PERFORMANCE_MODE (SENS_HIGH_PERFORMANCE_MODE),
.PHASE_WIDTH (PHASE_WIDTH), .SENS_PHASE_WIDTH (SENS_PHASE_WIDTH),
.PCLK_PERIOD (PCLK_PERIOD), .SENS_PCLK_PERIOD (SENS_PCLK_PERIOD),
.BANDWIDTH (BANDWIDTH), .SENS_BANDWIDTH (SENS_BANDWIDTH),
.CLKFBOUT_MULT_SENSOR (CLKFBOUT_MULT_SENSOR), .CLKFBOUT_MULT_SENSOR (CLKFBOUT_MULT_SENSOR),
.CLKFBOUT_PHASE_SENSOR (CLKFBOUT_PHASE_SENSOR), .CLKFBOUT_PHASE_SENSOR (CLKFBOUT_PHASE_SENSOR),
.IPCLK_PHASE (IPCLK_PHASE), .IPCLK_PHASE (IPCLK_PHASE),
.IPCLK2X_PHASE (IPCLK2X_PHASE), .IPCLK2X_PHASE (IPCLK2X_PHASE),
.DIVCLK_DIVIDE (DIVCLK_DIVIDE), .SENS_DIVCLK_DIVIDE (SENS_DIVCLK_DIVIDE),
.REF_JITTER1 (REF_JITTER1), .SENS_REF_JITTER1 (SENS_REF_JITTER1),
.REF_JITTER2 (REF_JITTER2), .SENS_REF_JITTER2 (SENS_REF_JITTER2),
.SS_EN (SS_EN), .SENS_SS_EN (SENS_SS_EN),
.SS_MODE (SS_MODE), .SENS_SS_MODE (SENS_SS_MODE),
.SS_MOD_PERIOD (SS_MOD_PERIOD) .SENS_SS_MOD_PERIOD (SENS_SS_MOD_PERIOD)
) sensor_channel_i ( ) sensor_channel_i (
.rst (rst), // input .rst (rst), // input
.pclk (pclk), // input .pclk (pclk), // input
...@@ -562,11 +564,29 @@ module sensors393 #( ...@@ -562,11 +564,29 @@ module sensors393 #(
.rq_out (status_rq), // output .rq_out (status_rq), // output
.start_out (status_start) // input .start_out (status_start) // input
); );
idelay_ctrl# (
.IODELAY_GRP("IODELAY_SENSOR_12")
) idelay_ctrl_sensor12_i (
.refclk(ref_clk),
.rst(dly_rst), //rst || dly_rst
.rdy()
);
idelay_ctrl# (
.IODELAY_GRP("IODELAY_SENSOR_34")
) idelay_ctrl_sensor34_i (
.refclk(ref_clk),
.rst(dly_rst), //rst || dly_rst
.rdy()
);
endmodule endmodule
// TODO: if that works, move it to util_modules // TODO: if that works, move it to util_modules
/* /*
.IODELAY_GRP ((i & 2)?"IODELAY_SENSOR_34":"IODELAY_SENSOR_12"),
module my_alias #( module my_alias #(
parameter WIDTH=1 parameter WIDTH=1
) (a,a); ) (a,a);
......
x393.v
View file @ 6f36f6d1
This diff is collapsed.
Markdown is supported
0% or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment