CVC defines set, part1

axi/axibram_write.v

@@ -21,7 +21,9 @@
  *******************************************************************************/
 //`define DEBUG_FIFO 1 
 `include "system_defines.vh" 
-`undef DEBUG_FIFO
+`ifdef DEBUG_FIFO
+  `undef DEBUG_FIFO
+`endif
 module  axibram_write #(
     parameter ADDRESS_BITS = 10 // number of memory address bits
 )(

ddr3/ddr3.v

@@ -528,10 +528,22 @@ module ddr3 (
     integer                rdqs_cntr;
     integer                rdqen_cntr;
     integer                rdq_cntr;
-
-    bufif1 buf_dqs    [DQS_BITS-1:0] (dqs,     dqs_out_dly,  dqs_out_en_dly & {DQS_BITS{out_en}});
-    bufif1 buf_dqs_n  [DQS_BITS-1:0] (dqs_n,   ~dqs_out_dly, dqs_out_en_dly & {DQS_BITS{out_en}});
-    bufif1 buf_dq     [DQ_BITS-1:0]  (dq,      dq_out_dly,   dq_out_en_dly  & {DQ_BITS {out_en}});
+    
+`ifdef CVC
+    wire [DQS_BITS-1:0] dqs_in0 = dqs_out_dly;
+    wire [DQS_BITS-1:0] dqs_in1 = ~dqs_out_dly;
+    wire [DQ_BITS-1:0] dq_in2 = dq_out_dly;
+    wire [DQS_BITS-1:0] dqs_en0 = dqs_out_en_dly & {DQS_BITS{out_en}};
+    wire [DQS_BITS-1:0] dqs_en1 = dqs_out_en_dly & {DQS_BITS{out_en}};
+    wire [DQ_BITS-1:0] dq_en2 = dq_out_en_dly & {DQS_BITS{out_en}};
+    bufif1 buf_dqs    [DQS_BITS-1:0] (dqs,   dqs_in0  ,dqs_en0  );
+    bufif1 buf_dqs_n  [DQS_BITS-1:0] (dqs_n, dqs_in1  ,dqs_en1 );
+    bufif1 buf_dq     [DQ_BITS-1:0]  (dq,  dq_in2    , dq_en2 );
+`else
+    bufif1 buf_dqs    [DQS_BITS-1:0] (dqs,     dqs_out_dly,  dqs_out_en_dly & {DQS_BITS{out_en}     }); 
+    bufif1 buf_dqs_n  [DQS_BITS-1:0] (dqs_n,   ~dqs_out_dly, dqs_out_en_dly & {DQS_BITS{out_en}     }); 
+    bufif1 buf_dq     [DQ_BITS-1:0]  (dq,      dq_out_dly,   dq_out_en_dly  & {DQ_BITS {out_en}     });
+`endif
     assign tdqs_n = {DQS_BITS{1'bz}};
 
     initial begin

includes/x393_tasks_status.vh

@@ -19,7 +19,40 @@
  * along with this program.  If not, see <http://www.gnu.org/licenses/> .
  *******************************************************************************/
 
- 
+`ifdef CVC 
+task wait_status_condition;
+    input [STATUS_DEPTH-1:0] status_address;
+    input [29:0] status_control_address;
+    input  [1:0] status_mode;
+    input [25:0] pattern;        // bits as in read registers
+    input [25:0] mask;           // which bits to compare
+    input        invert_match;   // 0 - wait until match to pattern (all bits), 1 - wait until no match (any of bits differ)
+    input        wait_seq;
+    reg          match;
+    reg    [5:0] seq_num;
+    reg [31:0] pattern1;
+    reg [31:0] mask1;
+    begin
+        WAITING_STATUS = 1;
+        pattern1 = {6'h0,pattern};
+        mask1 = {6'h0,mask};
+        for (match=0; !match; match = invert_match ^ (((registered_rdata ^ pattern1) & mask1)==0)) begin
+            read_status(status_address);
+            if (wait_seq) begin 
+                seq_num = (registered_rdata[STATUS_SEQ_SHFT+:6] ^ 6'h20)&'h30;
+                write_contol_register(status_control_address, {24'b0,status_mode,seq_num});
+                read_status(status_address);
+                while (((registered_rdata[STATUS_SEQ_SHFT+:6] ^ seq_num) & 6'h30)!=0) begin // match just 2 MSBs
+                    read_status(status_address);
+                end
+            end
+        pattern1 = {6'h0,pattern};
+        mask1 = {6'h0,mask};
+        end
+        WAITING_STATUS = 0;
+    end
+endtask
+`else
 task wait_status_condition;
     input [STATUS_DEPTH-1:0] status_address;
     input [29:0] status_control_address;
@@ -46,6 +79,7 @@ task wait_status_condition;
         WAITING_STATUS = 0;
     end
 endtask    
+`endif
 /*
 task wait_status_condition_auto; // assumes status is already updating
     input [STATUS_DEPTH-1:0] status_address;

memctrl/mcntrl_ps_pio.v

@@ -21,7 +21,9 @@
  *******************************************************************************/
 `timescale 1ns/1ps
 `include "system_defines.vh" 
-`undef DEBUG_FIFO
+`ifdef DEBUG_FIFO
+  `undef DEBUG_FIFO
+`endif
 module  mcntrl_ps_pio#(
     parameter MCNTRL_PS_ADDR=                    'h100,
     parameter MCNTRL_PS_MASK=                    'h3e0, // both channels 0 and 1

memctrl/phy/dq_single.v

@@ -110,9 +110,15 @@ idelay_fine_pipe # (
     .data_in(dq_di),
     .data_out(dq_dly)
 );
-
+`ifdef CVC
+parameter FALSE_STING = "FALSE";
+`endif
 iserdes_mem #(
+`ifdef CVC
+    .DYN_CLKDIV_INV_EN(FALSE_STING)
+`else
     .DYN_CLKDIV_INV_EN("FALSE")
+`endif
 ) iserdes_mem_i (
     .iclk(iclk),              // source-synchronous clock
     .oclk(clk),               // system clock, phase should allow iclk-to-oclk jitter with setup/hold margin

system_defines.vh

@@ -13,21 +13,21 @@
  `define def_enable_mem_chn0
  `define def_read_mem_chn0
  `define def_write_mem_chn0
- `undef  def_scanline_chn0
- `undef  def_tiled_chn0
+ //`define  def_scanline_chn0
+ //`define  def_tiled_chn0
  
   // chn 1 is scanline r+w
  `define  def_enable_mem_chn1
  `define  def_read_mem_chn1
  `define  def_write_mem_chn1
  `define  def_scanline_chn1
- `undef   def_tiled_chn1
+ //`define   def_tiled_chn1
 
   // chn 2 is tiled r+w
  `define  def_enable_mem_chn2
  `define  def_read_mem_chn2
  `define  def_write_mem_chn2
- `undef   def_scanline_chn2
+ //`define   def_scanline_chn2
  `define  def_tiled_chn2
 
   // chn 3 is scanline r+w (reuse later)
@@ -35,46 +35,46 @@
  `define  def_read_mem_chn3
  `define  def_write_mem_chn3
  `define  def_scanline_chn3
- `undef   def_tiled_chn3
+ //`define   def_tiled_chn3
 
   // chn 4 is tiled r+w (reuse later)
  `define  def_enable_mem_chn4
  `define  def_read_mem_chn4
  `define  def_write_mem_chn4
- `undef   def_scanline_chn4
+ //`define   def_scanline_chn4
  `define  def_tiled_chn4
 
   // chn 5 is disabled
- `undef def_enable_mem_chn5
+ //`define def_enable_mem_chn5
 
   // chn 6 is disabled
- `undef  def_enable_mem_chn6
+ //`define  def_enable_mem_chn6
  
   // chn 7 is disabled
- `undef  def_enable_mem_chn7
+ //`define  def_enable_mem_chn7
  
   // chn 8 is disabled
- `undef  def_enable_mem_chn8
+ //`define  def_enable_mem_chn8
  
   // chn 9 is disabled
- `undef  def_enable_mem_chn9
+ //`define  def_enable_mem_chn9
  
   // chn 10 is disabled
- `undef  def_enable_mem_chn10
+ //`define  def_enable_mem_chn10
  
   // chn 11 is disabled
- `undef  def_enable_mem_chn11
+ //`define  def_enable_mem_chn11
  
   // chn 12 is disabled
- `undef  def_enable_mem_chn12
+ //`define  def_enable_mem_chn12
  
   // chn 13 is disabled
- `undef  def_enable_mem_chn13
+ //`define  def_enable_mem_chn13
  
   // chn 14 is disabled
- `undef  def_enable_mem_chn14
+ //`define  def_enable_mem_chn14
  
   // chn 15 is disabled
- `undef  def_enable_mem_chn15
+ //`define  def_enable_mem_chn15
 `endif
- 
\ No newline at end of file
+ 

x393_testbench01.tf

@@ -23,7 +23,7 @@
 
 //`define use200Mhz 1
 //`define DEBUG_FIFO 1
-`undef WAIT_MRS
+//`undef WAIT_MRS
 `define SET_PER_PIN_DELAYS 1 // set individual (including per-DQ pin delays)
 `define READBACK_DELAYS 1
 `define PS_PIO_WAIT_COMPLETE 0 // wait until PS PIO module finished transaction before starting a new one
@@ -53,10 +53,18 @@ module  x393_testbench01 #(
 );
 `ifdef IVERILOG              
 //    $display("IVERILOG is defined");
+`ifdef NON_VDT_ENVIROMENT
+    parameter lxtname="x393.lxt";
+`else
     `include "IVERILOG_INCLUDE.v"
+`endif // NON_VDT_ENVIROMENT
 `else
 //    $display("IVERILOG is not defined");
+`ifdef CVC
+    parameter lxtname = "x393.fst";
+`else
     parameter lxtname = "x393.lxt";
+`endif // CVC
 `endif
 `define DEBUG_WR_SINGLE 1  
 `define DEBUG_RD_DATA 1