Commit 4f108db9 authored by Andrey Filippov's avatar Andrey Filippov

more pgm_functions

parent bd35d5ce
This diff is collapsed.
......@@ -341,8 +341,8 @@
#define P_FP1000S 51 ///< Frames per 1000 sec (fps * 1000)
#define P_SENSOR_WIDTH 52 ///< Sensor width
#define P_SENSOR_HEIGHT 53 ///< Sensor height
#define P_COLOR_SATURATION_BLUE 54 ///< 100*realtive saturation blue - preserve?
#define P_COLOR_SATURATION_RED 55 ///< 100*realtive saturation red
#define P_COLOR_SATURATION_BLUE 54 ///< 100*relative saturation blue - preserve?
#define P_COLOR_SATURATION_RED 55 ///< 100*relative saturation red
/// Vignetting control, AX*X^2+BX*X+AY*Y^2+BY*Y+C *** 393: These will need to be split for each subchannel
#define VIGNET_SUBCHN_OFFSET 0 ///< for individual per-subchannel vignetting parameters (add num_sub_chn * VIGNET_SUBCHN_OFFSET)
......@@ -393,13 +393,13 @@
// Are these used anywhere now? ...P_AUTOEXP_SKIP_T
#define P_AUTOEXP_EXP_MAX 81 ///< unsigned long exp_max; /* 100 usec == 1 etc... */
#define P_AUTOEXP_OVEREXP_MAX 82 ///< unsigned long overexp_max; /* percentages for overexposured pixels - 1% == 100, 5% == 500, 0.02% == 2 etc... */
#define P_AUTOEXP_S_PERCENT 83 ///< unsigned long s_percent;(controlling that % of pixels that should have value greater than S_INDEX - below)
#define P_AUTOEXP_S_INDEX 84 ///< unsigned long s_index; Specified number of pixels (S_PERCENT) should have value above S_INDEX
#define P_AUTOEXP_EXP 85 ///< unsigned long exp; Current exposure time
#define P_AUTOEXP_SKIP_PMIN 86 ///< unsigned long skip_pmin; /* percent of delta for skip changes: 1% == 100 */ - no exposure corrections if the desired change is less than that
#define P_AUTOEXP_SKIP_PMAX 87 ///< unsigned long skip_pmax; /* percent of changes for wait one frame before apply changes: 1% == 100 */ - do not apply chnanges if they are to big - wait for the next frame
#define P_AUTOEXP_SKIP_T 88 //v unsigned long skip_t; /* time for skip changes: 100 usec == 1 */ Not quite sure what it is
#define P_AUTOEXP_OVEREXP_MAX 82 ///< unsigned long overexp_max; /* percentages for overexposured pixels - 1% == 100, 5% == 500, 0.02% == 2 etc... */
#define P_AUTOEXP_S_PERCENT 83 ///< unsigned long s_percent;(controlling that % of pixels that should have value greater than S_INDEX - below)
#define P_AUTOEXP_S_INDEX 84 ///< unsigned long s_index; Specified number of pixels (S_PERCENT) should have value above S_INDEX
#define P_AUTOEXP_EXP 85 ///< unsigned long exp; Current exposure time
#define P_AUTOEXP_SKIP_PMIN 86 ///< unsigned long skip_pmin; /* percent of delta for skip changes: 1% == 100 */ - no exposure corrections if the desired change is less than that
#define P_AUTOEXP_SKIP_PMAX 87 ///< unsigned long skip_pmax; /* percent of changes for wait one frame before apply changes: 1% == 100 */ - do not apply chnanges if they are to big - wait for the next frame
#define P_AUTOEXP_SKIP_T 88 ///< unsigned long skip_t; /* time for skip changes: 100 usec == 1 */ Not quite sure what it is
// same as written to the FPGA for the histogram window // 393: Need to split to sub-channels (hist and focus parameters)
#define P_HISTWND_WIDTH 89 ///< autoexposure window width (pixels) - same as written to FPGA
......@@ -418,7 +418,9 @@
#define P_FOCUS_TOTWIDTH 100 ///< (readonly) - total width of the image frame in pixels
#define P_FOCUS_FILTER 101 ///< select 8x8 filter used for the focus calculation (same order as quantization coefficients), 0..14
//!timing generator/trigger delay/external trigger control
//timing generator/trigger delay/external trigger control
//In NC393 P_TRIG_DELAY and P_XMIT_TIMESTAMP are per-channel, other parameters are common (Last modified takes control).
// Master channel is set to the current channels when any of the common parameters is set
#define P_TRIG_CONDITION 102 ///< trigger condition, 0 - internal, else dibits ((use<<1) | level) for each GPIO[11:0] pin
#define P_TRIG_DELAY 103 ///< trigger delay, 32 bits in pixel clocks
#define P_TRIG_OUT 104 ///< trigger output to GPIO, dibits ((use << 1) | level_when_active). Bit 24 - test mode, when GPIO[11:10] are controlled by other internal signals
......@@ -445,10 +447,16 @@
#define P_RFOCUS_HEIGHT 118 ///< relative (0x10000 - 1.0)focus WOI height (3 LSB will be zeroed as it should be multiple of 8x8 block height)
// Obsolete in x393, may need something different
#ifdef NC353
#define P_SDRAM_CHN20 125 ///< data to be written to the SDRAM CH2 REG 0 (last moment) TODO: Obsolete in x393, may need something different
#define P_SDRAM_CHN21 126 ///< data to be written to the SDRAM CH2 REG 1 TODO: Obsolete in x393, may need something different
#define P_SDRAM_CHN22 127 ///< data to be written to the SDRAM CH2 REG 2 TODO: Obsolete in x393, may need something different
#else
#define P_SENSOR_IFACE_TIM0 124 ///< Sensor interface timing/configuration word 0 (different meaning for different interfaces)
#define P_SENSOR_IFACE_TIM1 125///< Sensor interface timing/configuration word 1 (different meaning for different interfaces)
#define P_SENSOR_IFACE_TIM2 126 ///< Sensor interface timing/configuration word 2 (different meaning for different interfaces)
#define P_SENSOR_IFACE_TIM3 127 ///< Sensor interface timing/configuration word 3 (different meaning for different interfaces)
#endif
// The following 4 parameters should have consecutive indexes
// see FRAMEPAIR_MASK_BYTES to modify just part of the word (i.e. scale, not hash16
//
......@@ -1164,9 +1172,10 @@ struct p_names_t {
P_NAME_ENTRY(RFOCUS_WIDTH), \
P_NAME_ENTRY(RFOCUS_TOP), \
P_NAME_ENTRY(RFOCUS_HEIGHT), \
P_NAME_ENTRY(SDRAM_CHN20), \
P_NAME_ENTRY(SDRAM_CHN21), \
P_NAME_ENTRY(SDRAM_CHN22), \
P_NAME_ENTRY(SENSOR_IFACE_TIM0), \
P_NAME_ENTRY(SENSOR_IFACE_TIM1), \
P_NAME_ENTRY(SENSOR_IFACE_TIM2), \
P_NAME_ENTRY(SENSOR_IFACE_TIM3), \
P_NAME_ENTRY(COMPRESSOR_RUN), \
P_NAME_ENTRY(COMPRESSOR_SINGLE), \
P_NAME_ENTRY(COMPMOD_BYRSH), \
......
Markdown is supported
0% or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment