Mor DDR registers

ezynq_ddrcfg_defs.py

@@ -59,6 +59,9 @@ DDR_CFG_DEFS=[
                 'DESCRIPTION':'Number of DDR banks'},              
     {'NAME':'BANK_ADDR_MAP',  'CONF_NAME':'CONFIG_EZYNQ_DDR_BANK_ADDR_MAP','TYPE':'I','MANDATORY':True,'DERIVED':False,'DEFAULT':10,
                 'DESCRIPTION':'DRAM address mapping: number of combined column and row addresses lower than BA0'},              
+
+    {'NAME':'ARB_PAGE_BANK',  'CONF_NAME':'CONFIG_EZYNQ_DDR_ARB_PAGE_BANK','TYPE':'B','MANDATORY':False,'DERIVED':False,'DEFAULT':False,
+                'DESCRIPTION':'Enable Arbiter prioritization based on page/bank match'},              
               
     {'NAME':'ECC',             'CONF_NAME':'CONFIG_EZYNQ_DDR_ECC','TYPE':'B','MANDATORY':False,'DERIVED':False,'DEFAULT':False,
                 'DESCRIPTION':'Enable ECC for the DDR memory'},
@@ -160,7 +163,19 @@ DDR_CFG_DEFS=[
     {'NAME':'ZQCL',             'CONF_NAME':'CONFIG_EZYNQ_DDR_ZQCL','TYPE':'I','MANDATORY':False,'DERIVED':False,'DEFAULT':512,
                 'DESCRIPTION':'ZQCL command: long calibration time, including init (in tCK)'},
 
-                            
+    {'NAME':'INIT2',             'CONF_NAME':'CONFIG_EZYNQ_DDR_INIT2','TYPE':'I','MANDATORY':False,'DERIVED':False,'DEFAULT':5,
+                'DESCRIPTION':'LPDDR2 only: tINIT2 (in tCK): clock stable before CKE high'},
+    {'NAME':'T_INIT4_US',        'CONF_NAME':'CONFIG_EZYNQ_DDR_T_INIT4_US','TYPE':'F','MANDATORY':False,'DERIVED':False,'DEFAULT':1.0,
+                'DESCRIPTION':'LPDDR2 only: tINIT4 (in us)- minimal idle time after RESET command.'},   
+    {'NAME':'T_INIT5_US',        'CONF_NAME':'CONFIG_EZYNQ_DDR_T_INIT5_US','TYPE':'F','MANDATORY':False,'DERIVED':False,'DEFAULT':10.0,
+                'DESCRIPTION':'LPDDR2 only: tINIT5 (in us)- maximal duration of device auto initialization.'},   
+    {'NAME':'T_ZQINIT_US',       'CONF_NAME':'CONFIG_EZYNQ_DDR_T_ZQINIT_US','TYPE':'F','MANDATORY':False,'DERIVED':False,'DEFAULT':1.0,
+                'DESCRIPTION':'LPDDR2 only: tZQINIT (in us)- ZQ initial calibration time.'},   
+
+# CONFIG_EZYNQ_DDR_T_INIT4_US =  1.0 #(us) LPDDR2 ONLY
+# CONFIG_EZYNQ_DDR_T_INIT5_US =  10.0 #(us) LPDDR2 ONLY
+# CONFIG_EZYNQ_DDR_T_ZQINIT_US = 1.0 #(us) LPDDR2 ONLY
+
                  
 ]
 # CONFIG_EZYNQ_DDR3_RTT = 60 # DISABLED, 60,120,40 - only used for DDR3              
@@ -193,6 +208,13 @@ DDR_CFG_DEFS=[
 #CONFIG_EZYNQ_DDR_ZQCS = 64
 #CONFIG_EZYNQ_DDR_ZQCL = 512
 
+# CONFIG_EZYNQ_DDR_INIT2 = 5 #LPDDR2 ONLY
+# CONFIG_EZYNQ_DDR_T_INIT4_US =  1.0 #(us) LPDDR2 ONLY
+# CONFIG_EZYNQ_DDR_T_INIT5_US =  10.0 #(us) LPDDR2 ONLY
+# CONFIG_EZYNQ_DDR_T_ZQINIT_US = 1.0 #(us) LPDDR2 ONLY
+
+
+
 
 #TODO make some of (possibly) derived, leave '_T_' for ns only!
 # CONFIG_EZYNQ_DDR_FREQ_MHZ = 533.333333 *
@@ -216,6 +238,7 @@ DDR_CFG_DEFS=[
 # CONFIG_EZYNQ_DDR_ROW_ADDR_COUNT = 15 *
 # CONFIG_EZYNQ_DDR_COL_ADDR_COUNT = 10 *
 # CONFIG_EZYNQ_DDR_BANK_ADDR_MAP  = 10
+# CONFIG_EZYNQ_DDR_ARB_PAGE_BANK  = Y
 
 # CONFIG_EZYNQ_DDR_ENABLE = 1          *
 # CONFIG_EZYNQ_DDR_MEMORY_TYPE = DDR3  *

test.mk

@@ -119,11 +119,15 @@ CONFIG_EZYNQ_DDR_ZQCL = 512
 CONFIG_EZYNQ_DDR_T_MOD = 15.0
 CONFIG_EZYNQ_DDR_MOD =   12
 
+CONFIG_EZYNQ_DDR_INIT2 = 5 #(tCK)LPDDR2 ONLY
+CONFIG_EZYNQ_DDR_T_INIT4_US =  1.0 #(us) LPDDR2 ONLY
+CONFIG_EZYNQ_DDR_T_INIT5_US =  10.0 #(us) LPDDR2 ONLY
+CONFIG_EZYNQ_DDR_T_ZQINIT_US = 1.0 #(us) LPDDR2 ONLY
 
 
 
 
-CONFIG_EZYNQ_DDR_PARTNO = MT41K256M16RE-125
+CONFIG_EZYNQ_DDR_PARTNO = MT41K256M16RE125
 CONFIG_EZYNQ_DDR_DRAM_WIDTH = 16
 #CONFIG_EZYNQ_DDR_DEVICE_CAPACITY_MBITS = 4096 - can be calculated
 CONFIG_EZYNQ_DDR_SPEED_BIN = DDR3_1066F
@@ -148,6 +152,11 @@ CONFIG_EZYNQ_DDR_BANK_ADDR_COUNT = 3
 CONFIG_EZYNQ_DDR_ROW_ADDR_COUNT = 15
 CONFIG_EZYNQ_DDR_COL_ADDR_COUNT = 10
 CONFIG_EZYNQ_DDR_BANK_ADDR_MAP  = 10 # number of combine CA and RA lower than BA0
+
+CONFIG_EZYNQ_DDR_ARB_PAGE_BANK  = N # Y # default N, testing
+
+
+
 CONFIG_EZYNQ_DDR_CL = 7
 CONFIG_EZYNQ_DDR_CWL = 6
 #CONFIG_EZYNQ_DDR_T_RCD = 7
@@ -249,18 +258,3 @@ CONFIG_EZYNQ_DDR_SETREG_ctrl_reg1__reg_ddrc_lpr_num_entries_PRE = 5
 CONFIG_EZYNQ_DDR_SETREG_phy_wr_dqs_cfg0_PRE = 0xAAAAA
 CONFIG_EZYNQ_DDR_SETREG_phy_wr_dqs_cfg0__reg_phy_wr_dqs_slave_delay_PRE = 0x77
 
-
-#                  'reg_ddrc_selfref_en':              {'r':(12,12),'d':0,'c':'Dynamic - 1 - go to Self Refresh when transaction store is empty'},   
-#                  'reserved1':                        {'r':(11,11),'d':0,'m':'R','c':'reserved'},      
-#                  'reg_ddrc_dis_collision_page_opt':  {'r':(10,10),'d':0,'c':'Disable autoprecharge for collisions (write+write or read+write to the same address) when  reg_ddrc_dis_wc==1'},     
-#                  'reg_ddrc_dis_wc':                  {'r':( 9, 9),'d':0,'c':'1 - disable write combine, 0 - enable'},      
-#                  'reg_ddrc_refresh_update_level':    {'r':( 8, 8),'d':0,'c':'Dynamic: toggle to indicate refressh register(s) update'},    
-#                  'reg_ddrc_auto_pre_en':             {'r':( 7, 7),'d':0,'c':'1 - most R/W will be with autoprecharge'},      
-#                  'reg_ddrc_lpr_num_entries':         {'r':( 1, 6),'d':0x1F,'c':'(bit 6 ignored) (Size of low priority transaction store+1). HPR - 32 - this value'},      
-#                  'reg_ddrc_pageclose':               {'r':( 0, 0),'d':0,'c':'1 - close bank if no transactions in the store for it, 0 - keep open until not needed by other'}}}, 
-
-#    'phy_wr_dqs_cfg0':         {'OFFS': 0x154,'DFLT':0x00000000,'RW':'RW','FIELDS':{
-#                  'reg_phy_wr_dqs_slave_delay':       {'r':(11,19),'d':0,'c':'If reg_phy_wr_dqs_slave_force is 1, use this tap/delay value for write DQS slave DLL, data slice 0'},       
-#                  'reg_phy_wr_dqs_slave_force':       {'r':(10,10),'d':0,'c':'0 - use reg_phy_wr_dqs_slave_ratio  for the write DQS slave DLL, 1 - use provided in reg_phy_wr_dqs_slave_delay, data slice 0'},       
-#                  'reg_phy_wr_dqs_slave_ratio':       {'r':( 0, 9),'d':0,'c':'Fraction of the clock cycle (256 = full period) for the write DQS slave DLL, data slice 0. Program manual training ratio'}}},
-