Skip to content

X
x393
Commit 946b2e55 authored by Andrey Filippov's avatar Andrey Filippov
Browse files
Options

testing/updating DDR3 training algorithms

parent 8105543d
Show whitespace changes
Inline Side-by-side
Showing with 358 additions and 123 deletions
py393/hargs-auto
View file @ 946b2e55
...@@ -3,5 +3,5 @@ ...@@ -3,5 +3,5 @@
-f /usr/local/verilog/x393_parameters.vh /usr/local/verilog/x393_cur_params_target.vh /usr/local/verilog/x393_localparams.vh -f /usr/local/verilog/x393_parameters.vh /usr/local/verilog/x393_cur_params_target.vh /usr/local/verilog/x393_localparams.vh
-l /usr/local/verilog/x393_cur_params_target.vh -l /usr/local/verilog/x393_cur_params_target.vh
-p PICKLE="/usr/local/verilog/x393_mcntrl.pickle -p PICKLE="/usr/local/verilog/x393_mcntrl.pickle
-c measure_all "*ICWRPOASZB" 1 2 2 0xaa 1 0 0 3 -c measure_all
-c save -c save
py393/x393_mcntrl_adjust.py
View file @ 946b2e55
...@@ -68,6 +68,7 @@ class X393McntrlAdjust(object): ...@@ -68,6 +68,7 @@ class X393McntrlAdjust(object):
x393_mcntrl_buffers=None x393_mcntrl_buffers=None
x393_utils=None x393_utils=None
verbose=1 verbose=1
wlev_all_bits = False # write leveling reported on allDQ lines
adjustment_state={} adjustment_state={}
def __init__(self, debug_mode=1,dry_mode=True, saveFileName=None): def __init__(self, debug_mode=1,dry_mode=True, saveFileName=None):
self.DEBUG_MODE= debug_mode self.DEBUG_MODE= debug_mode
...@@ -611,6 +612,7 @@ class X393McntrlAdjust(object): ...@@ -611,6 +612,7 @@ class X393McntrlAdjust(object):
filter_dqo= filter_dqo, filter_dqo= filter_dqo,
cost= cost, cost= cost,
forgive_missing= forgive_missing, forgive_missing= forgive_missing,
allow_replace = True,
maxPhaseErrorsPS=maxPhaseErrorsPS, maxPhaseErrorsPS=maxPhaseErrorsPS,
quiet= quiet) quiet= quiet)
if delays is None: #May also be an empty dictionary? if delays is None: #May also be an empty dictionary?
...@@ -654,14 +656,15 @@ class X393McntrlAdjust(object): ...@@ -654,14 +656,15 @@ class X393McntrlAdjust(object):
def get_all_delays(self, def get_all_delays(self,
phase, phase,
filter_cmda=None, # may be special case: 'S<safe_phase_as_float_number> filter_cmda = None, # may be special case: 'S<safe_phase_as_float_number>
filter_dqsi=None, filter_dqsi = None,
filter_dqi= None, filter_dqi = None,
filter_dqso=None, filter_dqso = None,
filter_dqo= None, filter_dqo = None,
forgive_missing=False, forgive_missing = False,
cost=None, allow_replace = True,
maxPhaseErrorsPS=None, cost = None,
maxPhaseErrorsPS = None,
quiet=3): quiet=3):
""" """
Calculate dictionary of delays for specific phase. Only Non-None filters will generate items in the dictionary Calculate dictionary of delays for specific phase. Only Non-None filters will generate items in the dictionary
...@@ -673,6 +676,7 @@ class X393McntrlAdjust(object): ...@@ -673,6 +676,7 @@ class X393McntrlAdjust(object):
@param filter_dqso filter for DQS output delays @param filter_dqso filter for DQS output delays
@param filter_dqo filter for DQS output delays, @param filter_dqo filter for DQS output delays,
@param forgive_missing do not raise exceptions on missing data - just skip that delay group @param forgive_missing do not raise exceptions on missing data - just skip that delay group
@param allow_replace Try to find solutions fro close phases
@param cost - cost of switching to a higher(lower) delay branch as a fraction of a period @param cost - cost of switching to a higher(lower) delay branch as a fraction of a period
@param maxPhaseErrorsPS - if present, specifies maximal phase errors (in ps) for cmda, dqsi and dqso (each can be None) @param maxPhaseErrorsPS - if present, specifies maximal phase errors (in ps) for cmda, dqsi and dqso (each can be None)
...@@ -698,6 +702,7 @@ class X393McntrlAdjust(object): ...@@ -698,6 +702,7 @@ class X393McntrlAdjust(object):
filter_dqso = filter_dqso, filter_dqso = filter_dqso,
filter_dqo = filter_dqo, filter_dqo = filter_dqo,
forgive_missing = forgive_missing, forgive_missing = forgive_missing,
allow_replace = allow_replace,
cost= cost, cost= cost,
maxPhaseErrorsPS=maxPhaseErrorsPS, maxPhaseErrorsPS=maxPhaseErrorsPS,
quiet= quiet)) quiet= quiet))
...@@ -777,7 +782,9 @@ class X393McntrlAdjust(object): ...@@ -777,7 +782,9 @@ class X393McntrlAdjust(object):
return None return None
if not all_good: # try to fix - see if the solutions exist for slightly different phases if not all_good: # try to fix - see if the solutions exist for slightly different phases
if quiet < 3: if quiet < 3:
print ("phase= %d, delays= %s"%(phase,str(delays))) print ("Not all good: allow_replace = %d, phase= %d, delays= %s"%(allow_replace, phase,str(delays)))
if not allow_replace:
raise Exception ("Not all good solutions for this phase")
for pair in ((CMDA_KEY,CMDA_KEY,),(DQSI_KEY,DQI_KEY),(DQSO_KEY,DQO_KEY)): # will do some double work for CMDA_KEY for pair in ((CMDA_KEY,CMDA_KEY,),(DQSI_KEY,DQI_KEY),(DQSO_KEY,DQO_KEY)): # will do some double work for CMDA_KEY
if (pair[0] in phaseTolerances) and phaseTolerances[pair[0]] and (pair[0] in delays) and (pair[1] in delays): # so not to process forgive_missing again if (pair[0] in phaseTolerances) and phaseTolerances[pair[0]] and (pair[0] in delays) and (pair[1] in delays): # so not to process forgive_missing again
...@@ -1119,11 +1126,45 @@ class X393McntrlAdjust(object): ...@@ -1119,11 +1126,45 @@ class X393McntrlAdjust(object):
self.x393_mcntrl_timing.axi_set_cmda_odelay(combine_delay(cmda_odly_lin),quiet=quiet) self.x393_mcntrl_timing.axi_set_cmda_odelay(combine_delay(cmda_odly_lin),quiet=quiet)
self.x393_axi_tasks.enable_refresh(1) self.x393_axi_tasks.enable_refresh(1)
return cmda_odly_lin return cmda_odly_lin
def write_levelling_allbits(self,
wait_complete=1, # Wait for operation to complete
nburst=16,
quiet=1):
"""
Use when result is on all bits. Data may be inconsistent (not 0/ff) if read phase is wrong, so try
step to change it
@param wait_complete wait write levelling operation to complete (0 - may initiate multiple PS PIO operations)
@param nburst number of 8-bursts written (should match sequence!)
@param quiet reduce output
@eturn a pair of ratios for getting "1" for 2 lanes and problem marker (should be 0), added 4-th value for LY
"""
wlev_max_bad=0.01 # <= OK, > bad
if quiet < 1:
print("--- write_levelling_allbits--- ")
delay_dflt=(split_delay(vrlg.get_default_field("DLY_LANE0_IDELAY",8)),
split_delay(vrlg.get_default_field("DLY_LANE1_IDELAY",8)))
delay_up = ((delay_dflt[0]+(NUM_DLY_STEPS/4))%NUM_DLY_STEPS, (delay_dflt[1]+(NUM_DLY_STEPS/4))%NUM_DLY_STEPS)
self.x393_mcntrl_timing.axi_set_dqs_idelay((combine_delay(delay_dflt[0]),combine_delay(delay_dflt[1])),quiet=quiet)
wlev_rslt=self.x393_pio_sequences.write_levelling(wait_complete, nburst, quiet)
if quiet < 1:
print("wlev_rslt=",wlev_rslt)
if wlev_rslt[3] > wlev_max_bad:
if quiet < 1:
print("Default dqs input delay (%d,%d) results in ambiguous wlev results, changing to (%d,%d)"%
(delay_dflt[0],delay_dflt[1],delay_up[0],delay_up[1]))
self.x393_mcntrl_timing.axi_set_dqs_idelay((combine_delay(delay_up[0]),combine_delay(delay_up[1])),quiet=quiet)
wlev_rslt1= self.x393_pio_sequences.write_levelling(wait_complete, nburst, quiet)
#restore default delay
self.x393_mcntrl_timing.axi_set_dqs_idelay((combine_delay(delay_dflt[0]),combine_delay(delay_dflt[1])),quiet=quiet)
if wlev_rslt1[3] < wlev_rslt[3]:
return wlev_rslt1
return wlev_rslt
def adjust_cmda_odelay(self, def adjust_cmda_odelay(self,
start_phase=0, start_phase=0,
reinits=1, #higher the number - more re-inits are used (0 - only where absolutely necessary reinits=1, #higher the number - more re-inits are used (0 - only where absolutely necessary
max_phase_err=0.1, max_phase_err=0.1,
allow_all_bits = True,
quiet=1 quiet=1
): ):
""" """
...@@ -1135,6 +1176,7 @@ class X393McntrlAdjust(object): ...@@ -1135,6 +1176,7 @@ class X393McntrlAdjust(object):
@param start_phase initial phase to start measuremts (non-0 only for debugging dependencies) @param start_phase initial phase to start measuremts (non-0 only for debugging dependencies)
@param reinits higher the number - more re-inits are used (0 - only where absolutely necessary) @param reinits higher the number - more re-inits are used (0 - only where absolutely necessary)
@param max_phase_err maximal phase error for command and address line as a fraction of SDCLK period to consider @param max_phase_err maximal phase error for command and address line as a fraction of SDCLK period to consider
@parame allow_all_bits - allow write leveling to respond on all bits (normally - only on 1)
@param quiet reduce output @param quiet reduce output
""" """
nbursts=16 nbursts=16
...@@ -1145,38 +1187,65 @@ class X393McntrlAdjust(object): ...@@ -1145,38 +1187,65 @@ class X393McntrlAdjust(object):
max_lin_dly=NUM_DLY_STEPS-1 max_lin_dly=NUM_DLY_STEPS-1
wlev_address_bit=7 wlev_address_bit=7
wlev_max_bad=0.01 # <= OK, > bad wlev_max_bad=0.01 # <= OK, > bad
# for MT41K256M16LY-093 (0/ff) need higher threshold
# wlev_max_bad=0.1
#self.wlev_all_bits = False # needed here?
def phase_step(phase,cmda_dly): def phase_step(phase,cmda_dly):
""" """
Find marginal delay for address/comand lines for particular Find marginal delay for address/command lines for particular clock phase
clock pahse Raises exception if failed to get write leveling data even after
Raises exception if failed to get write levelling data even after
changing cmda delay and restarting memory device changing cmda delay and restarting memory device
Returns a tuple of the current cmda_odelay (hardware) and a marginal one for a7 Returns a tuple of the current cmda_odelay (hardware) and a marginal one for a7
""" """
if quiet < 1:
print("==phase_step(%d,%d),self.wlev_all_bits=%d"%(phase,cmda_dly,self.wlev_all_bits))
cmda_dly_lin=split_delay(cmda_dly) cmda_dly_lin=split_delay(cmda_dly)
self.x393_mcntrl_timing.axi_set_phase(phase,quiet=quiet) self.x393_mcntrl_timing.axi_set_phase(phase,quiet=quiet)
self.x393_mcntrl_timing.axi_set_cmda_odelay(cmda_dly,quiet=quiet) self.x393_mcntrl_timing.axi_set_cmda_odelay(cmda_dly,quiet=quiet)
if not self.wlev_all_bits:
wlev_rslt=self.x393_pio_sequences.write_levelling(1, nbursts, quiet+1) wlev_rslt=self.x393_pio_sequences.write_levelling(1, nbursts, quiet+1)
if wlev_rslt[2]>wlev_max_bad: # should be 0, if not - Try to recover if allow_all_bits and (wlev_rslt[3] < wlev_rslt[2]):
self.wlev_all_bits = True
if self.wlev_all_bits: # maybe just set
wlev_rslt=self.write_levelling_allbits(1, nbursts, quiet+1)
bad_wlev = wlev_rslt[2 + (0,1)[self.wlev_all_bits]]
if bad_wlev > wlev_max_bad: # should be 0, if not - Try to recover
if quiet <4: if quiet <4:
print("*** FAILED to read data in write levelling mode, restarting memory device") print("*** FAILED to read data in write leveling mode, restarting memory device")
print(" Retrying with the same cmda_odelay value = 0x%x"%cmda_dly) print(" Retrying with the same cmda_odelay value = 0x%x, wlev_rslt[2] = %f, wlev_rslt[3] = %f"
%(cmda_dly,wlev_rslt[2],wlev_rslt[3]))
self.x393_pio_sequences.restart_ddr3() self.x393_pio_sequences.restart_ddr3()
if self.wlev_all_bits: # try to vary DQS input delay
wlev_rslt=self.write_levelling_allbits(1, nbursts, quiet+1)
else:
# wlev_rslt=self.x393_pio_sequences.write_levelling(1,nbursts, quiet)
wlev_rslt=self.x393_pio_sequences.write_levelling(1,nbursts, quiet) wlev_rslt=self.x393_pio_sequences.write_levelling(1,nbursts, quiet)
if wlev_rslt[2]>wlev_max_bad: # should be 0, if not - change delay and restart memory bad_wlev = wlev_rslt[2 + (0,1)[self.wlev_all_bits]]
if bad_wlev > wlev_max_bad: # should be 0, if not - change delay and restart memory
cmda_dly_old=cmda_dly cmda_dly_old=cmda_dly
if cmda_dly >=recover_cmda_dly_step: if cmda_dly >=recover_cmda_dly_step:
cmda_dly -= recover_cmda_dly_step cmda_dly -= recover_cmda_dly_step
else: else:
cmda_dly += recover_cmda_dly_step cmda_dly += recover_cmda_dly_step
if quiet <4: if quiet <4:
print("*** FAILED to read data in write levelling mode, restarting memory device") print("*** FAILED to read data in write leveling mode, restarting memory device")
print(" old cmda_odelay= 0x%x, new cmda_odelay =0x%x"%(cmda_dly_old,cmda_dly)) print(" old cmda_odelay= 0x%x, new cmda_odelay =0x%x"%(cmda_dly_old,cmda_dly))
self.x393_mcntrl_timing.axi_set_cmda_odelay(cmda_dly,quiet=quiet) self.x393_mcntrl_timing.axi_set_cmda_odelay(cmda_dly,quiet=quiet)
self.x393_pio_sequences.restart_ddr3() self.x393_pio_sequences.restart_ddr3()
wlev_rslt=self.x393_pio_sequences.write_levelling(1, nbursts, quiet)
if wlev_rslt[2]>wlev_max_bad: # should be 0, if not - change delay and restart memory if self.wlev_all_bits: # try to vary DQS input delay
raise Exception("Failed to read in write levelling mode after modifying cmda_odelay, aborting") wlev_rslt=self.write_levelling_allbits(1, nbursts, quiet+1)
else:
# wlev_rslt=self.x393_pio_sequences.write_levelling(1,nbursts, quiet)
wlev_rslt=self.x393_pio_sequences.write_levelling(1,nbursts, -1)
bad_wlev = wlev_rslt[2 + (0,1)[self.wlev_all_bits]]
# wlev_rslt=self.x393_pio_sequences.write_levelling(1, nbursts, quiet)
bad_wlev = wlev_rslt[2 + (0,1)[self.wlev_all_bits]]
if bad_wlev > wlev_max_bad: # should be 0, if not - change delay and restart memory
raise Exception("Failed to read in write leveling mode after modifying cmda_odelay, aborting")
# Try twice step before giving up (was not needed so far) # Try twice step before giving up (was not needed so far)
d_high=max_lin_dly d_high=max_lin_dly
...@@ -1184,8 +1253,13 @@ class X393McntrlAdjust(object): ...@@ -1184,8 +1253,13 @@ class X393McntrlAdjust(object):
combine_delay(d_high), combine_delay(d_high),
wlev_address_bit, wlev_address_bit,
quiet=quiet) quiet=quiet)
if self.wlev_all_bits: # try to vary DQS input delay
wlev_rslt=self.write_levelling_allbits(1, nbursts, quiet+1)
else:
wlev_rslt=self.x393_pio_sequences.write_levelling(1, nbursts, quiet+1) wlev_rslt=self.x393_pio_sequences.write_levelling(1, nbursts, quiet+1)
if not wlev_rslt[2]>wlev_max_bad: bad_wlev = wlev_rslt[2 + (0,1)[self.wlev_all_bits]]
if not bad_wlev > wlev_max_bad:
return (split_delay(cmda_dly),-1) # even maximal delay is not enough to make rising sdclk separate command from A7 return (split_delay(cmda_dly),-1) # even maximal delay is not enough to make rising sdclk separate command from A7
# find marginal value of a7 delay to spoil write levelling mode # find marginal value of a7 delay to spoil write levelling mode
d_high=max_lin_dly d_high=max_lin_dly
...@@ -1193,8 +1267,12 @@ class X393McntrlAdjust(object): ...@@ -1193,8 +1267,12 @@ class X393McntrlAdjust(object):
while d_high > d_low: while d_high > d_low:
dly= (d_high + d_low)//2 dly= (d_high + d_low)//2
self.x393_mcntrl_timing.axi_set_address_odelay(combine_delay(dly),wlev_address_bit,quiet=quiet) self.x393_mcntrl_timing.axi_set_address_odelay(combine_delay(dly),wlev_address_bit,quiet=quiet)
if self.wlev_all_bits: # try to vary DQS input delay
wlev_rslt=self.write_levelling_allbits(1, nbursts, quiet+1)
else:
wlev_rslt=self.x393_pio_sequences.write_levelling(1, nbursts, quiet+1) wlev_rslt=self.x393_pio_sequences.write_levelling(1, nbursts, quiet+1)
if wlev_rslt[2] > wlev_max_bad: bad_wlev = wlev_rslt[2 + (0,1)[self.wlev_all_bits]]
if bad_wlev > wlev_max_bad:
d_high=dly d_high=dly
else: else:
if d_low == dly: if d_low == dly:
...@@ -1479,6 +1557,7 @@ class X393McntrlAdjust(object): ...@@ -1479,6 +1557,7 @@ class X393McntrlAdjust(object):
reinits=1, #higher the number - more re-inits are used (0 - only where absolutely necessary reinits=1, #higher the number - more re-inits are used (0 - only where absolutely necessary
invert=0, # anti-align DQS (should be 180 degrees off from the normal one) invert=0, # anti-align DQS (should be 180 degrees off from the normal one)
dqs_patt=None, dqs_patt=None,
allow_all_bits = True,
quiet=1 quiet=1
): ):
""" """
...@@ -1489,6 +1568,7 @@ class X393McntrlAdjust(object): ...@@ -1489,6 +1568,7 @@ class X393McntrlAdjust(object):
@param reinits=1, #higher the number - more re-inits are used (0 - only where absolutely necessary @param reinits=1, #higher the number - more re-inits are used (0 - only where absolutely necessary
@param invert=0, # anti-align DQS (should be 180 degrees off from the normal one), can be used to find duty cycle of the clock @param invert=0, # anti-align DQS (should be 180 degrees off from the normal one), can be used to find duty cycle of the clock
@param dqs_patt set and store in global data DQS pattern to use during writes @param dqs_patt set and store in global data DQS pattern to use during writes
@parame allow_all_bits - allow write leveling to respond on all bits (normally - only on 1)
@param quiet=1 @param quiet=1
""" """
nbursts=16 nbursts=16
...@@ -1501,7 +1581,10 @@ class X393McntrlAdjust(object): ...@@ -1501,7 +1581,10 @@ class X393McntrlAdjust(object):
if start_phase >=128: if start_phase >=128:
start_phase -= 256 # -128..+127 start_phase -= 256 # -128..+127
max_lin_dly=NUM_DLY_STEPS-1 max_lin_dly=NUM_DLY_STEPS-1
wlev_max_bad=0.01 # <= OK, > bad # wlev_max_bad=0.01 # <= OK, > bad
# for MT41K256M16LY-093 (0/ff) need higher threshold
wlev_max_bad=0.1
numPhaseSteps=len(self.adjustment_state['cmda_bspe']) numPhaseSteps=len(self.adjustment_state['cmda_bspe'])
if quiet < 2: if quiet < 2:
print("cmda_bspe = %s"%str(self.adjustment_state['cmda_bspe'])) print("cmda_bspe = %s"%str(self.adjustment_state['cmda_bspe']))
...@@ -1523,21 +1606,36 @@ class X393McntrlAdjust(object): ...@@ -1523,21 +1606,36 @@ class X393McntrlAdjust(object):
def measure_dqso(dly,force_meas=False): def measure_dqso(dly,force_meas=False):
def norm_wlev(wlev): #change results to invert wlev data def norm_wlev(wlev): #change results to invert wlev data
if invert: if invert:
return [1.0-wlev[0],1.0-wlev[1],wlev[2]] return [1.0-wlev[0],1.0-wlev[1],wlev[2],wlev[3]]
else: else:
return wlev return wlev
if (dqso_cache[dly] is None) or force_meas: if (dqso_cache[dly] is None) or force_meas:
self.x393_mcntrl_timing.axi_set_dqs_odelay(combine_delay(dly),quiet=quiet) self.x393_mcntrl_timing.axi_set_dqs_odelay(combine_delay(dly),quiet=quiet)
wlev_rslt=norm_wlev(self.x393_pio_sequences.write_levelling(1, nbursts, quiet+1)) # wlev_rslt=norm_wlev(self.x393_pio_sequences.write_levelling(1, nbursts, quiet+1))
if wlev_rslt[2]>wlev_max_bad: # should be 0 - otherwise wlev did not work (CMDA?)
# raise Exception("Write levelling gave unexpected data, aborting (may be wrong command/address delay, incorrectly initialized") if not self.wlev_all_bits:
wlev_rslt=self.x393_pio_sequences.write_levelling(1, nbursts, quiet+1)
if allow_all_bits and (wlev_rslt[3] < wlev_rslt[2]):
self.wlev_all_bits = True
if self.wlev_all_bits: # maybe just set
wlev_rslt=self.write_levelling_allbits(1, nbursts, quiet+1)
wlev_rslt=norm_wlev(wlev_rslt)
bad_wlev = wlev_rslt[2 + (0,1)[self.wlev_all_bits]]
if bad_wlev > wlev_max_bad: # should be 0 - otherwise wlev did not work (CMDA?)
# raise Exception("Write leveling gave unexpected data, aborting (may be wrong command/address delay, incorrectly initialized")
#disabling check 04.09.2016 #disabling check 04.09.2016
print ("raise Exception Write levelling gave unexpected data, aborting (may be wrong command/address delay, incorrectly initialized. Phase: %d, cmda_odly_lin=%d"%(phase,cmda_odly_lin)) print ("raise Exception Write leveling gave unexpected data, aborting (may be wrong command/address delay, incorrectly initialized. Phase: %d, cmda_odly_lin=%d"%(phase,cmda_odly_lin))
print ("=== resetting ===") print ("=== resetting ===")
self.x393_pio_sequences.restart_ddr3() self.x393_pio_sequences.restart_ddr3()
wlev_rslt=norm_wlev(self.x393_pio_sequences.write_levelling(1, nbursts, quiet - 1))
if wlev_rslt[2]>wlev_max_bad: # should be 0 - otherwise wlev did not work (CMDA?) # wlev_rslt = norm_wlev(self.x393_pio_sequences.write_levelling(1, nbursts, -1)) # quiet - 1))
print ("Second try: raise Exception Write levelling gave unexpected data, aborting (may be wrong command/address delay, incorrectly initialized. Phase: %d, cmda_odly_lin=%d"%(phase,cmda_odly_lin)) if self.wlev_all_bits: # try to vary DQS input delay
wlev_rslt = norm_wlev(self.write_levelling_allbits(1, nbursts, quiet+1))
else:
wlev_rslt = norm_wlev(self.x393_pio_sequences.write_levelling(1, nbursts, quiet+1))
bad_wlev = wlev_rslt[2 + (0,1)[self.wlev_all_bits]]
if bad_wlev > wlev_max_bad: # should be 0 - otherwise wlev did not work (CMDA?)
print ("Second try: raise Exception Write leveling gave unexpected data, aborting (may be wrong command/address delay, incorrectly initialized. Phase: %d, cmda_odly_lin=%d"%(phase,cmda_odly_lin))
self.x393_pio_sequences.restart_ddr3() self.x393_pio_sequences.restart_ddr3()
dqso_cache[dly] = wlev_rslt dqso_cache[dly] = wlev_rslt
if quiet < 1: if quiet < 1:
...@@ -1962,7 +2060,9 @@ class X393McntrlAdjust(object): ...@@ -1962,7 +2060,9 @@ class X393McntrlAdjust(object):
limit_step=0.125, # initial delay step as a fraction of the period limit_step=0.125, # initial delay step as a fraction of the period
max_phase_err=0.1, max_phase_err=0.1,
quiet=1, quiet=1,
start_dly=0): #just to check dependence start_dly=0,
reinits = True):
""" """
for each DQS input delay find 4 DQ transitions for each DQ bit, for each DQS input delay find 4 DQ transitions for each DQ bit,
then use them to find finedelay for each of the DQS and DQ, then use them to find finedelay for each of the DQS and DQ,
...@@ -1980,6 +2080,8 @@ class X393McntrlAdjust(object): ...@@ -1980,6 +2080,8 @@ class X393McntrlAdjust(object):
if quiet<2: if quiet<2:
print ("timing)=%s, dly_step=%d step180=%d"%(str(timing),dly_step,step180)) print ("timing)=%s, dly_step=%d step180=%d"%(str(timing),dly_step,step180))
self.x393_pio_sequences.set_read_pattern(nrep+3) # set sequence once self.x393_pio_sequences.set_read_pattern(nrep+3) # set sequence once
if reinits:
self.x393_pio_sequences.restart_ddr3()
def patt_dqs_step(dqs_lin): def patt_dqs_step(dqs_lin):
patt_cache=[None]*(max_lin_dly+1) # cache for holding already measured delays patt_cache=[None]*(max_lin_dly+1) # cache for holding already measured delays
...@@ -2332,15 +2434,19 @@ class X393McntrlAdjust(object): ...@@ -2332,15 +2434,19 @@ class X393McntrlAdjust(object):
# save None for fraction in unknown (previous -0.5, next +0.5) # save None for fraction in unknown (previous -0.5, next +0.5)
frac_step=0.125, frac_step=0.125,
sel=1, sel=1,
quiet=1): quiet=1,
reinits = True):
""" """
Scan phase and find DQS input delay value to find when Scan phase and find DQS input delay value to find when
the result changes (it is caused by crossing clock boundarty from extrenal memory device derived the result changes (it is caused by crossing clock boundary from external memory device derived
to system-synchronous one to system-synchronous one
cmda_odelay should be already calibrated, refresh will be turned on. cmda_odelay should be already calibrated, refresh will be turned on.
Uses random/previously written pattern in one memory block (should have some varying data Uses random/previously written pattern in one memory block (should have some varying data
@param quiet reduce output @param quiet reduce output
""" """
if reinits:
self.x393_pio_sequences.restart_ddr3()
try: try:
dqi_dqsi=self.adjustment_state['dqi_dqsi'] dqi_dqsi=self.adjustment_state['dqi_dqsi']
...@@ -2651,17 +2757,21 @@ class X393McntrlAdjust(object): ...@@ -2651,17 +2757,21 @@ class X393McntrlAdjust(object):
frac_step=0.125, frac_step=0.125,
sel=1, sel=1,
quiet=1, quiet=1,
start_dly=0): #just to check dependence start_dly=0,
reinits = True):
""" """
Scan dqs odelay (setting phase appropriately), write Scan dqs odelay (setting phase appropriately), write
0x0000/0xffff/0x0000/0xffff (same as fixed pattern) data and read it with known dqsi/dqi 0x0000/0xffff/0x0000/0xffff (same as fixed pattern) data and read it with known dqsi/dqi
values (maybe even set different phase for read?), discarding first and last 1.5 8-bursts values (maybe even set different phase for read?), discarding first and last 1.5 8-bursts
Measure 4 different transitions for each data bit (rising DQS/rising DQ, falling DQS/falling DQ, Measure 4 different transitions for each data bit (rising DQS/rising DQ, falling DQS/falling DQ,
rising DQS/falling DQ and falling DQS/rising DQ (that allows to measure duty cycles fro both rising DQS/falling DQ and falling DQS/rising DQ (that allows to measure duty cycles for both
DQS and DQ lines DQS and DQ lines
@param quiet reduce output @param quiet reduce output
""" """
if reinits:
self.x393_pio_sequences.restart_ddr3()
# self.load_hardcoded_data() # TODO: REMOVE LATER # self.load_hardcoded_data() # TODO: REMOVE LATER
try: try:
dqi_dqsi=self.adjustment_state['dqi_dqsi'] dqi_dqsi=self.adjustment_state['dqi_dqsi']
...@@ -3223,11 +3333,12 @@ class X393McntrlAdjust(object): ...@@ -3223,11 +3333,12 @@ class X393McntrlAdjust(object):
ra = 0, ra = 0,
ba = 0, ba = 0,
quiet=1, quiet=1,
single=False): single = False,
reinits = True):
# quiet=0): # quiet=0):
""" """
Will raise exception if read non good or bad - that may happen if cmda_odelay is violated too much. Need to re- Will raise exception if read non good or bad - that may happen if cmda_odelay is violated too much. Need to re-
init memory if that happems and possibly re-run with largersafe_phase or safe_phase==0/None to disable this feature init memory if that happens and possibly re-run with larger safe_phase or safe_phase==0/None to disable this feature
Final measurement of output delay on address lines, performed when read/write timing is set Final measurement of output delay on address lines, performed when read/write timing is set
Writes different data in the specified block and then different pattern to all blocks different Writes different data in the specified block and then different pattern to all blocks different
by one row address or bank address bit. by one row address or bank address bit.
...@@ -3242,7 +3353,7 @@ class X393McntrlAdjust(object): ...@@ -3242,7 +3353,7 @@ class X393McntrlAdjust(object):
dqm_patt=None, dqm_patt=None,
quiet=quiet+2) quiet=quiet+2)
except: except:
print("Skipping DQS pattern (0x55/0xaa) control as it is not in gloabal data (dqs_patt=self.adjustment_state['dqs_pattern'])") print("Skipping DQS pattern (0x55/0xaa) control as it is not in global data (dqs_patt=self.adjustment_state['dqs_pattern'])")
num_ba=3 num_ba=3
if not single: if not single:
...@@ -3251,13 +3362,15 @@ class X393McntrlAdjust(object): ...@@ -3251,13 +3362,15 @@ class X393McntrlAdjust(object):
ra = ra, # 0, ra = ra, # 0,
ba = ba, # 0, ba = ba, # 0,
quiet=quiet, #+1, #1, quiet=quiet, #+1, #1,
single=True) # single=False) single=True,# single=False)
reinits = reinits)
pass2=self.measure_addr_odelay(safe_phase=safe_phase, #0.25, # 0 strictly follow cmda_odelay, >0 -program with this fraction of clk period from the margin pass2=self.measure_addr_odelay(safe_phase=safe_phase, #0.25, # 0 strictly follow cmda_odelay, >0 -program with this fraction of clk period from the margin
dqsi_safe_phase=dqsi_safe_phase, dqsi_safe_phase=dqsi_safe_phase,
ra = ra ^ ((1 << vrlg.ADDRESS_NUMBER)-1), # 0, ra = ra ^ ((1 << vrlg.ADDRESS_NUMBER)-1), # 0,
ba = ba ^ ((1 << num_ba)-1), # 0, ba = ba ^ ((1 << num_ba)-1), # 0,
quiet=quiet, #+1, #1, quiet=quiet, #+1, #1,
single=True) # single=False) single=True, # single=False)
reinits = reinits)
self.adjustment_state['addr_meas']=[pass1,pass2] self.adjustment_state['addr_meas']=[pass1,pass2]
if (quiet<4): if (quiet<4):
print ('addr_meas=[') print ('addr_meas=[')
...@@ -3268,7 +3381,7 @@ class X393McntrlAdjust(object): ...@@ -3268,7 +3381,7 @@ class X393McntrlAdjust(object):
if (quiet<4): if (quiet<4):
num_addr=vrlg.ADDRESS_NUMBER num_addr=vrlg.ADDRESS_NUMBER
num_banks=3 num_banks=3
print ("\n measured marginal addresses and bank adresses for each phase") print ("\n measured marginal addresses and bank addresses for each phase")
print ("phase", end=" ") print ("phase", end=" ")
for edge in ("\\_","_/"): for edge in ("\\_","_/"):
for i in range (num_addr): for i in range (num_addr):
...@@ -3308,7 +3421,7 @@ class X393McntrlAdjust(object): ...@@ -3308,7 +3421,7 @@ class X393McntrlAdjust(object):
inv_ra=ra ^ ((1 << vrlg.ADDRESS_NUMBER)-1) inv_ra=ra ^ ((1 << vrlg.ADDRESS_NUMBER)-1)
ca= ra & ((1 << vrlg.COLADDR_NUMBER) -1) ca= ra & ((1 << vrlg.COLADDR_NUMBER) -1)
inv_ba=ba ^ ((1 << num_ba)-1) inv_ba=ba ^ ((1 << num_ba)-1)
print ("quiet=",quiet) #print ("quiet=",quiet)
if quiet<4: if quiet<4:
print("Writing good data to ra=0x%x, ba = 0x%x, ca = 0x%x, refresh will use: inv_ra = 0x%x, inv_ba=0x%x" %(ra,ba,ca,inv_ra,inv_ba)) print("Writing good data to ra=0x%x, ba = 0x%x, ca = 0x%x, refresh will use: inv_ra = 0x%x, inv_ba=0x%x" %(ra,ba,ca,inv_ra,inv_ba))
...@@ -3343,9 +3456,9 @@ class X393McntrlAdjust(object): ...@@ -3343,9 +3456,9 @@ class X393McntrlAdjust(object):
""" """
phase=0 seems to be bad (during wlev), ***temporarily*** just start from 90 degrees shift phase=0 seems to be bad (during wlev), ***temporarily*** just start from 90 degrees shift
""" """
# for phase in range(numPhaseSteps): for phase in range(numPhaseSteps):
for phase_tmp in range(numPhaseSteps): ## for phase_tmp in range(numPhaseSteps):
phase = (phase_tmp + (numPhaseSteps//4)) % numPhaseSteps ## phase = (phase_tmp + (numPhaseSteps//4)) % numPhaseSteps
try: try:
ph_dlys= self.get_all_delays(phase=phase, ph_dlys= self.get_all_delays(phase=phase,
filter_cmda= DFLT_DLY_FILT, # may be special case: 'S<safe_phase_as_float_number> filter_cmda= DFLT_DLY_FILT, # may be special case: 'S<safe_phase_as_float_number>
...@@ -3354,7 +3467,8 @@ class X393McntrlAdjust(object): ...@@ -3354,7 +3467,8 @@ class X393McntrlAdjust(object):
filter_dqso= DFLT_DLY_FILT, #None, # these are not needed here filter_dqso= DFLT_DLY_FILT, #None, # these are not needed here
filter_dqo= DFLT_DLY_FILT, #None, filter_dqo= DFLT_DLY_FILT, #None,
cost= None, cost= None,
forgive_missing=False, forgive_missing = False,
allow_replace = False,
maxPhaseErrorsPS = maxPhaseErrorsPS, #CMDA, DQSI, DQSO maxPhaseErrorsPS = maxPhaseErrorsPS, #CMDA, DQSI, DQSO
quiet= quiet-1) # quiet) quiet= quiet-1) # quiet)
if not ph_dlys is None: if not ph_dlys is None:
...@@ -3362,9 +3476,34 @@ class X393McntrlAdjust(object): ...@@ -3362,9 +3476,34 @@ class X393McntrlAdjust(object):
except: except:
pass pass
else: else:
print ("!!! Could not find a good phase that has valid delays for all signals, relaxing requirements")
for phase in range(numPhaseSteps):
try:
ph_dlys= self.get_all_delays(phase=phase,
filter_cmda= DFLT_DLY_FILT, # may be special case: 'S<safe_phase_as_float_number>
filter_dqsi= DFLT_DLY_FILT,
filter_dqi= DFLT_DLY_FILT,
filter_dqso= DFLT_DLY_FILT, #None, # these are not needed here
filter_dqo= DFLT_DLY_FILT, #None,
cost= None,
forgive_missing = False,
allow_replace = True,
maxPhaseErrorsPS = maxPhaseErrorsPS, #CMDA, DQSI, DQSO
quiet= quiet-1) # quiet)
if not ph_dlys is None:
break
except:
pass
raise Exception("Could not find a valid phase to use") raise Exception("Could not find a valid phase to use")
#phase is usable delay #phase is usable delay
# reprogram refresh # reprogram refresh
if reinits:
self.x393_pio_sequences.restart_ddr3()
self.x393_axi_tasks.enable_refresh(0) # turn off refresh self.x393_axi_tasks.enable_refresh(0) # turn off refresh
self.x393_pio_sequences.set_refresh(vrlg.T_RFC, # input [ 9:0] t_rfc; # =50 for tCK=2.5ns self.x393_pio_sequences.set_refresh(vrlg.T_RFC, # input [ 9:0] t_rfc; # =50 for tCK=2.5ns
vrlg.T_REFI, #input [ 7:0] t_refi; # 48/97 for normal, 16 - for simulation vrlg.T_REFI, #input [ 7:0] t_refi; # 48/97 for normal, 16 - for simulation
...@@ -3388,10 +3527,16 @@ class X393McntrlAdjust(object): ...@@ -3388,10 +3527,16 @@ class X393McntrlAdjust(object):
refresh=True, refresh=True,
forgive_missing=True, forgive_missing=True,
maxPhaseErrorsPS=maxPhaseErrorsPS, maxPhaseErrorsPS=maxPhaseErrorsPS,
quiet=0) # quiet) # To see what delays where used when writing quiet = quiet) # To see what delays where used when writing
if used_delays is None: if used_delays is None:
raise Exception("measure_addr_odelay(): failed to set phase = %d"%(phase)) # raise Exception("measure_addr_odelay(): failed to set phase = %d"%(phase)) #
#Write 0xaaaa pattern to correct block (all used words), address number - to all with a single bit different #Write 0xaaaa pattern to correct block (all used words), address number - to all with a single bit different
"""
TODO: Reset here?
TODO: Read back after writing with nominal delays to make sure it is correct
"""
self.x393_pio_sequences.set_read_block(ba,ra,ca,nbursts+3,sel_wr) self.x393_pio_sequences.set_read_block(ba,ra,ca,nbursts+3,sel_wr)
#prepare and writ 'correct' block: #prepare and writ 'correct' block:
wdata16_good=(good_patt,)*(8*(nbursts+7)) #3)) wdata16_good=(good_patt,)*(8*(nbursts+7)) #3))
...@@ -3403,10 +3548,9 @@ class X393McntrlAdjust(object): ...@@ -3403,10 +3548,9 @@ class X393McntrlAdjust(object):
comp32_good= wdata32_good[4:(nbursts*4)+2] # data to compare with read buffer - discard first 4*32-bit words and the "tail" after nrep*4 words32 comp32_good= wdata32_good[4:(nbursts*4)+2] # data to compare with read buffer - discard first 4*32-bit words and the "tail" after nrep*4 words32
comp32_bad= wdata32_bad[4:(nbursts*4)+2] # data to compare with read buffer - discard first 4*32-bit words and the "tail" after nrep*4 words32 comp32_bad= wdata32_bad[4:(nbursts*4)+2] # data to compare with read buffer - discard first 4*32-bit words and the "tail" after nrep*4 words32
# self.x393_mcntrl_buffers.write_block_buf_chn(0,0,wdata32_good,quiet) # fill block memory (channel, page, number) # self.x393_mcntrl_buffers.write_block_buf_chn(0,0,wdata32_good,quiet) # fill block memory (channel, page, number)
self.x393_mcntrl_buffers.write_block_buf_chn(0,0,wdata32_good,0 ) # fill block memory (channel, page, number) self.x393_mcntrl_buffers.write_block_buf_chn(0,0,wdata32_good,quiet ) # fill block memory (channel, page, number)
self.x393_mcntrl_buffers.write_block_buf_chn(0,0,wdata32_good,0 ) # fill block memory (channel, page, number) self.x393_mcntrl_buffers.write_block_buf_chn(0,0,wdata32_good,quiet ) # fill block memory (channel, page, number)
self.x393_pio_sequences.set_write_block(ba,ra,ca,nbursts+7,extraTgl,sel_wr) # 3,extraTgl,sel_wr) # set sequence to write 'correct' block self.x393_pio_sequences.set_write_block(ba,ra,ca,nbursts+7,extraTgl,sel_wr) # 3,extraTgl,sel_wr) # set sequence to write 'correct' block
self.x393_pio_sequences.set_write_block(ba,ra,ca,nbursts+7,extraTgl,sel_wr) #3,extraTgl,sel_wr)# set sequence to write 'correct' block ###### self.x393_pio_sequences.set_write_block(ba,ra,ca,nbursts+7,extraTgl,sel_wr) #3,extraTgl,sel_wr)# set sequence to write 'correct' block ######
...@@ -3416,7 +3560,7 @@ class X393McntrlAdjust(object): ...@@ -3416,7 +3560,7 @@ class X393McntrlAdjust(object):
self.x393_pio_sequences.write_block() #page= 0, wait_complete=1) # write 'correct' block ################# Repeat self.x393_pio_sequences.write_block() #page= 0, wait_complete=1) # write 'correct' block ################# Repeat
#prepare and write all alternative blocks (different by one address/bank #prepare and write all alternative blocks (different by one address/bank
self.x393_mcntrl_buffers.write_block_buf_chn(0,0,wdata32_bad,quiet) # fill block memory (channel, page, number) self.x393_mcntrl_buffers.write_block_buf_chn(0,0,wdata32_bad, quiet) # fill block memory (channel, page, number)
raba_bits=[] raba_bits=[]
# print('vrlg.ADDRESS_NUMBER=',vrlg.ADDRESS_NUMBER) # print('vrlg.ADDRESS_NUMBER=',vrlg.ADDRESS_NUMBER)
# print('num_ba=',num_ba) # print('num_ba=',num_ba)
...@@ -3443,19 +3587,23 @@ class X393McntrlAdjust(object): ...@@ -3443,19 +3587,23 @@ class X393McntrlAdjust(object):
bank_bit, bank_bit,
force_meas=False): force_meas=False):
if (meas_cache[dly] is None) or force_meas: if (meas_cache[dly] is None) or force_meas:
for _ in range(5): # for _ in range(5):
this_quiet = quiet
for nn in range(15):
if nn > 5:
this_quiet = 0 # to show - what is going on
#set same delays for all cmda bits (should be already done with 'set_phase_with_refresh' #set same delays for all cmda bits (should be already done with 'set_phase_with_refresh'
if not addr_bit is None: if not addr_bit is None:
self.x393_mcntrl_timing.axi_set_address_odelay(combine_delay(dly),addr_bit,quiet=quiet) self.x393_mcntrl_timing.axi_set_address_odelay(combine_delay(dly),addr_bit,quiet=this_quiet)
elif not bank_bit is None: elif not bank_bit is None:
self.x393_mcntrl_timing.axi_set_address_odelay(combine_delay(dly),bank_bit,quiet=quiet) self.x393_mcntrl_timing.axi_set_address_odelay(combine_delay(dly),bank_bit,quiet=this_quiet)
else: else:
raise Exception("BUG: both addr_bit and bank_bit are None") raise Exception("BUG: both addr_bit and bank_bit are None")
if quiet < 1: if this_quiet < 1:
print ('measure_block(%d,%s) - new measurement'%(dly,str(force_meas))) print ('measure_block(%d,%s) - new measurement#%d'%(dly,str(force_meas),nn))
self.x393_pio_sequences.manual_refresh() # run refresh that sets address bit to opposite values to the required row+bank address self.x393_pio_sequences.manual_refresh() # run refresh that sets address bit to opposite values to the required row+bank address
buf=self.x393_pio_sequences.read_block(4 * (nbursts+1) +2, buf=self.x393_pio_sequences.read_block(4 * (nbursts+1) +2,
(0,1)[quiet<1], #show_rslt, (0,1)[this_quiet<1], #show_rslt,
1) # wait_complete=1) 1) # wait_complete=1)
# buf= buf[4:(nbursts*4)+4] # discard first 4*32-bit words and the "tail" after nrep*4 words32 # buf= buf[4:(nbursts*4)+4] # discard first 4*32-bit words and the "tail" after nrep*4 words32
buf= buf[4:(nbursts*4)+2] # discard first 4*32-bit words and the "tail" after nrep*4 words32 buf= buf[4:(nbursts*4)+2] # discard first 4*32-bit words and the "tail" after nrep*4 words32
...@@ -3464,15 +3612,34 @@ class X393McntrlAdjust(object): ...@@ -3464,15 +3612,34 @@ class X393McntrlAdjust(object):
elif buf==comp32_bad: elif buf==comp32_bad:
meas=False meas=False
else: else:
if this_quiet < 4:
print ("Inconclusive result for comparing read data for phase=%d, addr_bit=%s, bank_bit=%s dly=%d"%(phase,str(addr_bit),str(bank_bit),dly), end = " ") print ("Inconclusive result for comparing read data for phase=%d, addr_bit=%s, bank_bit=%s dly=%d"%(phase,str(addr_bit),str(bank_bit),dly), end = " ")
# print ("Data read from memory=",buf, "(",convert_w32_to_mem16(buf),")")
print ("Data read from memory=%s(%s)"%(self.hex_list(buf),self.hex_list(convert_w32_to_mem16(buf)))) print ("Data read from memory=%s(%s)"%(self.hex_list(buf),self.hex_list(convert_w32_to_mem16(buf))))
#hex_list #hex_list
# print ("Expected 'good' data=%s(%s)"%(self.hex_list(comp32_good),self.hex_list(convert_w32_to_mem16(comp32_good)))) # print ("Expected 'good' data=%s(%s)"%(self.hex_list(comp32_good),self.hex_list(convert_w32_to_mem16(comp32_good))))
# print ("Expected 'bad' data=%s(%s)"%(self.hex_list(comp32_bad),self.hex_list(convert_w32_to_mem16(comp32_bad)))) # print ("Expected 'bad' data=%s(%s)"%(self.hex_list(comp32_bad),self.hex_list(convert_w32_to_mem16(comp32_bad))))
meas=None meas=None
if this_quiet < 3 :
print("====DEBUG: re-reading the same buffer")
self.x393_mcntrl_buffers.read_block_buf_chn (chn= 0,
page = 3, # page=3
num_read = 4 * (nbursts+1) +2,
show_rslt = (0,1)[this_quiet<1]) # chn=0, page=3, number of 32-bit words=num, show_rslt
print("====DEBUG: re-reading the same block")
buf=self.x393_pio_sequences.read_block(4 * (nbursts+1) +2,
(0,1)[this_quiet<1], #show_rslt,
1) # wait_complete=1)
print("====DEBUG: re-reading the same block with refresh")
self.x393_pio_sequences.manual_refresh() # run refresh that sets address bit to opposite values to the required row+bank address
buf=self.x393_pio_sequences.read_block(4 * (nbursts+1) +2,
(0,1)[this_quiet<1], #show_rslt,
1) # wait_complete=1)
meas_cache[dly]=meas meas_cache[dly]=meas
if not meas is None: if not meas is None:
if (this_quiet < 4) and (nn>0):
print ("Got right on %d attempt"%(nn))
break break
else: else:
print("***** FAILED to get measurement ******") print("***** FAILED to get measurement ******")
...@@ -3498,7 +3665,8 @@ class X393McntrlAdjust(object): ...@@ -3498,7 +3665,8 @@ class X393McntrlAdjust(object):
filter_dqso= None, # these are not needed here filter_dqso= None, # these are not needed here
filter_dqo= None, filter_dqo= None,
cost= None, cost= None,
forgive_missing=False, forgive_missing= False,
allow_replace = True,
maxPhaseErrorsPS = maxPhaseErrorsPS, maxPhaseErrorsPS = maxPhaseErrorsPS,
quiet= quiet) quiet= quiet)
if ph_dlys is None: if ph_dlys is None:
...@@ -3628,6 +3796,7 @@ class X393McntrlAdjust(object): ...@@ -3628,6 +3796,7 @@ class X393McntrlAdjust(object):
safe_phase=0.25, # 0 strictly follow cmda_odelay, >0 -program with this fraction of clk period from the margin safe_phase=0.25, # 0 strictly follow cmda_odelay, >0 -program with this fraction of clk period from the margin
reinits=1, reinits=1,
tryWrongWlev=1, # try wrong write levelling mode to make sure device is not stuck in write levelling mode tryWrongWlev=1, # try wrong write levelling mode to make sure device is not stuck in write levelling mode
allow_all_bits = True,
quiet=0): quiet=0):
""" """
Measure output delay on 3 command lines - WE, RAS and CAS, only for high-low transitions as controller Measure output delay on 3 command lines - WE, RAS and CAS, only for high-low transitions as controller
...@@ -3637,6 +3806,7 @@ class X393McntrlAdjust(object): ...@@ -3637,6 +3806,7 @@ class X393McntrlAdjust(object):
the command bit is wrong. After each test one read with normal delay is done to make sure the write levelling mode is the command bit is wrong. After each test one read with normal delay is done to make sure the write levelling mode is
turned off - during write levelling mode it is turned on first, then off and marginal command bit delay may cause turned off - during write levelling mode it is turned on first, then off and marginal command bit delay may cause
write levelling to turn on, but not off write levelling to turn on, but not off
@parame allow_all_bits - allow write leveling to respond on all bits (normally - only on 1)
""" """
# self.load_hardcoded_data() # TODO: ******** TEMPORARY - remove later # self.load_hardcoded_data() # TODO: ******** TEMPORARY - remove later
nrep=4 #16 # number of 8-bursts in write levelling mode nrep=4 #16 # number of 8-bursts in write levelling mode
...@@ -3807,12 +3977,24 @@ class X393McntrlAdjust(object): ...@@ -3807,12 +3977,24 @@ class X393McntrlAdjust(object):
# set DQS odelays to get write levelling pattern # set DQS odelays to get write levelling pattern
self.x393_mcntrl_timing.axi_set_dqs_odelay(combine_delay(dly_wlev), quiet=quiet) self.x393_mcntrl_timing.axi_set_dqs_odelay(combine_delay(dly_wlev), quiet=quiet)
#Verify wlev is OK #Verify wlev is OK
wl_rslt=self.x393_pio_sequences.write_levelling(1, nrep, quiet) if not self.wlev_all_bits:
if wl_rslt[2] > margin_error: wl_rslt = self.x393_pio_sequences.write_levelling(1, nrep, quiet)
if allow_all_bits and (wl_rslt[3] < wl_rslt[2]):
self.wlev_all_bits = True
if self.wlev_all_bits: # try to vary DQS input delay
wl_rslt = self.write_levelling_allbits(1, nrep, quiet)
bad_wlev = wl_rslt[2 + (0,1)[self.wlev_all_bits]]
# wl_rslt=self.x393_pio_sequences.write_levelling(1, nrep, quiet)
if bad_wlev > margin_error:
self.x393_pio_sequences.set_write_lev(nrep,False) # write leveling - 'good' mode (if it was not set so) self.x393_pio_sequences.set_write_lev(nrep,False) # write leveling - 'good' mode (if it was not set so)
if self.wlev_all_bits: # try to vary DQS input delay
wl_rslt=self.x393_pio_sequences.write_levelling(1, nrep, quiet) wl_rslt = self.write_levelling_allbits(1, nrep, quiet)
if wl_rslt[2] > margin_error: else:
wl_rslt = self.x393_pio_sequences.write_levelling(1, nrep, quiet)
bad_wlev = wl_rslt[2 + (0,1)[self.wlev_all_bits]]
# wl_rslt=self.x393_pio_sequences.write_levelling(1, nrep, quiet)
if bad_wlev > margin_error:
if not restart: if not restart:
set_delays_with_reinit(phase=phase,restart=True) # try with reinitialization set_delays_with_reinit(phase=phase,restart=True) # try with reinitialization
else: else:
...@@ -3832,31 +4014,54 @@ class X393McntrlAdjust(object): ...@@ -3832,31 +4014,54 @@ class X393McntrlAdjust(object):
print ('measure_block(%d,%d,%d,%d,%s) - new measurement'%(dly,cmda_odly_early[phase],cmd_bit,phase,str(force_meas))) print ('measure_block(%d,%d,%d,%d,%s) - new measurement'%(dly,cmda_odly_early[phase],cmd_bit,phase,str(force_meas)))
self.x393_pio_sequences.manual_refresh() # run refresh that sets address bit to opposite values to the required row+bank address self.x393_pio_sequences.manual_refresh() # run refresh that sets address bit to opposite values to the required row+bank address
wl_rslt=self.x393_pio_sequences.write_levelling(1, nrep, quiet) # wl_rslt=self.x393_pio_sequences.write_levelling(1, nrep, quiet)
meas= not (wl_rslt[2] > margin_error) # not so many errors (normally should be just 0 if not self.wlev_all_bits:
wl_rslt = self.x393_pio_sequences.write_levelling(1, nrep, quiet)
if allow_all_bits and (wl_rslt[3] < wl_rslt[2]):
self.wlev_all_bits = True
self.x393_pio_sequences.manual_refresh() # run refresh that sets address bit to opposite values to the required row+bank address
if self.wlev_all_bits: # try to vary DQS input delay
wl_rslt = self.write_levelling_allbits(1, nrep, quiet)
bad_wlev = wl_rslt[2 + (0,1)[self.wlev_all_bits]]
meas= not (bad_wlev > margin_error) # not so many errors (normally should be just 0
meas_cache[dly]=meas meas_cache[dly]=meas
# now reset command bit delay and make sure it worked # now reset command bit delay and make sure it worked
self.x393_mcntrl_timing.axi_set_cmd_odelay(combine_delay(cmda_odly_early[phase]),None, quiet=quiet) self.x393_mcntrl_timing.axi_set_cmd_odelay(combine_delay(cmda_odly_early[phase]),None, quiet=quiet)
if self.wlev_all_bits:
wl_rslt = self.write_levelling_allbits(1, nrep, quiet)
else:
wl_rslt=self.x393_pio_sequences.write_levelling(1, nrep, quiet) wl_rslt=self.x393_pio_sequences.write_levelling(1, nrep, quiet)
bad_wlev = wl_rslt[2 + (0,1)[self.wlev_all_bits]]
if wl_rslt[2] > margin_error: if bad_wlev > margin_error:
if quiet < 2: if quiet < 2:
print ("measure_block failed to re-read with safe delays for phase=%d, cmd_bit=%d. Resetting memory device, wl_rslt=%s"%(phase,cmd_bit,str(wl_rslt))) print ("measure_block failed to re-read with safe delays for phase=%d, cmd_bit=%d. Resetting memory device, wl_rslt=%s"%(phase,cmd_bit,str(wl_rslt)))
set_delays_with_reinit(phase=phase, restart=True) set_delays_with_reinit(phase=phase, restart=True)
#retry after re-initialization #retry after re-initialization
wl_rslt=self.x393_pio_sequences.write_levelling(1,nrep, quiet) # wl_rslt=self.x393_pio_sequences.write_levelling(1,nrep, quiet)
if wl_rslt[2] > margin_error: if self.wlev_all_bits:
wl_rslt = self.write_levelling_allbits(1, nrep, quiet)
else:
wl_rslt=self.x393_pio_sequences.write_levelling(1, nrep, quiet)
bad_wlev = wl_rslt[2 + (0,1)[self.wlev_all_bits]]
if bad_wlev > margin_error:
raise Exception ("measure_block failed to re-read with safe delays for phase=%d even after re-initializing device, wl_rslt=%s"%(phase,str(wl_rslt))) raise Exception ("measure_block failed to re-read with safe delays for phase=%d even after re-initializing device, wl_rslt=%s"%(phase,str(wl_rslt)))
# Now make sure device responds - setup read "wrong" write levelling (no actually turning on wlev mode) # Now make sure device responds - setup read "wrong" write levelling (no actually turning on wlev mode)
if tryWrongWlev: if tryWrongWlev:
self.x393_pio_sequences.set_write_lev(nrep, True) # 'wrong' write leveling - should not work self.x393_pio_sequences.set_write_lev(nrep, True) # 'wrong' write leveling - should not work
# wl_rslt=self.x393_pio_sequences.write_levelling(1, nrep, quiet)
if self.wlev_all_bits:
wl_rslt = self.write_levelling_allbits(1, nrep, quiet)
else:
wl_rslt=self.x393_pio_sequences.write_levelling(1, nrep, quiet) wl_rslt=self.x393_pio_sequences.write_levelling(1, nrep, quiet)
bad_wlev = wl_rslt[2 + (0,1)[self.wlev_all_bits]]
#restore normal write levelling mode: #restore normal write levelling mode:
self.x393_pio_sequences.set_write_lev(nrep, False) # 'wrong' write leveling - should not work self.x393_pio_sequences.set_write_lev(nrep, False) # 'wrong' write leveling - should not work
if not (wl_rslt[2] > margin_error): if not (bad_wlev > margin_error):
if quiet < 2: if quiet < 2:
print ("!!! Write levelling mode is stuck (not turning off) for phase=%d, wl_rslt=%s"%(phase,str(wl_rslt))) print ("!!! Write levelling mode is stuck (not turning off) for phase=%d, wl_rslt=%s"%(phase,str(wl_rslt)))
set_delays_with_reinit(phase=phase, restart=True) # just do it, no testimng here (wlev mode is already restored set_delays_with_reinit(phase=phase, restart=True) # just do it, no testing here (wlev mode is already restored
else: else:
meas=meas_cache[dly] meas=meas_cache[dly]
...@@ -4435,7 +4640,9 @@ class X393McntrlAdjust(object): ...@@ -4435,7 +4640,9 @@ class X393McntrlAdjust(object):
def set_write_branch(self, def set_write_branch(self,
dqs_pattern=None, dqs_pattern=None,
extraTgl=1, # just in case extraTgl=1, # just in case
quiet=1): quiet=1,
reinits = False):
""" """
Try write mode branches and find sel (early/late write command), even if it does not match read settings Try write mode branches and find sel (early/late write command), even if it does not match read settings
Read mode should already be set up Read mode should already be set up
...@@ -4445,12 +4652,18 @@ class X393McntrlAdjust(object): ...@@ -4445,12 +4652,18 @@ class X393McntrlAdjust(object):
delay vs. phase should be already calibrated delay vs. phase should be already calibrated
@param dqs_pattern - 0x55/0xaa - DQS output toggle pattern. When it is 0x55 primary_set_out is reversed ? @param dqs_pattern - 0x55/0xaa - DQS output toggle pattern. When it is 0x55 primary_set_out is reversed ?
@quiet reduce output @quiet reduce output
@param reinits - re-initialize DDR3 before running this procedure
@return dictioray with a key(s) (early,nominal,late) containing dictionary of {'wbuf_dly':xx, 'sel':Y} or value 'ODD' @return dictioray with a key(s) (early,nominal,late) containing dictionary of {'wbuf_dly':xx, 'sel':Y} or value 'ODD'
if the remaining number of errors is odd if the remaining number of errors is odd
""" """
#temporarily: #temporarily:
# self.load_mcntrl('dbg/x393_mcntrl.pickle') # self.load_mcntrl('dbg/x393_mcntrl.pickle')
#write/used block parameters #write/used block parameters
if reinits:
if quiet < 3:
print ("=== Re-initializing DDR3 before adjusting writes ===")
self.x393_pio_sequences.restart_ddr3()
startValue=0 startValue=0
num8=8 # 8 bursts to read/write num8=8 # 8 bursts to read/write
ca=0 ca=0
...@@ -4466,7 +4679,7 @@ class X393McntrlAdjust(object): ...@@ -4466,7 +4679,7 @@ class X393McntrlAdjust(object):
except: except:
dqs_pattern=vrlg.DFLT_DQS_PATTERN dqs_pattern=vrlg.DFLT_DQS_PATTERN
self.adjustment_state["dqs_pattern"] = dqs_pattern self.adjustment_state["dqs_pattern"] = dqs_pattern
print("Setting default DQS wirite pattern to self.adjustment_state['dqs_pattern'] and to hardware. Check that write levelling already ran") print("Setting default DQS write pattern to self.adjustment_state['dqs_pattern'] and to hardware. Check that write levelling already ran")
self.x393_mcntrl_timing.axi_set_dqs_dqm_patterns(dqs_patt=dqs_pattern, self.x393_mcntrl_timing.axi_set_dqs_dqm_patterns(dqs_patt=dqs_pattern,
dqm_patt=None, dqm_patt=None,
quiet=quiet+2) quiet=quiet+2)
...@@ -4603,10 +4816,18 @@ read_variants= {(-1, (0, 0)): {'sel': 1, 'wbuf_dly': 9}, ...@@ -4603,10 +4816,18 @@ read_variants= {(-1, (0, 0)): {'sel': 1, 'wbuf_dly': 9},
# now go through all write only ramnges, try to find included r/w one, if not - use default_read # now go through all write only ramnges, try to find included r/w one, if not - use default_read
write_settings={} write_settings={}
for k_wo in write_only_map.keys(): for k_wo in write_only_map.keys():
if quiet < 3:
print ("k_wo=",k_wo)
try: try:
for k_rw in read_write_map.keys(): for k_rw in read_write_map.keys():
if quiet < 3:
print ("k_rw=",k_rw)
if (k_rw[0],k_rw[1]) == k_wo: if (k_rw[0],k_rw[1]) == k_wo:
if quiet < 3:
print ("k_rw=k_wo")
phase=(read_write_map[k_rw][0]+read_write_map[k_rw][1]//2)% numPhases phase=(read_write_map[k_rw][0]+read_write_map[k_rw][1]//2)% numPhases
if quiet < 3:
print ("phase=",phase)
write_settings[k_wo]={'cmda_read': k_rw[0], write_settings[k_wo]={'cmda_read': k_rw[0],
'cmda_write': k_rw[0], 'cmda_write': k_rw[0],
'dqi': k_rw[2], 'dqi': k_rw[2],
...@@ -4616,11 +4837,16 @@ read_variants= {(-1, (0, 0)): {'sel': 1, 'wbuf_dly': 9}, ...@@ -4616,11 +4837,16 @@ read_variants= {(-1, (0, 0)): {'sel': 1, 'wbuf_dly': 9},
'read_phase': phase, 'read_phase': phase,
'write_phase': phase, 'write_phase': phase,
'rel_sel':k_wo[0]+k_wo[1][1]-k_wo[1][0]} 'rel_sel':k_wo[0]+k_wo[1][1]-k_wo[1][0]}
if quiet < 3:
print ("write_settings[%s]=%s"%(str(k_wo), str(write_settings[k_wo])))
break break
else: else:
if quiet < 3:
print ('raise Exception("failed")')
raise Exception("failed") # just assert raise Exception("failed") # just assert
except: except:
phase=(write_only_map[k_wo][0]+read_write_map[k_wo][1]//2)% numPhases # phase=(write_only_map[k_wo][0]+read_write_map[k_wo][1]//2)% numPhases #error here
phase=(write_only_map[k_wo][0]+write_only_map[k_wo][1]//2)% numPhases #error here
write_settings[k_wo]={'cmda_write': k_wo[0], write_settings[k_wo]={'cmda_write': k_wo[0],
'dqo': k_wo[1], 'dqo': k_wo[1],
'dqso': k_wo[1][0], 'dqso': k_wo[1][0],
...@@ -4694,7 +4920,10 @@ write_settings= { ...@@ -4694,7 +4920,10 @@ write_settings= {
maxPhaseErrorsPS= None, maxPhaseErrorsPS= None,
quiet=quiet+2) quiet=quiet+2)
if used_delays is None: if used_delays is None:
raise Exception("set_write_branch(): failed to set phase = %d"%(phase)) # raise Exception("set_write_branch(): failed to set phase = %d"%(phase))
print("set_write_branch(): failed to set phase = %d, write_variant_key=%s, variant=%s, wsel=%d"%
(phase,str(write_variant_key),str(variant),wsel))
continue
self.x393_pio_sequences.write_block_inc(num8=num8, # max 512 16-bit words self.x393_pio_sequences.write_block_inc(num8=num8, # max 512 16-bit words
...@@ -4733,6 +4962,8 @@ write_settings= { ...@@ -4733,6 +4962,8 @@ write_settings= {
if (problems_min is None) or (sum(problems) < sum(problems_min)): if (problems_min is None) or (sum(problems) < sum(problems_min)):
problems_min=problems problems_min=problems
best_wsel=wsel best_wsel=wsel
if problems_min is None:
continue
if sum(problems_min) == 0: if sum(problems_min) == 0:
rslt[write_variant_key]={'sel':best_wsel} rslt[write_variant_key]={'sel':best_wsel}
elif (problems_min[0]%2) or (problems_min[1]%2): elif (problems_min[0]%2) or (problems_min[1]%2):
...@@ -4800,7 +5031,7 @@ write_settings= { ...@@ -4800,7 +5031,7 @@ write_settings= {
except: except:
dqs_pattern=vrlg.DFLT_DQS_PATTERN dqs_pattern=vrlg.DFLT_DQS_PATTERN
self.adjustment_state["dqs_pattern"] = dqs_pattern self.adjustment_state["dqs_pattern"] = dqs_pattern
print("Setting default DQS wirite pattern to self.adjustment_state['dqs_pattern'] and to hardware. Check that write levelling already ran") print("Setting default DQS write pattern to self.adjustment_state['dqs_pattern'] and to hardware. Check that write levelling already ran")
self.x393_mcntrl_timing.axi_set_dqs_dqm_patterns(dqs_patt=dqs_pattern, self.x393_mcntrl_timing.axi_set_dqs_dqm_patterns(dqs_patt=dqs_pattern,
dqm_patt=None, dqm_patt=None,
quiet=quiet+2) quiet=quiet+2)
...@@ -5062,15 +5293,15 @@ write_settings= { ...@@ -5062,15 +5293,15 @@ write_settings= {
def measure_all(self, def measure_all(self,
tasks="*DCWRPOASZB", # "ICWRPOA", #"ICWRPOASZB", tasks="*DCWRPOASZB", # "ICWRPOA", #"ICWRPOASZB",
prim_steps=1, prim_steps = 1,
primary_set_in=2, primary_set_in = 2,
primary_set_out=2, primary_set_out = 2,
dqs_pattern=0xaa, dqs_pattern = 0xaa,
rsel=None, # None (any) or 0/1 rsel= 1, #None, # None (any) or 0/1
wsel=None, # None (any) or 0/1 # Seems wsel=0 has a better fit - consider changing wsel= 0, #None, # None (any) or 0/1 # Seems wsel=0 has a better fit - consider changing
extraTgl=0, extraTgl= 0,
quiet=3, quiet= 3,
wbuf_dly=9): # just a hint, start value can be different wbuf_dly = 9): # just a hint, start value can be different
""" """
@param tasks - "*" - load bitfile @param tasks - "*" - load bitfile
...@@ -5078,7 +5309,7 @@ write_settings= { ...@@ -5078,7 +5309,7 @@ write_settings= {
"I" - initialize memory, set refresh "I" - initialize memory, set refresh
"C" cmda, "W' - write levelling, "R" - read levelling (DQI-DQSI), "P" - dqs input phase (DQSI-PHASE), "C" cmda, "W' - write levelling, "R" - read levelling (DQI-DQSI), "P" - dqs input phase (DQSI-PHASE),
"O" - output timing (DQ odelay vs DQS odelay), "A" - address/bank lines output delays, "Z" - print results, "O" - output timing (DQ odelay vs DQS odelay), "A" - address/bank lines output delays, "Z" - print results,
"B" - select R/W brances and get the optimal phase "B" - select R/W branches and get the optimal phase
@param prim_steps - compare measurement with current delay with one lower by 1 primary step (5 fine delay steps), 0 - @param prim_steps - compare measurement with current delay with one lower by 1 primary step (5 fine delay steps), 0 -
compare with one fine step lower compare with one fine step lower
@param primary_set_in - which of the primary sets to use when processing DQi/DQSi results (2 - normal, 0 - other DQS phase) @param primary_set_in - which of the primary sets to use when processing DQi/DQSi results (2 - normal, 0 - other DQS phase)
...@@ -5118,7 +5349,7 @@ write_settings= { ...@@ -5118,7 +5349,7 @@ write_settings= {
measure_addr_odelay_dqsi_safe_phase=0.125 # > 0 - allow DQSI with DQI simultaneously deviate +/- this fraction of a period measure_addr_odelay_dqsi_safe_phase=0.125 # > 0 - allow DQSI with DQI simultaneously deviate +/- this fraction of a period
commonFine=True, # use same values for fine delay for address/bank lines commonFine=True, # use same values for fine delay for address/bank lines
DqsiMaxDlyErr=200.0 # currently just to check multiple overlapping DQSI branches DqsiMaxDlyErr=200.0 # currently just to check multiple overlapping DQSI branches
DqsoMaxDlyErr=200.0 # currently just to check multiple overlapping DQSI branches DqsoMaxDlyErr=500.0 # currently just to check multiple overlapping DQSI branches
CMDAMaxDlyErr=200.0 # currently just to check multiple overlapping DQSI branches CMDAMaxDlyErr=200.0 # currently just to check multiple overlapping DQSI branches
task_data=[ task_data=[
{'key':'*', {'key':'*',
...@@ -5143,6 +5374,7 @@ write_settings= { ...@@ -5143,6 +5374,7 @@ write_settings= {
'params':{'start_phase':0, 'params':{'start_phase':0,
'reinits':1, 'reinits':1,
'max_phase_err':max_phase_err, 'max_phase_err':max_phase_err,
'allow_all_bits':True,
'quiet':quiet+1}}, 'quiet':quiet+1}},
{'key':'W', {'key':'W',
...@@ -5153,6 +5385,7 @@ write_settings= { ...@@ -5153,6 +5385,7 @@ write_settings= {
'reinits':1, 'reinits':1,
'invert':0, 'invert':0,
'dqs_patt':dqs_pattern, 'dqs_patt':dqs_pattern,
'allow_all_bits':True,
'quiet':quiet+1}}, 'quiet':quiet+1}},
{'key':'W', {'key':'W',
...@@ -5172,6 +5405,7 @@ write_settings= { ...@@ -5172,6 +5405,7 @@ write_settings= {
'params':{'safe_phase':safe_phase, 'params':{'safe_phase':safe_phase,
'reinits': 1, 'reinits': 1,
'tryWrongWlev': 1, 'tryWrongWlev': 1,
'allow_all_bits':True,
'quiet': quiet+1}}, 'quiet': quiet+1}},
{'key':'R', {'key':'R',
'func':self.measure_pattern, 'func':self.measure_pattern,
...@@ -5247,7 +5481,8 @@ write_settings= { ...@@ -5247,7 +5481,8 @@ write_settings= {
'dqsi_safe_phase':measure_addr_odelay_dqsi_safe_phase, 'dqsi_safe_phase':measure_addr_odelay_dqsi_safe_phase,
'ra': 0, 'ra': 0,
'ba': 0, 'ba': 0,
'quiet':quiet+1}}, 'quiet':quiet+1,
'reinits':True}},
{'key':'A', {'key':'A',
'func':self.proc_addr_odelay, 'func':self.proc_addr_odelay,
...@@ -5302,7 +5537,7 @@ write_settings= { ...@@ -5302,7 +5537,7 @@ write_settings= {
{'key':'Z', {'key':'Z',
'func':self.show_all_delays, 'func':self.show_all_delays,
'comment':'Printing results table (delays and errors vs. phase)- Only phases that nave valid values for all signals', 'comment':'Printing results table (delays and errors vs. phase)- Only phases that have valid values for all signals',
'params':{'filter_variants':'A', # Here any string 'params':{'filter_variants':'A', # Here any string
'filter_cmda': 'A', 'filter_cmda': 'A',
'filter_dqsi': 'A', 'filter_dqsi': 'A',
...@@ -5545,10 +5780,10 @@ write_settings= { ...@@ -5545,10 +5780,10 @@ write_settings= {
self.adjustment_state.update(dqs_phase) self.adjustment_state.update(dqs_phase)
#combine DQSI and DQI data to get DQ vs. phase #combine DQSI and DQI data to get DQ vs. phase
delays, errors= self._combine_dq_dqs(dqs_data=self.adjustment_state['dqsi_phase_multi'], delays, errors= self._combine_dq_dqs(dqs_data = self.adjustment_state['dqsi_phase_multi'],
dq_enl_data=self.adjustment_state["dqi_dqsi"], dq_enl_data = self.adjustment_state["dqi_dqsi"],
dq_enl_err = self.adjustment_state["maxErrDqsi"], dq_enl_err = self.adjustment_state["maxErrDqsi"],
quiet=quiet) quiet = quiet)
self.adjustment_state['dqi_phase_multi'] = delays self.adjustment_state['dqi_phase_multi'] = delays
self.adjustment_state["dqi_phase_err"] = errors self.adjustment_state["dqi_phase_err"] = errors
return dqs_phase return dqs_phase
...@@ -5759,7 +5994,7 @@ write_settings= { ...@@ -5759,7 +5994,7 @@ write_settings= {
""" """
# self.load_hardcoded_data() # TODO: TEMPORARY - remove later # self.load_hardcoded_data() # TODO: TEMPORARY - remove later
quiet = 0 # 04.10.2016 # quiet = 0 # 04.10.2016
try: try:
......
py393/x393_pio_sequences.py
View file @ 946b2e55
...@@ -1138,7 +1138,7 @@ class X393PIOSequences(object): ...@@ -1138,7 +1138,7 @@ class X393PIOSequences(object):
@param wait_complete wait write levelling operation to complete (0 - may initiate multiple PS PIO operations) @param wait_complete wait write levelling operation to complete (0 - may initiate multiple PS PIO operations)
@param nburst number of 8-bursts written (should match sequence!) @param nburst number of 8-bursts written (should match sequence!)
@param quiet reduce output @param quiet reduce output
@eturn a pair of ratios for getting "1" for 2 lanes and problem marker (should be 0) @eturn a pair of ratios for getting "1" for 2 lanes and problem marker (should be 0), added 4-th value for LY
""" """
numBufWords=2*nburst # twice nrep in set_write_lev numBufWords=2*nburst # twice nrep in set_write_lev
self.wait_ps_pio_done(vrlg.DEFAULT_STATUS_MODE,1); # not no interrupt running cycle - delays are changed immediately self.wait_ps_pio_done(vrlg.DEFAULT_STATUS_MODE,1); # not no interrupt running cycle - delays are changed immediately
...@@ -1182,8 +1182,8 @@ class X393PIOSequences(object): ...@@ -1182,8 +1182,8 @@ class X393PIOSequences(object):
if quiet <1: if quiet <1:
print ("WLEV lanes ratios: %f %f, non 0x00/0x01 byte: %f, non 0x00/0xffs: %f"%(rslt[0],rslt[1],rslt[2],rslt[3])) print ("WLEV lanes ratios: %f %f, non 0x00/0x01 byte: %f, non 0x00/0xffs: %f"%(rslt[0],rslt[1],rslt[2],rslt[3]))
if (rslt[3] < rslt[2]): # if (rslt[3] < rslt[2]):
rslt[2] = rslt[3] # rslt[2] = rslt[3]
return rslt return rslt
def read_levelling(self, def read_levelling(self,
......
Markdown is supported
0% or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment