Commit e94696c1 authored by Oleg Dzhimiev's avatar Oleg Dzhimiev
Browse files

NAND OTP support

parent 527402be

src/drivers/mtd/nand/Kconfig

0 → 100644
+554 −0
Original line number Diff line number Diff line 
config MTD_NAND_ECC

	tristate



config MTD_NAND_ECC_SMC

	bool "NAND ECC Smart Media byte order"

	depends on MTD_NAND_ECC

	default n

	help

	  Software ECC according to the Smart Media Specification.

	  The original Linux implementation had byte 0 and 1 swapped.





menuconfig MTD_NAND

	tristate "NAND Device Support"

	depends on MTD

	select MTD_NAND_IDS

	select MTD_NAND_ECC

	help

	  This enables support for accessing all type of NAND flash

	  devices. For further information see

	  <http://www.linux-mtd.infradead.org/doc/nand.html>.



if MTD_NAND



config MTD_NAND_BCH

	tristate

	select BCH

	depends on MTD_NAND_ECC_BCH

	default MTD_NAND



config MTD_NAND_ECC_BCH

	bool "Support software BCH ECC"

	default n

	help

	  This enables support for software BCH error correction. Binary BCH

	  codes are more powerful and cpu intensive than traditional Hamming

	  ECC codes. They are used with NAND devices requiring more than 1 bit

	  of error correction.



config MTD_NAND_OTP

	bool "Support access to one-time programmable area of some Micron chips"

	select HAVE_MTD_OTP

	help

	  This enables support for reading and writing to the OTP area of some

	  Micron chips.



config MTD_SM_COMMON

	tristate

	default n



config MTD_NAND_DENALI

        tristate "Support Denali NAND controller"

        depends on HAS_DMA

        help

	  Enable support for the Denali NAND controller.  This should be

	  combined with either the PCI or platform drivers to provide device

	  registration.



config MTD_NAND_DENALI_PCI

        tristate "Support Denali NAND controller on Intel Moorestown"

	depends on PCI && MTD_NAND_DENALI

        help

          Enable the driver for NAND flash on Intel Moorestown, using the

          Denali NAND controller core.



config MTD_NAND_DENALI_DT

	tristate "Support Denali NAND controller as a DT device"

	depends on HAVE_CLK && MTD_NAND_DENALI

	help

	  Enable the driver for NAND flash on platforms using a Denali NAND

	  controller as a DT device.



config MTD_NAND_DENALI_SCRATCH_REG_ADDR

        hex "Denali NAND size scratch register address"

        default "0xFF108018"

        depends on MTD_NAND_DENALI_PCI

        help

          Some platforms place the NAND chip size in a scratch register

          because (some versions of) the driver aren't able to automatically

          determine the size of certain chips. Set the address of the

          scratch register here to enable this feature. On Intel Moorestown

          boards, the scratch register is at 0xFF108018.



config MTD_NAND_GPIO

	tristate "GPIO assisted NAND Flash driver"

	depends on GPIOLIB

	help

	  This enables a NAND flash driver where control signals are

	  connected to GPIO pins, and commands and data are communicated

	  via a memory mapped interface.



config MTD_NAND_AMS_DELTA

	tristate "NAND Flash device on Amstrad E3"

	depends on MACH_AMS_DELTA

	default y

	help

	  Support for NAND flash on Amstrad E3 (Delta).



config MTD_NAND_OMAP2

	tristate "NAND Flash device on OMAP2, OMAP3 and OMAP4"

	depends on ARCH_OMAP2PLUS

	help

          Support for NAND flash on Texas Instruments OMAP2, OMAP3 and OMAP4

	  platforms.



config MTD_NAND_OMAP_BCH

	depends on MTD_NAND_OMAP2

	bool "Support hardware based BCH error correction"

	default n

	select BCH

	help

	  This config enables the ELM hardware engine, which can be used to

	  locate and correct errors when using BCH ECC scheme. This offloads

	  the cpu from doing ECC error searching and correction. However some

	  legacy OMAP families like OMAP2xxx, OMAP3xxx do not have ELM engine

	  so this is optional for them.



config MTD_NAND_OMAP_BCH_BUILD

	def_tristate MTD_NAND_OMAP2 && MTD_NAND_OMAP_BCH



config MTD_NAND_IDS

	tristate



config MTD_NAND_RICOH

	tristate "Ricoh xD card reader"

	default n

	depends on PCI

	select MTD_SM_COMMON

	help

	  Enable support for Ricoh R5C852 xD card reader

	  You also need to enable ether

	  NAND SSFDC (SmartMedia) read only translation layer' or new

	  expermental, readwrite

	  'SmartMedia/xD new translation layer'



config MTD_NAND_AU1550

	tristate "Au1550/1200 NAND support"

	depends on MIPS_ALCHEMY

	help

	  This enables the driver for the NAND flash controller on the

	  AMD/Alchemy 1550 SOC.



config MTD_NAND_BF5XX

	tristate "Blackfin on-chip NAND Flash Controller driver"

	depends on BF54x || BF52x

	help

	  This enables the Blackfin on-chip NAND flash controller



	  No board specific support is done by this driver, each board

	  must advertise a platform_device for the driver to attach.



	  This driver can also be built as a module. If so, the module

	  will be called bf5xx-nand.



config MTD_NAND_BF5XX_HWECC

	bool "BF5XX NAND Hardware ECC"

	default y

	depends on MTD_NAND_BF5XX

	help

	  Enable the use of the BF5XX's internal ECC generator when

	  using NAND.



config MTD_NAND_BF5XX_BOOTROM_ECC

	bool "Use Blackfin BootROM ECC Layout"

	default n

	depends on MTD_NAND_BF5XX_HWECC

	help

	  If you wish to modify NAND pages and allow the Blackfin on-chip

	  BootROM to boot from them, say Y here.  This is only necessary

	  if you are booting U-Boot out of NAND and you wish to update

	  U-Boot from Linux' userspace.  Otherwise, you should say N here.



	  If unsure, say N.



config MTD_NAND_S3C2410

	tristate "NAND Flash support for Samsung S3C SoCs"

	depends on ARCH_S3C24XX || ARCH_S3C64XX

	help

	  This enables the NAND flash controller on the S3C24xx and S3C64xx

	  SoCs



	  No board specific support is done by this driver, each board

	  must advertise a platform_device for the driver to attach.



config MTD_NAND_S3C2410_DEBUG

	bool "Samsung S3C NAND driver debug"

	depends on MTD_NAND_S3C2410

	help

	  Enable debugging of the S3C NAND driver



config MTD_NAND_S3C2410_HWECC

	bool "Samsung S3C NAND Hardware ECC"

	depends on MTD_NAND_S3C2410

	help

	  Enable the use of the controller's internal ECC generator when

	  using NAND. Early versions of the chips have had problems with

	  incorrect ECC generation, and if using these, the default of

	  software ECC is preferable.



config MTD_NAND_NDFC

	tristate "NDFC NanD Flash Controller"

	depends on 4xx

	select MTD_NAND_ECC_SMC

	help

	 NDFC Nand Flash Controllers are integrated in IBM/AMCC's 4xx SoCs



config MTD_NAND_S3C2410_CLKSTOP

	bool "Samsung S3C NAND IDLE clock stop"

	depends on MTD_NAND_S3C2410

	default n

	help

	  Stop the clock to the NAND controller when there is no chip

	  selected to save power. This will mean there is a small delay

	  when the is NAND chip selected or released, but will save

	  approximately 5mA of power when there is nothing happening.



config MTD_NAND_DISKONCHIP

	tristate "DiskOnChip 2000, Millennium and Millennium Plus (NAND reimplementation)"

	depends on HAS_IOMEM

	select REED_SOLOMON

	select REED_SOLOMON_DEC16

	help

	  This is a reimplementation of M-Systems DiskOnChip 2000,

	  Millennium and Millennium Plus as a standard NAND device driver,

	  as opposed to the earlier self-contained MTD device drivers.

	  This should enable, among other things, proper JFFS2 operation on

	  these devices.



config MTD_NAND_DISKONCHIP_PROBE_ADVANCED

        bool "Advanced detection options for DiskOnChip"

        depends on MTD_NAND_DISKONCHIP

        help

          This option allows you to specify nonstandard address at which to

          probe for a DiskOnChip, or to change the detection options.  You

          are unlikely to need any of this unless you are using LinuxBIOS.

          Say 'N'.



config MTD_NAND_DISKONCHIP_PROBE_ADDRESS

        hex "Physical address of DiskOnChip" if MTD_NAND_DISKONCHIP_PROBE_ADVANCED

        depends on MTD_NAND_DISKONCHIP

        default "0"

        ---help---

        By default, the probe for DiskOnChip devices will look for a

        DiskOnChip at every multiple of 0x2000 between 0xC8000 and 0xEE000.

        This option allows you to specify a single address at which to probe

        for the device, which is useful if you have other devices in that

        range which get upset when they are probed.



        (Note that on PowerPC, the normal probe will only check at

        0xE4000000.)



        Normally, you should leave this set to zero, to allow the probe at

        the normal addresses.



config MTD_NAND_DISKONCHIP_PROBE_HIGH

        bool "Probe high addresses"

        depends on MTD_NAND_DISKONCHIP_PROBE_ADVANCED

        help

          By default, the probe for DiskOnChip devices will look for a

          DiskOnChip at every multiple of 0x2000 between 0xC8000 and 0xEE000.

          This option changes to make it probe between 0xFFFC8000 and

          0xFFFEE000.  Unless you are using LinuxBIOS, this is unlikely to be

          useful to you.  Say 'N'.



config MTD_NAND_DISKONCHIP_BBTWRITE

	bool "Allow BBT writes on DiskOnChip Millennium and 2000TSOP"

	depends on MTD_NAND_DISKONCHIP

	help

	  On DiskOnChip devices shipped with the INFTL filesystem (Millennium

	  and 2000 TSOP/Alon), Linux reserves some space at the end of the

	  device for the Bad Block Table (BBT).  If you have existing INFTL

	  data on your device (created by non-Linux tools such as M-Systems'

	  DOS drivers), your data might overlap the area Linux wants to use for

	  the BBT.  If this is a concern for you, leave this option disabled and

	  Linux will not write BBT data into this area.

	  The downside of leaving this option disabled is that if bad blocks

	  are detected by Linux, they will not be recorded in the BBT, which

	  could cause future problems.

	  Once you enable this option, new filesystems (INFTL or others, created

	  in Linux or other operating systems) will not use the reserved area.

	  The only reason not to enable this option is to prevent damage to

	  preexisting filesystems.

	  Even if you leave this disabled, you can enable BBT writes at module

	  load time (assuming you build diskonchip as a module) with the module

	  parameter "inftl_bbt_write=1".



config MTD_NAND_DOCG4

	tristate "Support for DiskOnChip G4"

	depends on HAS_IOMEM

	select BCH

	select BITREVERSE

	help

	  Support for diskonchip G4 nand flash, found in various smartphones and

	  PDAs, among them the Palm Treo680, HTC Prophet and Wizard, Toshiba

	  Portege G900, Asus P526, and O2 XDA Zinc.



	  With this driver you will be able to use UBI and create a ubifs on the

	  device, so you may wish to consider enabling UBI and UBIFS as well.



	  These devices ship with the Mys/Sandisk SAFTL formatting, for which

	  there is currently no mtd parser, so you may want to use command line

	  partitioning to segregate write-protected blocks. On the Treo680, the

	  first five erase blocks (256KiB each) are write-protected, followed

	  by the block containing the saftl partition table.  This is probably

	  typical.



config MTD_NAND_SHARPSL

	tristate "Support for NAND Flash on Sharp SL Series (C7xx + others)"

	depends on ARCH_PXA



config MTD_NAND_CAFE

	tristate "NAND support for OLPC CAFÉ chip"

	depends on PCI

	select REED_SOLOMON

	select REED_SOLOMON_DEC16

	help

	  Use NAND flash attached to the CAFÉ chip designed for the OLPC

	  laptop.



config MTD_NAND_CS553X

	tristate "NAND support for CS5535/CS5536 (AMD Geode companion chip)"

	depends on X86_32

	help

	  The CS553x companion chips for the AMD Geode processor

	  include NAND flash controllers with built-in hardware ECC

	  capabilities; enabling this option will allow you to use

	  these. The driver will check the MSRs to verify that the

	  controller is enabled for NAND, and currently requires that

	  the controller be in MMIO mode.



	  If you say "m", the module will be called cs553x_nand.



config MTD_NAND_ATMEL

	tristate "Support for NAND Flash / SmartMedia on AT91 and AVR32"

	depends on ARCH_AT91 || AVR32

	help

	  Enables support for NAND Flash / Smart Media Card interface

	  on Atmel AT91 and AVR32 processors.



config MTD_NAND_PXA3xx

	tristate "NAND support on PXA3xx and Armada 370/XP"

	depends on PXA3xx || ARCH_MMP || PLAT_ORION

	help

	  This enables the driver for the NAND flash device found on

	  PXA3xx processors (NFCv1) and also on Armada 370/XP (NFCv2).



config MTD_NAND_SLC_LPC32XX

	tristate "NXP LPC32xx SLC Controller"

	depends on ARCH_LPC32XX

	help

	  Enables support for NXP's LPC32XX SLC (i.e. for Single Level Cell

	  chips) NAND controller. This is the default for the PHYTEC 3250

	  reference board which contains a NAND256R3A2CZA6 chip.



	  Please check the actual NAND chip connected and its support

	  by the SLC NAND controller.



config MTD_NAND_MLC_LPC32XX

	tristate "NXP LPC32xx MLC Controller"

	depends on ARCH_LPC32XX

	help

	  Uses the LPC32XX MLC (i.e. for Multi Level Cell chips) NAND

	  controller. This is the default for the WORK92105 controller

	  board.



	  Please check the actual NAND chip connected and its support

	  by the MLC NAND controller.



config MTD_NAND_CM_X270

	tristate "Support for NAND Flash on CM-X270 modules"

	depends on MACH_ARMCORE



config MTD_NAND_PASEMI

	tristate "NAND support for PA Semi PWRficient"

	depends on PPC_PASEMI

	help

	  Enables support for NAND Flash interface on PA Semi PWRficient

	  based boards



config MTD_NAND_TMIO

	tristate "NAND Flash device on Toshiba Mobile IO Controller"

	depends on MFD_TMIO

	help

	  Support for NAND flash connected to a Toshiba Mobile IO

	  Controller in some PDAs, including the Sharp SL6000x.



config MTD_NAND_NANDSIM

	tristate "Support for NAND Flash Simulator"

	help

	  The simulator may simulate various NAND flash chips for the

	  MTD nand layer.



config MTD_NAND_GPMI_NAND

        tristate "GPMI NAND Flash Controller driver"

        depends on MTD_NAND && MXS_DMA

        help

	 Enables NAND Flash support for IMX23, IMX28 or IMX6.

	 The GPMI controller is very powerful, with the help of BCH

	 module, it can do the hardware ECC. The GPMI supports several

	 NAND flashs at the same time. The GPMI may conflicts with other

	 block, such as SD card. So pay attention to it when you enable

	 the GPMI.



config MTD_NAND_BCM47XXNFLASH

	tristate "Support for NAND flash on BCM4706 BCMA bus"

	depends on BCMA_NFLASH

	help

	  BCMA bus can have various flash memories attached, they are

	  registered by bcma as platform devices. This enables driver for

	  NAND flash memories. For now only BCM4706 is supported.



config MTD_NAND_PLATFORM

	tristate "Support for generic platform NAND driver"

	depends on HAS_IOMEM

	help

	  This implements a generic NAND driver for on-SOC platform

	  devices. You will need to provide platform-specific functions

	  via platform_data.



config MTD_NAND_ORION

	tristate "NAND Flash support for Marvell Orion SoC"

	depends on PLAT_ORION

	help

	  This enables the NAND flash controller on Orion machines.



	  No board specific support is done by this driver, each board

	  must advertise a platform_device for the driver to attach.



config MTD_NAND_FSL_ELBC

	tristate "NAND support for Freescale eLBC controllers"

	depends on PPC

	select FSL_LBC

	help

	  Various Freescale chips, including the 8313, include a NAND Flash

	  Controller Module with built-in hardware ECC capabilities.

	  Enabling this option will enable you to use this to control

	  external NAND devices.



config MTD_NAND_FSL_IFC

	tristate "NAND support for Freescale IFC controller"

	depends on MTD_NAND && FSL_SOC

	select FSL_IFC

	select MEMORY

	help

	  Various Freescale chips e.g P1010, include a NAND Flash machine

	  with built-in hardware ECC capabilities.

	  Enabling this option will enable you to use this to control

	  external NAND devices.



config MTD_NAND_FSL_UPM

	tristate "Support for NAND on Freescale UPM"

	depends on PPC_83xx || PPC_85xx

	select FSL_LBC

	help

	  Enables support for NAND Flash chips wired onto Freescale PowerPC

	  processor localbus with User-Programmable Machine support.



config MTD_NAND_MPC5121_NFC

	tristate "MPC5121 built-in NAND Flash Controller support"

	depends on PPC_MPC512x

	help

	  This enables the driver for the NAND flash controller on the

	  MPC5121 SoC.



config MTD_NAND_MXC

	tristate "MXC NAND support"

	depends on ARCH_MXC

	help

	  This enables the driver for the NAND flash controller on the

	  MXC processors.



config MTD_NAND_SH_FLCTL

	tristate "Support for NAND on Renesas SuperH FLCTL"

	depends on SUPERH || ARCH_SHMOBILE || COMPILE_TEST

	depends on HAS_IOMEM

	depends on HAS_DMA

	help

	  Several Renesas SuperH CPU has FLCTL. This option enables support

	  for NAND Flash using FLCTL.



config MTD_NAND_DAVINCI

        tristate "Support NAND on DaVinci/Keystone SoC"

        depends on ARCH_DAVINCI || (ARCH_KEYSTONE && TI_AEMIF)

        help

	  Enable the driver for NAND flash chips on Texas Instruments

	  DaVinci/Keystone processors.



config MTD_NAND_TXX9NDFMC

	tristate "NAND Flash support for TXx9 SoC"

	depends on SOC_TX4938 || SOC_TX4939

	help

	  This enables the NAND flash controller on the TXx9 SoCs.



config MTD_NAND_SOCRATES

	tristate "Support for NAND on Socrates board"

	depends on SOCRATES

	help

	  Enables support for NAND Flash chips wired onto Socrates board.



config MTD_NAND_NUC900

	tristate "Support for NAND on Nuvoton NUC9xx/w90p910 evaluation boards."

	depends on ARCH_W90X900

	help

	  This enables the driver for the NAND Flash on evaluation board based

	  on w90p910 / NUC9xx.



config MTD_NAND_PL35X

	tristate "ARM Pl35X NAND flash driver"

	depends on MTD_NAND && ARM

	depends on PL35X_SMC

	help

	  This enables access to the NAND flash device on PL351/PL353

	  SMC controller.



config MTD_NAND_JZ4740

	tristate "Support for JZ4740 SoC NAND controller"

	depends on MACH_JZ4740

	help

		Enables support for NAND Flash on JZ4740 SoC based boards.



config MTD_NAND_FSMC

	tristate "Support for NAND on ST Micros FSMC"

	depends on PLAT_SPEAR || ARCH_NOMADIK || ARCH_U8500 || MACH_U300

	help

	  Enables support for NAND Flash chips on the ST Microelectronics

	  Flexible Static Memory Controller (FSMC)



config MTD_NAND_XWAY

	tristate "Support for NAND on Lantiq XWAY SoC"

	depends on LANTIQ && SOC_TYPE_XWAY

	select MTD_NAND_PLATFORM

	help

	  Enables support for NAND Flash chips on Lantiq XWAY SoCs. NAND is attached

	  to the External Bus Unit (EBU).



config MTD_NAND_SUNXI

	tristate "Support for NAND on Allwinner SoCs"

	depends on ARCH_SUNXI

	help

	  Enables support for NAND Flash chips on Allwinner SoCs.



config MTD_NAND_ARASAN

	tristate "Support for Arasan Nand Flash controller"

	depends on MTD_NAND

	help

	  Enables the driver for the Arasan Nand Flash controller in ZynqMP SoC.



config MTD_NAND_HISI504

	tristate "Support for NAND controller on Hisilicon SoC Hip04"

	depends on HAS_DMA

	help

	  Enables support for NAND controller on Hisilicon SoC Hip04.



endif # MTD_NAND

src/drivers/mtd/nand/Makefile

0 → 100644
+58 −0
Original line number Diff line number Diff line 
#

# linux/drivers/nand/Makefile

#



obj-$(CONFIG_MTD_NAND)			+= nand.o

obj-$(CONFIG_MTD_NAND_ECC)		+= nand_ecc.o

obj-$(CONFIG_MTD_NAND_BCH)		+= nand_bch.o

obj-$(CONFIG_MTD_NAND_IDS)		+= nand_ids.o

obj-$(CONFIG_MTD_SM_COMMON) 		+= sm_common.o



obj-$(CONFIG_MTD_NAND_CAFE)		+= cafe_nand.o

obj-$(CONFIG_MTD_NAND_AMS_DELTA)	+= ams-delta.o

obj-$(CONFIG_MTD_NAND_DENALI)		+= denali.o

obj-$(CONFIG_MTD_NAND_DENALI_PCI)	+= denali_pci.o

obj-$(CONFIG_MTD_NAND_DENALI_DT)	+= denali_dt.o

obj-$(CONFIG_MTD_NAND_AU1550)		+= au1550nd.o

obj-$(CONFIG_MTD_NAND_BF5XX)		+= bf5xx_nand.o

obj-$(CONFIG_MTD_NAND_S3C2410)		+= s3c2410.o

obj-$(CONFIG_MTD_NAND_DAVINCI)		+= davinci_nand.o

obj-$(CONFIG_MTD_NAND_DISKONCHIP)	+= diskonchip.o

obj-$(CONFIG_MTD_NAND_DOCG4)		+= docg4.o

obj-$(CONFIG_MTD_NAND_FSMC)		+= fsmc_nand.o

obj-$(CONFIG_MTD_NAND_SHARPSL)		+= sharpsl.o

obj-$(CONFIG_MTD_NAND_NANDSIM)		+= nandsim.o

obj-$(CONFIG_MTD_NAND_CS553X)		+= cs553x_nand.o

obj-$(CONFIG_MTD_NAND_NDFC)		+= ndfc.o

obj-$(CONFIG_MTD_NAND_ATMEL)		+= atmel_nand.o

obj-$(CONFIG_MTD_NAND_GPIO)		+= gpio.o

obj-$(CONFIG_MTD_NAND_OMAP2) 		+= omap2.o

obj-$(CONFIG_MTD_NAND_OMAP_BCH_BUILD)	+= omap_elm.o

obj-$(CONFIG_MTD_NAND_CM_X270)		+= cmx270_nand.o

obj-$(CONFIG_MTD_NAND_PXA3xx)		+= pxa3xx_nand.o

obj-$(CONFIG_MTD_NAND_TMIO)		+= tmio_nand.o

obj-$(CONFIG_MTD_NAND_PLATFORM)		+= plat_nand.o

obj-$(CONFIG_MTD_NAND_PASEMI)		+= pasemi_nand.o

obj-$(CONFIG_MTD_NAND_ORION)		+= orion_nand.o

obj-$(CONFIG_MTD_NAND_FSL_ELBC)		+= fsl_elbc_nand.o

obj-$(CONFIG_MTD_NAND_FSL_IFC)		+= fsl_ifc_nand.o

obj-$(CONFIG_MTD_NAND_FSL_UPM)		+= fsl_upm.o

obj-$(CONFIG_MTD_NAND_SLC_LPC32XX)      += lpc32xx_slc.o

obj-$(CONFIG_MTD_NAND_MLC_LPC32XX)      += lpc32xx_mlc.o

obj-$(CONFIG_MTD_NAND_SH_FLCTL)		+= sh_flctl.o

obj-$(CONFIG_MTD_NAND_MXC)		+= mxc_nand.o

obj-$(CONFIG_MTD_NAND_SOCRATES)		+= socrates_nand.o

obj-$(CONFIG_MTD_NAND_TXX9NDFMC)	+= txx9ndfmc.o

obj-$(CONFIG_MTD_NAND_NUC900)		+= nuc900_nand.o

obj-$(CONFIG_MTD_NAND_MPC5121_NFC)	+= mpc5121_nfc.o

obj-$(CONFIG_MTD_NAND_RICOH)		+= r852.o

obj-$(CONFIG_MTD_NAND_JZ4740)		+= jz4740_nand.o

obj-$(CONFIG_MTD_NAND_GPMI_NAND)	+= gpmi-nand/

obj-$(CONFIG_MTD_NAND_XWAY)		+= xway_nand.o

obj-$(CONFIG_MTD_NAND_BCM47XXNFLASH)	+= bcm47xxnflash/

obj-$(CONFIG_MTD_NAND_SUNXI)		+= sunxi_nand.o

obj-$(CONFIG_MTD_NAND_PL35X)		+= pl35x_nand.o

obj-$(CONFIG_MTD_NAND_ARASAN)		+= arasan_nfc.o

obj-$(CONFIG_MTD_NAND_HISI504)	        += hisi504_nand.o



nand-objs := nand_base.o nand_bbt.o nand_timings.o nandchip-micron.o

src/drivers/mtd/nand/nand.h

0 → 100644
+13 −0
Original line number Diff line number Diff line 
#include <linux/mtd/mtd.h>



#define NOTALIGNED(x)	((x & (chip->subpagesize - 1)) != 0)



int nand_get_device(struct mtd_info *mtd, int new_state);

void nand_release_device(struct mtd_info *mtd);



int nand_do_read_ops(struct mtd_info *mtd, loff_t from,

			    struct mtd_oob_ops *ops);

int nand_do_write_ops(struct mtd_info *mtd, loff_t to,

			     struct mtd_oob_ops *ops);



void nandchip_micron_init(struct mtd_info *mtd, int dev_id);

src/drivers/mtd/nand/nandchip-micron.c

0 → 100644
+213 −0

File added.

Preview size limit exceeded, changes collapsed.

src/drivers/mtd/nand/pl35x_nand.c

0 → 100644
+1220 −0

File added.

Preview size limit exceeded, changes collapsed.