updated to current version

src/drivers/mtd/nand/Kconfig

@@ -13,7 +13,6 @@ config MTD_NAND_ECC_SMC
 menuconfig MTD_NAND
 	tristate "NAND Device Support"
 	depends on MTD
-	select MTD_NAND_IDS
 	select MTD_NAND_ECC
 	help
 	  This enables support for accessing all type of NAND flash
@@ -37,13 +36,6 @@ config MTD_NAND_ECC_BCH
 	  ECC codes. They are used with NAND devices requiring more than 1 bit
 	  of error correction.
 
-config MTD_NAND_OTP
-	bool "Support access to one-time programmable area of some Micron chips"
-	select HAVE_MTD_OTP
-	help
-	  This enables support for reading and writing to the OTP area of some
-	  Micron chips.
-
 config MTD_SM_COMMON
 	tristate
 	default n
@@ -67,17 +59,6 @@ config MTD_NAND_DENALI_DT
 	  Enable the driver for NAND flash on platforms using a Denali NAND
 	  controller as a DT device.
 
-config MTD_NAND_DENALI_SCRATCH_REG_ADDR
-        hex "Denali NAND size scratch register address"
-        default "0xFF108018"
-        depends on MTD_NAND_DENALI_PCI
-        help
-          Some platforms place the NAND chip size in a scratch register
-          because (some versions of) the driver aren't able to automatically
-          determine the size of certain chips. Set the address of the
-          scratch register here to enable this feature. On Intel Moorestown
-          boards, the scratch register is at 0xFF108018.
-
 config MTD_NAND_GPIO
 	tristate "GPIO assisted NAND Flash driver"
 	depends on GPIOLIB || COMPILE_TEST
@@ -116,9 +97,6 @@ config MTD_NAND_OMAP_BCH
 config MTD_NAND_OMAP_BCH_BUILD
 	def_tristate MTD_NAND_OMAP2 && MTD_NAND_OMAP_BCH
 
-config MTD_NAND_IDS
-	tristate
-
 config MTD_NAND_RICOH
 	tristate "Ricoh xD card reader"
 	default n
@@ -186,15 +164,6 @@ config MTD_NAND_S3C2410_DEBUG
 	help
 	  Enable debugging of the S3C NAND driver
 
-config MTD_NAND_S3C2410_HWECC
-	bool "Samsung S3C NAND Hardware ECC"
-	depends on MTD_NAND_S3C2410
-	help
-	  Enable the use of the controller's internal ECC generator when
-	  using NAND. Early versions of the chips have had problems with
-	  incorrect ECC generation, and if using these, the default of
-	  software ECC is preferable.
-
 config MTD_NAND_NDFC
 	tristate "NDFC NanD Flash Controller"
 	depends on 4xx
@@ -212,6 +181,13 @@ config MTD_NAND_S3C2410_CLKSTOP
 	  when the is NAND chip selected or released, but will save
 	  approximately 5mA of power when there is nothing happening.
 
+config MTD_NAND_TANGO
+	tristate "NAND Flash support for Tango chips"
+	depends on ARCH_TANGO || COMPILE_TEST
+	depends on HAS_DMA
+	help
+	  Enables the NAND Flash controller on Tango chips.
+
 config MTD_NAND_DISKONCHIP
 	tristate "DiskOnChip 2000, Millennium and Millennium Plus (NAND reimplementation)"
 	depends on HAS_IOMEM
@@ -330,15 +306,16 @@ config MTD_NAND_CS553X
 	  If you say "m", the module will be called cs553x_nand.
 
 config MTD_NAND_ATMEL
-	tristate "Support for NAND Flash / SmartMedia on AT91 and AVR32"
-	depends on ARCH_AT91 || AVR32
+	tristate "Support for NAND Flash / SmartMedia on AT91"
+	depends on ARCH_AT91
+	select MFD_ATMEL_SMC
 	help
 	  Enables support for NAND Flash / Smart Media Card interface
-	  on Atmel AT91 and AVR32 processors.
+	  on Atmel AT91 processors.
 
 config MTD_NAND_PXA3xx
 	tristate "NAND support on PXA3xx and Armada 370/XP"
-	depends on PXA3xx || ARCH_MMP || PLAT_ORION
+	depends on PXA3xx || ARCH_MMP || PLAT_ORION || ARCH_MVEBU
 	help
 	  This enables the driver for the NAND flash device found on
 	  PXA3xx processors (NFCv1) and also on Armada 370/XP (NFCv2).
@@ -433,6 +410,13 @@ config MTD_NAND_ORION
 	  No board specific support is done by this driver, each board
 	  must advertise a platform_device for the driver to attach.
 
+config MTD_NAND_OXNAS
+	tristate "NAND Flash support for Oxford Semiconductor SoC"
+	depends on ARCH_OXNAS || COMPILE_TEST
+	depends on HAS_IOMEM
+	help
+	  This enables the NAND flash controller on Oxford Semiconductor SoCs.
+
 config MTD_NAND_FSL_ELBC
 	tristate "NAND support for Freescale eLBC controllers"
 	depends on FSL_SOC
@@ -445,7 +429,7 @@ config MTD_NAND_FSL_ELBC
 
 config MTD_NAND_FSL_IFC
 	tristate "NAND support for Freescale IFC controller"
-	depends on FSL_SOC || ARCH_LAYERSCAPE
+	depends on FSL_SOC || ARCH_LAYERSCAPE || SOC_LS1021A
 	select FSL_IFC
 	select MEMORY
 	help
@@ -546,13 +530,14 @@ config MTD_NAND_JZ4780
 
 config MTD_NAND_FSMC
 	tristate "Support for NAND on ST Micros FSMC"
+	depends on OF
 	depends on PLAT_SPEAR || ARCH_NOMADIK || ARCH_U8500 || MACH_U300
 	help
 	  Enables support for NAND Flash chips on the ST Microelectronics
 	  Flexible Static Memory Controller (FSMC)
 
 config MTD_NAND_XWAY
-	tristate "Support for NAND on Lantiq XWAY SoC"
+	bool "Support for NAND on Lantiq XWAY SoC"
 	depends on LANTIQ && SOC_TYPE_XWAY
 	help
 	  Enables support for NAND Flash chips on Lantiq XWAY SoCs. NAND is attached
@@ -574,6 +559,7 @@ config MTD_NAND_ARASAN
 
 config MTD_NAND_HISI504
 	tristate "Support for NAND controller on Hisilicon SoC Hip04"
+	depends on ARCH_HISI || COMPILE_TEST
 	depends on HAS_DMA
 	help
 	  Enables support for NAND controller on Hisilicon SoC Hip04.
@@ -587,6 +573,7 @@ config MTD_NAND_QCOM
 
 config MTD_NAND_MTK
 	tristate "Support for NAND controller on MTK SoCs"
+	depends on ARCH_MEDIATEK || COMPILE_TEST
 	depends on HAS_DMA
 	help
 	  Enables support for NAND controller on MTK SoCs.