dialog_copper_zones.cpp 21.4 KB
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 218 219 220 221 222 223 224 225 226 227 228 229 230 231 232 233 234 235 236 237 238 239 240 241 242 243 244 245 246 247 248 249 250 251 252 253 254 255 256 257 258 259 260 261 262 263 264 265 266 267 268 269 270 271 272 273 274 275 276 277 278 279 280 281 282 283 284 285 286 287 288 289 290 291 292 293 294 295 296 297 298 299 300 301 302 303 304 305 306 307 308 309 310 311 312 313 314 315 316 317 318 319 320 321 322 323 324 325 326 327 328 329 330 331 332 333 334 335 336 337 338 339 340 341 342 343 344 345 346 347 348 349 350 351 352 353 354 355 356 357 358 359 360 361 362 363 364 365 366 367 368 369 370 371 372 373 374 375 376 377 378 379 380 381 382 383 384 385 386 387 388 389 390 391 392 393 394 395 396 397 398 399 400 401 402 403 404 405 406 407 408 409 410 411 412 413 414 415 416 417 418 419 420 421 422 423 424 425 426 427 428 429 430 431 432 433 434 435 436 437 438 439 440 441 442 443 444 445 446 447 448 449 450 451 452 453 454 455 456 457 458 459 460 461 462 463 464 465 466 467 468 469 470 471 472 473 474 475 476 477 478 479 480 481 482 483 484 485 486 487 488 489 490 491 492 493 494 495 496 497 498 499 500 501 502 503 504 505 506 507 508 509 510 511 512 513 514 515 516 517 518 519 520 521 522 523 524 525 526 527 528 529 530 531 532 533 534 535 536 537 538 539 540 541 542 543 544 545 546 547 548 549 550 551 552 553 554 555 556 557 558 559 560 561 562 563 564 565 566 567 568 569 570 571 572 573 574 575 576 577 578 579 580 581 582 583 584 585 586 587 588 589 590 591 592 593 594 595 596 597 598 599 600 601 602 603 604 605 606 607 608 609 610 611 612 613 614 615 616 617 618 619 620 621 622 623 624 625 626 627 628 629 630 631 632 633 634 635 636 637 638 639 640 641 642 643 644 645 646 647 648 649 650 651 652 653 654 655 656 657 658 659 660 661 662 663 664 665 666 667 668 669 670 671 672 673 674 675 676 677 678 679 680 681 682 683 684 685 686 687 688 689 690 691
/**
 * @file dialog_copper_zones.cpp
 */

/*
 * This program source code file is part of KiCad, a free EDA CAD application.
 *
 * Copyright (C) 2012 Jean-Pierre Charras, jean-pierre.charras@ujf-grenoble.fr
 * Copyright (C) 2012 SoftPLC Corporation, Dick Hollenbeck <dick@softplc.com>
  * Copyright (C) 1992-2012 KiCad Developers, see AUTHORS.txt for contributors.
 *
 * This program is free software; you can redistribute it and/or
 * modify it under the terms of the GNU General Public License
 * as published by the Free Software Foundation; either version 2
 * of the License, or (at your option) any later version.
 *
 * This program is distributed in the hope that it will be useful,
 * but WITHOUT ANY WARRANTY; without even the implied warranty of
 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
 * GNU General Public License for more details.
 *
 * You should have received a copy of the GNU General Public License
 * along with this program; if not, you may find one here:
 * http://www.gnu.org/licenses/old-licenses/gpl-2.0.html
 * or you may search the http://www.gnu.org website for the version 2 license,
 * or you may write to the Free Software Foundation, Inc.,
 * 51 Franklin Street, Fifth Floor, Boston, MA  02110-1301, USA
 */

#include <wx/wx.h>
#include <fctsys.h>
#include <appl_wxstruct.h>
#include <confirm.h>
#include <PolyLine.h>
#include <pcbnew.h>
#include <wxPcbStruct.h>
#include <zones.h>
#include <base_units.h>

#include <class_zone.h>
#include <class_board.h>
#include <dialog_copper_zones_base.h>

#include <wx/imaglist.h>    // needed for wx/listctrl.h, in wxGTK 2.8.12
#include <wx/listctrl.h>
#include <layers_id_colors_and_visibility.h>


/**
 * Class DIALOG_COPPER_ZONE
 * is the derived class from dialog_copper_zone_frame created by wxFormBuilder
 */
class DIALOG_COPPER_ZONE : public DIALOG_COPPER_ZONE_BASE
{
public:
    DIALOG_COPPER_ZONE( PCB_BASE_FRAME* aParent, ZONE_SETTINGS* aSettings );

private:
    PCB_BASE_FRAME* m_Parent;
    wxConfig*       m_Config;               ///< Current config

    ZONE_EDIT_T     m_OnExitCode;           ///< exit code: ZONE_ABORT if no change,
                                            ///< ZONE_OK if new values accepted
                                            ///< ZONE_EXPORT_VALUES if values are exported to others zones

    ZONE_SETTINGS   m_settings;
    ZONE_SETTINGS*  m_ptr;

    bool            m_NetSortingByPadCount; ///< false = alphabetic sort.
                                            ///< true = pad count sort.

    long            m_NetFiltering;
    std::vector<LAYER_NUM> m_LayerId;       ///< Handle the real layer number from layer
                                            ///< name position in m_LayerSelectionCtrl

    static wxString m_netNameShowFilter;    ///< the filter to show nets (default * "*").
                                            ///< static to keep this pattern for an entire pcbnew session

    /**
     * Function initDialog
     * fills in the dialog controls using the current settings.
     */
    void initDialog();

    void OnButtonOkClick( wxCommandEvent& event );
    void OnButtonCancelClick( wxCommandEvent& event );
    void OnClose( wxCloseEvent& event );
    void OnCornerSmoothingModeChoice( wxCommandEvent& event );

    /**
     * Function AcceptOptions
     * @param aPromptForErrors is true to prompt user on incorrect params.
     * @param aUseExportableSetupOnly is true to use exportable parametres only (used to export this setup to other zones).
     * @return bool - false if incorrect options, true if ok.
     */
    bool AcceptOptions( bool aPromptForErrors, bool aUseExportableSetupOnly = false );

    void OnNetSortingOptionSelected( wxCommandEvent& event );
    void ExportSetupToOtherCopperZones( wxCommandEvent& event );
    void OnPadsInZoneClick( wxCommandEvent& event );
    void OnRunFiltersButtonClick( wxCommandEvent& event );


    void buildAvailableListOfNets();

    /**
     * Function initListNetsParams
     * initializes m_NetSortingByPadCount and m_NetFiltering values
     * according to m_NetDisplayOption selection.
     */
    void initListNetsParams();

    /**
     * Function makeLayerBitmap
     * creates the colored rectangle bitmaps used in the layer selection widget.
     * @param aColor is the color to fill the rectangle with.
     */
    wxBitmap makeLayerBitmap( EDA_COLOR_T aColor );
};


#define LAYER_BITMAP_SIZE_X     20
#define LAYER_BITMAP_SIZE_Y     10

// Initialize static member variables
wxString DIALOG_COPPER_ZONE::m_netNameShowFilter( wxT( "*" ) );


ZONE_EDIT_T InvokeCopperZonesEditor( PCB_BASE_FRAME* aCaller, ZONE_SETTINGS* aSettings )
{
    DIALOG_COPPER_ZONE dlg( aCaller, aSettings );

    ZONE_EDIT_T result = ZONE_EDIT_T( dlg.ShowModal() );
    return result;
}


DIALOG_COPPER_ZONE::DIALOG_COPPER_ZONE( PCB_BASE_FRAME* aParent, ZONE_SETTINGS* aSettings ) :
    DIALOG_COPPER_ZONE_BASE( aParent )
{
    m_Parent = aParent;
    m_Config = wxGetApp().GetSettings();

    m_ptr = aSettings;
    m_settings = *aSettings;

    m_NetSortingByPadCount = true;      // false = alphabetic sort, true = pad count sort
    m_OnExitCode = ZONE_ABORT;

    SetReturnCode( ZONE_ABORT );        // Will be changed on buttons click

    // Fix static text widget minimum width to a suitable value so that
    // resizing the dialog is not necessary when changing the corner smoothing type.
    // Depends on the default text in the widget.
    m_cornerSmoothingTitle->SetMinSize( m_cornerSmoothingTitle->GetSize() );

    initDialog();

    GetSizer()->SetSizeHints( this );
    Center();
}


void DIALOG_COPPER_ZONE::initDialog()
{
    BOARD* board = m_Parent->GetBoard();

    wxString msg;

    if( m_settings.m_Zone_45_Only )
        m_OrientEdgesOpt->SetSelection( 1 );

    m_FillModeCtrl->SetSelection( m_settings.m_FillMode ? 1 : 0 );

    AddUnitSymbol( *m_ClearanceValueTitle, g_UserUnit );
    msg = ReturnStringFromValue( g_UserUnit, m_settings.m_ZoneClearance );
    m_ZoneClearanceCtrl->SetValue( msg );

    AddUnitSymbol( *m_MinThicknessValueTitle, g_UserUnit );
    msg = ReturnStringFromValue( g_UserUnit, m_settings.m_ZoneMinThickness );
    m_ZoneMinThicknessCtrl->SetValue( msg );

    switch( m_settings.GetPadConnection() )
    {
    case THT_THERMAL:               // Thermals only for THT pads
        m_PadInZoneOpt->SetSelection( 2 );
        break;

    case PAD_NOT_IN_ZONE:           // Pads are not covered
        m_PadInZoneOpt->SetSelection( 3 );
        break;

    default:
    case THERMAL_PAD:               // Use thermal relief for pads
        m_PadInZoneOpt->SetSelection( 1 );
        break;

    case PAD_IN_ZONE:               // pads are covered by copper
        m_PadInZoneOpt->SetSelection( 0 );
        break;
    }

    // Antipad and spokes are significant only for thermals
    if( m_settings.GetPadConnection() != THERMAL_PAD &&
        m_settings.GetPadConnection() != THT_THERMAL )
    {
        m_AntipadSizeValue->Enable( false );
        m_CopperWidthValue->Enable( false );
    }
    else
    {
        m_AntipadSizeValue->Enable( true );
        m_CopperWidthValue->Enable( true );
    }

    m_PriorityLevelCtrl->SetValue( m_settings.m_ZonePriority );

    AddUnitSymbol( *m_AntipadSizeText, g_UserUnit );
    AddUnitSymbol( *m_CopperBridgeWidthText, g_UserUnit );
    PutValueInLocalUnits( *m_AntipadSizeValue, m_settings.m_ThermalReliefGap );
    PutValueInLocalUnits( *m_CopperWidthValue, m_settings.m_ThermalReliefCopperBridge );

    m_cornerSmoothingChoice->SetSelection( m_settings.GetCornerSmoothingType() );

    PutValueInLocalUnits( *m_cornerSmoothingCtrl, m_settings.GetCornerRadius() );

    switch( m_settings.m_Zone_HatchingStyle )
    {
    case CPolyLine::NO_HATCH:
        m_OutlineAppearanceCtrl->SetSelection( 0 );
        break;

    case CPolyLine::DIAGONAL_EDGE:
        m_OutlineAppearanceCtrl->SetSelection( 1 );
        break;

    case CPolyLine::DIAGONAL_FULL:
        m_OutlineAppearanceCtrl->SetSelection( 2 );
        break;
    }

    m_ArcApproximationOpt->SetSelection(
        m_settings.m_ArcToSegmentsCount == ARC_APPROX_SEGMENTS_COUNT_HIGHT_DEF ? 1 : 0 );

    // Create one column in m_LayerSelectionCtrl
    wxListItem column0;
    column0.SetId( 0 );
    m_LayerSelectionCtrl->InsertColumn( 0, column0 );
    // Build copper layer list and append to layer widget
    int layerCount = board->GetCopperLayerCount();
    wxImageList* imageList = new wxImageList( LAYER_BITMAP_SIZE_X, LAYER_BITMAP_SIZE_Y );
    m_LayerSelectionCtrl->AssignImageList( imageList, wxIMAGE_LIST_SMALL );
    for( LAYER_NUM ii = FIRST_LAYER; ii < layerCount; ++ii )
    {
        LAYER_NUM layerNumber = LAYER_N_BACK;

        if( layerCount <= 1 || ii < layerCount - 1 )
            layerNumber = ii;
        else if( ii == layerCount - 1 )
            layerNumber = LAYER_N_FRONT;

        m_LayerId.insert( m_LayerId.begin(), layerNumber );

        msg = board->GetLayerName( layerNumber ).Trim();
        EDA_COLOR_T layerColor = board->GetLayerColor( layerNumber );
        imageList->Add( makeLayerBitmap( layerColor ) );
        int itemIndex = m_LayerSelectionCtrl->InsertItem( 0, msg, ii );

        if( m_settings.m_CurrentZone_Layer == layerNumber )
            m_LayerSelectionCtrl->Select( itemIndex );
    }

    m_LayerSelectionCtrl->SetColumnWidth( 0, wxLIST_AUTOSIZE);

    wxString netNameDoNotShowFilter = wxT( "N-*" );
    if( m_Config )
    {
        int opt = m_Config->Read( ZONE_NET_SORT_OPTION_KEY, 1l );
        m_NetDisplayOption->SetSelection( opt );
        m_Config->Read( ZONE_NET_FILTER_STRING_KEY, netNameDoNotShowFilter );
    }
    else
        m_NetDisplayOption->SetSelection( 1 );

    m_ShowNetNameFilter->SetValue( m_netNameShowFilter );
    initListNetsParams();

    // Build list of nets:
    m_DoNotShowNetNameFilter->SetValue( netNameDoNotShowFilter );
    buildAvailableListOfNets();

    wxCommandEvent event;
    OnCornerSmoothingModeChoice( event );
}


void DIALOG_COPPER_ZONE::OnButtonCancelClick( wxCommandEvent& event )
{
    Close( true );
}

void DIALOG_COPPER_ZONE::OnButtonOkClick( wxCommandEvent& event )
{
    m_netNameShowFilter = m_ShowNetNameFilter->GetValue();

    if( AcceptOptions( true ) )
    {
        *m_ptr = m_settings;
        EndModal( ZONE_OK );
    }
}


// called on system close button
void DIALOG_COPPER_ZONE::OnClose( wxCloseEvent& event )
{
    if( m_OnExitCode != ZONE_ABORT )
        *m_ptr = m_settings;

    EndModal( m_OnExitCode );
}


bool DIALOG_COPPER_ZONE::AcceptOptions( bool aPromptForErrors, bool aUseExportableSetupOnly )
{
    switch( m_PadInZoneOpt->GetSelection() )
    {
    case 3:
        // Pads are not covered
        m_settings.SetPadConnection( PAD_NOT_IN_ZONE );
        break;

    case 2:
        // Use thermal relief for THT pads
        m_settings.SetPadConnection( THT_THERMAL );
        break;

    case 1:
        // Use thermal relief for pads
        m_settings.SetPadConnection( THERMAL_PAD );
        break;

    case 0:
        // pads are covered by copper
        m_settings.SetPadConnection( PAD_IN_ZONE );
        break;
    }

    switch( m_OutlineAppearanceCtrl->GetSelection() )
    {
    case 0:
        m_settings.m_Zone_HatchingStyle = CPolyLine::NO_HATCH;
        break;

    case 1:
        m_settings.m_Zone_HatchingStyle = CPolyLine::DIAGONAL_EDGE;
        break;

    case 2:
        m_settings.m_Zone_HatchingStyle = CPolyLine::DIAGONAL_FULL;
        break;
    }

    m_settings.m_ArcToSegmentsCount = m_ArcApproximationOpt->GetSelection() == 1 ?
                                           ARC_APPROX_SEGMENTS_COUNT_HIGHT_DEF :
                                           ARC_APPROX_SEGMENTS_COUNT_LOW_DEF;

    if( m_Config )
    {
        m_Config->Write( ZONE_NET_OUTLINES_HATCH_OPTION_KEY,
                         (long) m_settings.m_Zone_HatchingStyle );
        wxString filter = m_DoNotShowNetNameFilter->GetValue();
        m_Config->Write( ZONE_NET_FILTER_STRING_KEY, filter );
    }

    m_netNameShowFilter = m_ShowNetNameFilter->GetValue();
    m_settings.m_FillMode = (m_FillModeCtrl->GetSelection() == 0) ? 0 : 1;

    wxString txtvalue = m_ZoneClearanceCtrl->GetValue();
    m_settings.m_ZoneClearance = ReturnValueFromString( g_UserUnit, txtvalue );

    // Test if this is a reasonable value for this parameter
    // A too large value can hang Pcbnew
    #define CLEARANCE_MAX_VALUE ZONE_CLEARANCE_MAX_VALUE_MIL*IU_PER_MILS
    if( m_settings.m_ZoneClearance > CLEARANCE_MAX_VALUE )
    {
        wxString msg;
        msg.Printf( _( "Clearance must be smaller than %f\" / %f mm." ),
            ZONE_CLEARANCE_MAX_VALUE_MIL / 1000.0, ZONE_CLEARANCE_MAX_VALUE_MIL * 0.0254 );
        DisplayError( this, msg );
        return false;
    }

    txtvalue = m_ZoneMinThicknessCtrl->GetValue();
    m_settings.m_ZoneMinThickness = ReturnValueFromString( g_UserUnit, txtvalue );

    if( m_settings.m_ZoneMinThickness < (ZONE_THICKNESS_MIN_VALUE_MIL*IU_PER_MILS) )
    {
        wxString msg;
        msg.Printf( _( "Minimum width must be larger than %f\" / %f mm." ),
            ZONE_THICKNESS_MIN_VALUE_MIL / 1000.0, ZONE_THICKNESS_MIN_VALUE_MIL * 0.0254 );
        DisplayError( this, msg );
        return false;
    }

    m_settings.SetCornerSmoothingType( m_cornerSmoothingChoice->GetSelection() );
    txtvalue = m_cornerSmoothingCtrl->GetValue();
    m_settings.SetCornerRadius( ReturnValueFromString( g_UserUnit, txtvalue ) );

    m_settings.m_ZonePriority = m_PriorityLevelCtrl->GetValue();

    if( m_OrientEdgesOpt->GetSelection() == 0 )
        m_settings.m_Zone_45_Only = false;
    else
        m_settings.m_Zone_45_Only = true;

    m_settings.m_ThermalReliefGap = ReturnValueFromTextCtrl( *m_AntipadSizeValue );
    m_settings.m_ThermalReliefCopperBridge = ReturnValueFromTextCtrl( *m_CopperWidthValue );

    if( m_Config )
    {
        ConfigBaseWriteDouble( m_Config, ZONE_CLEARANCE_WIDTH_STRING_KEY,
                               (double) m_settings.m_ZoneClearance / IU_PER_MILS );

        ConfigBaseWriteDouble( m_Config, ZONE_MIN_THICKNESS_WIDTH_STRING_KEY,
            (double) m_settings.m_ZoneMinThickness / IU_PER_MILS );

        ConfigBaseWriteDouble( m_Config, ZONE_THERMAL_RELIEF_GAP_STRING_KEY,
            (double) m_settings.m_ThermalReliefGap / IU_PER_MILS );

        ConfigBaseWriteDouble( m_Config, ZONE_THERMAL_RELIEF_COPPER_WIDTH_STRING_KEY,
            (double) m_settings.m_ThermalReliefCopperBridge / IU_PER_MILS );
    }

    if( m_settings.m_ThermalReliefCopperBridge <= m_settings.m_ZoneMinThickness )
    {
        DisplayError( this,
                     _( "Thermal relief spoke width is smaller than the minimum width." ) );
        return false;
    }

    // If we use only exportable to others zones parameters, exit here:
    if( aUseExportableSetupOnly )
        return true;

    // Get the layer selection for this zone
    int ii = m_LayerSelectionCtrl->GetFirstSelected();

    if( ii < 0 && aPromptForErrors )
    {
        DisplayError( this, _( "No layer selected." ) );
        return false;
    }

    m_settings.m_CurrentZone_Layer = m_LayerId[ii];

    // Get the net name selection for this zone
    ii = m_ListNetNameSelection->GetSelection();

    if( ii < 0 && aPromptForErrors )
    {
        DisplayError( this, _( "No net selected." ) );
        return false;
    }

    if( ii == 0 )   // the not connected option was selected: this is not a good practice: warn:
    {
        if( !IsOK( this, _(
                      "You have chosen the \"not connected\" option. This will create insulated copper islands. Are you sure ?" ) )
            )
            return false;
    }

    wxString net_name = m_ListNetNameSelection->GetString( ii );

    m_settings.m_NetcodeSelection = 0;

    // Search net_code for this net, if a net was selected
    if( m_ListNetNameSelection->GetSelection() > 0 )
    {
        NETINFO_ITEM* net = m_Parent->GetBoard()->FindNet( net_name );
        if( net )
            m_settings.m_NetcodeSelection = net->GetNet();
    }

    return true;
}

void DIALOG_COPPER_ZONE::OnCornerSmoothingModeChoice( wxCommandEvent& event )
{
    int selection = m_cornerSmoothingChoice->GetSelection();

    switch( selection )
    {
    case ZONE_SETTINGS::SMOOTHING_NONE:
        m_cornerSmoothingTitle->Enable( false );
        m_cornerSmoothingCtrl->Enable( false );
        break;
    case ZONE_SETTINGS::SMOOTHING_CHAMFER:
        m_cornerSmoothingTitle->Enable( true );
        m_cornerSmoothingCtrl->Enable( true );
        m_cornerSmoothingTitle->SetLabel( _( "Chamfer distance" ) );
        AddUnitSymbol( *m_cornerSmoothingTitle, g_UserUnit );
        break;
    case ZONE_SETTINGS::SMOOTHING_FILLET:
        m_cornerSmoothingTitle->Enable( true );
        m_cornerSmoothingCtrl->Enable( true );
        m_cornerSmoothingTitle->SetLabel( _( "Fillet radius" ) );
        AddUnitSymbol( *m_cornerSmoothingTitle, g_UserUnit );
        break;
    }
}


void DIALOG_COPPER_ZONE::OnNetSortingOptionSelected( wxCommandEvent& event )
{
    initListNetsParams();
    buildAvailableListOfNets();

    m_netNameShowFilter = m_ShowNetNameFilter->GetValue();
    if( m_Config )
    {
        m_Config->Write( ZONE_NET_SORT_OPTION_KEY, (long) m_NetDisplayOption->GetSelection() );
        wxString Filter = m_DoNotShowNetNameFilter->GetValue();
        m_Config->Write( ZONE_NET_FILTER_STRING_KEY, Filter );
    }
}


void DIALOG_COPPER_ZONE::ExportSetupToOtherCopperZones( wxCommandEvent& event )
{
    if( !AcceptOptions( true, true ) )
        return;

    // Export settings ( but layer and netcode ) to others copper zones
    BOARD* pcb = m_Parent->GetBoard();
    for( int ii = 0; ii < pcb->GetAreaCount(); ii++ )
    {
        ZONE_CONTAINER* zone = pcb->GetArea( ii );

        // Cannot export settings from a copper zone
        // to a zone keepout:
        if( zone->GetIsKeepout() )
            continue;
        m_settings.ExportSetting( *zone, false );  // false = partial export
        m_Parent->OnModify();
    }

    m_OnExitCode = ZONE_EXPORT_VALUES;     // values are exported to others zones
}


void DIALOG_COPPER_ZONE::OnPadsInZoneClick( wxCommandEvent& event )
{
    switch( m_PadInZoneOpt->GetSelection() )
    {
    default:
        m_AntipadSizeValue->Enable( false );
        m_CopperWidthValue->Enable( false );
        break;

    case 2:
    case 1:
        m_AntipadSizeValue->Enable( true );
        m_CopperWidthValue->Enable( true );
        break;
    }
}


void DIALOG_COPPER_ZONE::initListNetsParams()
{
    switch( m_NetDisplayOption->GetSelection() )
    {
    case 0:
        m_NetSortingByPadCount = false;
        m_NetFiltering = false;
        break;

    case 1:
        m_NetSortingByPadCount = true;
        m_NetFiltering = false;
        break;

    case 2:
        m_NetSortingByPadCount = false;
        m_NetFiltering = true;
        break;

    case 3:
        m_NetSortingByPadCount = true;
        m_NetFiltering = true;
        break;
    }
}


void DIALOG_COPPER_ZONE::OnRunFiltersButtonClick( wxCommandEvent& event )
{
    m_netNameShowFilter = m_ShowNetNameFilter->GetValue();

    // Ensure filtered option for nets
    if( m_NetDisplayOption->GetSelection() == 0 )
        m_NetDisplayOption->SetSelection( 2 );
    else if( m_NetDisplayOption->GetSelection() == 1 )
        m_NetDisplayOption->SetSelection( 3 );
    initListNetsParams();
    buildAvailableListOfNets();
}


void DIALOG_COPPER_ZONE::buildAvailableListOfNets()
{
    wxArrayString   listNetName;

    m_Parent->GetBoard()->ReturnSortedNetnamesList( listNetName, m_NetSortingByPadCount );

    if( m_NetFiltering )
    {
        wxString doNotShowFilter = m_DoNotShowNetNameFilter->GetValue();
        wxString ShowFilter = m_ShowNetNameFilter->GetValue();

        for( unsigned ii = 0; ii < listNetName.GetCount(); ii++ )
        {
            if( listNetName[ii].Matches( doNotShowFilter ) )
            {
                listNetName.RemoveAt( ii );
                ii--;
            }
            else if( !listNetName[ii].Matches( ShowFilter ) )
            {
                listNetName.RemoveAt( ii );
                ii--;
            }
        }
    }

    listNetName.Insert( wxT( "<no net>" ), 0 );

    // Ensure currently selected net for the zone is visible, regardless of filters
    int selectedNetListNdx = -1;
    int net_select = m_settings.m_NetcodeSelection;

    if( net_select > 0 )
    {
        NETINFO_ITEM* equipot = m_Parent->GetBoard()->FindNet( net_select );
        if( equipot )
        {
            selectedNetListNdx = listNetName.Index( equipot->GetNetname() );

            if( wxNOT_FOUND == selectedNetListNdx )
            {
                // the currently selected net must *always* be visible.
                listNetName.Insert( equipot->GetNetname(), 0 );
                selectedNetListNdx = 0;
            }
        }
    }
    else if( net_select == 0 )
        selectedNetListNdx = 0;     // SetSelection() on "<no net>"
    else
    {
        // selectedNetListNdx remains -1, no net selected.
    }

    m_ListNetNameSelection->Clear();
    m_ListNetNameSelection->InsertItems( listNetName, 0 );
    m_ListNetNameSelection->SetSelection( 0 );

    if( selectedNetListNdx >= 0 )
    {
        m_ListNetNameSelection->SetSelection( selectedNetListNdx );
        m_ListNetNameSelection->EnsureVisible( selectedNetListNdx );
    }
}


wxBitmap DIALOG_COPPER_ZONE::makeLayerBitmap( EDA_COLOR_T aColor )
{
    wxBitmap    bitmap( LAYER_BITMAP_SIZE_X, LAYER_BITMAP_SIZE_Y );
    wxBrush     brush;
    wxMemoryDC  iconDC;

    iconDC.SelectObject( bitmap );
    brush.SetColour( MakeColour( aColor ) );
    brush.SetStyle( wxSOLID );
    iconDC.SetBrush( brush );
    iconDC.DrawRectangle( 0, 0, LAYER_BITMAP_SIZE_X, LAYER_BITMAP_SIZE_Y );

    return bitmap;
}