updated configs for other boards

u-boot-tree/include/configs/elphel393.h

@@ -22,9 +22,9 @@
 /*#define PHYS_SDRAM_1_SIZE (512 * 1024 * 1024) */
 #define PHYS_SDRAM_1_SIZE (1024 * 1024 * 1024)
 
-#define CONFIG_ZYNQ_SERIAL_UART0 *
-#if 0
-#define CONFIG_ZYNQ_GEM0
+#define CONFIG_ZYNQ_SERIAL_UART0
+#if 1
+//#define CONFIG_ZYNQ_GEM0
 #define CONFIG_ZYNQ_GEM_PHY_ADDR0	0
 #endif
 

u-boot-tree/include/configs/ezynq/ezynq_microzed.h

@@ -78,13 +78,16 @@
 #define CONFIG_EZYNQ_MIO_SDIO_0__PULLUP
 #define CONFIG_EZYNQ_MIO_SDCD_0           46  /* any but 7,8  */
 #define CONFIG_EZYNQ_MIO_SDCD_0__PULLUP
-#define CONFIG_EZYNQ_MIO_SDWP_0           50  /* #any but 7,8  */
-#define CONFIG_EZYNQ_MIO_SDWP_0__PULLUP
+//#define CONFIG_EZYNQ_MIO_SDWP_0           50  /* #any but 7,8  */
+//#define CONFIG_EZYNQ_MIO_SDWP_0__PULLUP
 #define CONFIG_EZYNQ_MIO_UART_1           48  /* #  8+4*N  */
+#define CONFIG_EZYNQ_MIO_UART_0           50  /* #  8+4*N  */
 /* LED will be OFF */
 #define CONFIG_EZYNQ_MIO_INOUT_47   OUT       /* Make output, do not set data. Will be set after debug will be over */
 #define CONFIG_EZYNQ_MIO_GPIO_OUT_7        1  /* Set selected GPIO output to 0/1 */
 
+#define CONFIG_EZYNQ_UART_DEBUG_CHANNEL 0x0
+
 /*
 Red LED - pullup, input - on,
 #define CONFIG_EZYNQ_MIO_INOUT_47   OUT

u-boot-tree/include/configs/zynq_microzed.h

@@ -22,8 +22,8 @@
 #define PHYS_SDRAM_1_SIZE (1024 * 1024 * 1024)
 
 #define CONFIG_ZYNQ_SERIAL_UART1
-#if 0
-#define CONFIG_ZYNQ_GEM0
+#if 1
+//#define CONFIG_ZYNQ_GEM0
 #define CONFIG_ZYNQ_GEM_PHY_ADDR0	0
 #endif
 
@@ -60,7 +60,7 @@
 #undef CONFIG_SYS_TEXT_BASE
 
 #define CONFIG_BOOTDELAY	-1 /* -1 to Disable autoboot */
-#define CONFIG_SYS_PROMPT		"ezynq> "
+#define CONFIG_SYS_PROMPT		"microzed> "
 
 
 #define CONFIG_SYS_SDRAM_BASE		0x00000000 /* Physical start address of SDRAM. _Must_ be 0 here. */

u-boot-tree/include/configs/zynq_zed.h

@@ -21,8 +21,8 @@
 #define PHYS_SDRAM_1_SIZE (512 * 1024 * 1024) 
 
 #define CONFIG_ZYNQ_SERIAL_UART1
-#if 0
-#define CONFIG_ZYNQ_GEM0
+#if 1
+//#define CONFIG_ZYNQ_GEM0
 #define CONFIG_ZYNQ_GEM_PHY_ADDR0	0
 #endif
 
@@ -59,7 +59,7 @@
 #undef CONFIG_SYS_TEXT_BASE
 
 #define CONFIG_BOOTDELAY	-1 /* -1 to Disable autoboot */
-#define CONFIG_SYS_PROMPT		"ezynq> "
+#define CONFIG_SYS_PROMPT		"zedboard> "
 
 
 #define CONFIG_SYS_SDRAM_BASE		0x00000000 /* Physical start address of SDRAM. _Must_ be 0 here. */
@@ -122,10 +122,10 @@
 		"fpga load 0 ${loadbit_addr} ${filesize}\0" \
 	"sdboot=echo Copying Linux from SD to RAM... && " \
 		"mmcinfo && " \
-		"fatload mmc 0 0x3000000 ${kernel_image} && " \
-		"fatload mmc 0 0x2A00000 ${devicetree_image} && " \
+		"fatload mmc 0 0x3A00000 ${kernel_image} && " \
+		"fatload mmc 0 0x3400000 ${devicetree_image} && " \
 		"fatload mmc 0 0x2000000 ${ramdisk_image} && " \
-		"bootm 0x3000000 0x2000000 0x2A00000\0" \
+		"bootm 0x3A00000 0x2000000 0x3400000\0" \
 	"nandboot=echo Copying Linux from NAND flash to RAM... && " \
 		"nand read 0x3000000 0x100000 ${kernel_size} && " \
 		"nand read 0x2A00000 0x600000 ${devicetree_size} && " \