x393_testbench01.tf 77 KB
Newer Older
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21
/*******************************************************************************
 * Module: x393_testbench01
 * Date:2015-02-06  
 * Author: andrey     
 * Description: testbench for the initial x393.v simulation
 *
 * Copyright (c) 2015 <set up in Preferences-Verilog/VHDL Editor-Templates> .
 * x393_testbench01.v is free software; you can redistribute it and/or modify
 * it under the terms of the GNU General Public License as published by
 * the Free Software Foundation, either version 3 of the License, or
 * (at your option) any later version.
 *
 *  x393_testbench01.tf is distributed in the hope that it will be useful,
 * but WITHOUT ANY WARRANTY; without even the implied warranty of
 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
 * GNU General Public License for more details.
 *
 * You should have received a copy of the GNU General Public License
 * along with this program.  If not, see <http://www.gnu.org/licenses/> .
 *******************************************************************************/
`timescale 1ns/1ps
22 23
`include "system_defines.vh"

24
//`define use200Mhz 1
25
//`define DEBUG_FIFO 1
26
`undef WAIT_MRS
27
`define SET_PER_PIN_DELAYS 1 // set individual (including per-DQ pin delays)
28 29
`define PS_PIO_WAIT_COMPLETE 0 // wait until PS PIO module finished transaction before starting a new one
// Disabled already passed test to speedup simulation
30
`define TEST_WRITE_LEVELLING 1
31 32 33
`define TEST_READ_PATTERN 1
`define TEST_WRITE_BLOCK 1
`define TEST_READ_BLOCK 1
34
//`define TESTL_SHORT_SCANLINE 1
35

36
//`define TEST_SCANLINE_WRITE 1
37
    `define TEST_SCANLINE_WRITE_WAIT 1 // wait TEST_SCANLINE_WRITE finished (frame_done)
38
//`define TEST_SCANLINE_READ  1
39
    `define TEST_READ_SHOW  1
40
`define TEST_TILED_WRITE  1
41
    `define TEST_TILED_WRITE_WAIT 1 // wait TEST_SCANLINE_WRITE finished (frame_done)
42

43
`define TEST_TILED_READ  1
44

45 46
`define TEST_TILED_WRITE32  1
`define TEST_TILED_READ32  1
47

48
module  x393_testbench01 #(
49
`include "includes/x393_parameters.vh" // SuppressThisWarning VEditor - not used
50 51 52 53 54 55 56 57 58 59 60 61
`include "includes/x393_simulation_parameters.vh"
)(
);
`ifdef IVERILOG              
//    $display("IVERILOG is defined");
    `include "IVERILOG_INCLUDE.v"
`else
//    $display("IVERILOG is not defined");
    parameter lxtname = "x393.lxt";
`endif
`define DEBUG_WR_SINGLE 1  
`define DEBUG_RD_DATA 1  
62
`include "includes/x393_cur_params_sim.vh" // parameters that may need adjustment, should be before x393_localparams.vh
63
`include "includes/x393_localparams.vh" // SuppressThisWarning VEditor - not used
64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81
  // DDR3 signals
  wire        SDRST;
  wire        SDCLK;  // output
  wire        SDNCLK; // output
  wire [ADDRESS_NUMBER-1:0] SDA;    // output[14:0] 
  wire [ 2:0] SDBA;   // output[2:0] 
  wire        SDWE;   // output
  wire        SDRAS;  // output
  wire        SDCAS;  // output
  wire        SDCKE;  // output
  wire        SDODT;  // output
  wire [15:0] SDD;    // inout[15:0] 
  wire        SDDML;  // inout
  wire        DQSL;   // inout
  wire        NDQSL;  // inout
  wire        SDDMU;  // inout
  wire        DQSU;   // inout
  wire        NDQSU;  // inout
82
  wire        DUMMY_TO_KEEP;  // output to keep PS7 signals from "optimization" // SuppressThisWarning all - not used
Andrey Filippov's avatar
Andrey Filippov committed
83
//  wire        MEMCLK;
84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104
  
  // Simulation signals
  reg [11:0] ARID_IN_r;
  reg [31:0] ARADDR_IN_r;
  reg  [3:0] ARLEN_IN_r;
  reg  [2:0] ARSIZE_IN_r;
  reg  [1:0] ARBURST_IN_r;
  reg [11:0] AWID_IN_r;
  reg [31:0] AWADDR_IN_r;
  reg  [3:0] AWLEN_IN_r;
  reg  [2:0] AWSIZE_IN_r;
  reg  [1:0] AWBURST_IN_r;

  reg [11:0] WID_IN_r;
  reg [31:0] WDATA_IN_r;
  reg [ 3:0] WSTRB_IN_r;
  reg        WLAST_IN_r;
  
  reg [11:0] LAST_ARID; // last issued ARID

  // SuppressWarnings VEditor : assigned in $readmem() system task
105
  wire [SIMUL_AXI_READ_WIDTH-1:0] SIMUL_AXI_ADDR_W;
106 107 108 109 110
  // SuppressWarnings VEditor
  wire        SIMUL_AXI_MISMATCH;
  // SuppressWarnings VEditor
  reg  [31:0] SIMUL_AXI_READ;
  // SuppressWarnings VEditor
111
  reg  [SIMUL_AXI_READ_WIDTH-1:0] SIMUL_AXI_ADDR;
112 113
  // SuppressWarnings VEditor
  reg         SIMUL_AXI_FULL; // some data available
114
  wire        SIMUL_AXI_EMPTY= ~rvalid && rready && (rid==LAST_ARID); //SuppressThisWarning VEditor : may be unused, just for simulation // use it to wait for?
115
  reg  [31:0] registered_rdata; // here read data from tasks goes
116 117
  // SuppressWarnings VEditor
  reg         WAITING_STATUS;   // tasks are waiting for status
118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198

  reg        CLK;
  reg        RST;
  reg        AR_SET_CMD_r;
  wire       AR_READY;

  reg        AW_SET_CMD_r;
  wire       AW_READY;

  reg        W_SET_CMD_r;
  wire       W_READY;

  wire [11:0]  #(AXI_TASK_HOLD) ARID_IN = ARID_IN_r;
  wire [31:0]  #(AXI_TASK_HOLD) ARADDR_IN = ARADDR_IN_r;
  wire  [3:0]  #(AXI_TASK_HOLD) ARLEN_IN = ARLEN_IN_r;
  wire  [2:0]  #(AXI_TASK_HOLD) ARSIZE_IN = ARSIZE_IN_r;
  wire  [1:0]  #(AXI_TASK_HOLD) ARBURST_IN = ARBURST_IN_r;
  wire [11:0]  #(AXI_TASK_HOLD) AWID_IN = AWID_IN_r;
  wire [31:0]  #(AXI_TASK_HOLD) AWADDR_IN = AWADDR_IN_r;
  wire  [3:0]  #(AXI_TASK_HOLD) AWLEN_IN = AWLEN_IN_r;
  wire  [2:0]  #(AXI_TASK_HOLD) AWSIZE_IN = AWSIZE_IN_r;
  wire  [1:0]  #(AXI_TASK_HOLD) AWBURST_IN = AWBURST_IN_r;
  wire [11:0]  #(AXI_TASK_HOLD) WID_IN = WID_IN_r;
  wire [31:0]  #(AXI_TASK_HOLD) WDATA_IN = WDATA_IN_r;
  wire [ 3:0]  #(AXI_TASK_HOLD) WSTRB_IN = WSTRB_IN_r;
  wire         #(AXI_TASK_HOLD) WLAST_IN = WLAST_IN_r;
  wire         #(AXI_TASK_HOLD) AR_SET_CMD = AR_SET_CMD_r;
  wire         #(AXI_TASK_HOLD) AW_SET_CMD = AW_SET_CMD_r;
  wire         #(AXI_TASK_HOLD) W_SET_CMD =  W_SET_CMD_r;

  reg  [3:0] RD_LAG;  // ready signal lag in axi read channel (0 - RDY=1, 1..15 - RDY is asserted N cycles after valid)   
  reg  [3:0] B_LAG;   // ready signal lag in axi arete response channel (0 - RDY=1, 1..15 - RDY is asserted N cycles after valid)   

// Simulation modules interconnection
  wire [11:0] arid;
  wire [31:0] araddr;
  wire [3:0]  arlen;
  wire [2:0]  arsize;
  wire [1:0]  arburst;
  // SuppressWarnings VEditor : assigned in $readmem(14) system task
  wire [3:0]  arcache;
  // SuppressWarnings VEditor : assigned in $readmem() system task
  wire [2:0]  arprot;
  wire        arvalid;
  wire        arready;

  wire [11:0] awid;
  wire [31:0] awaddr;
  wire [3:0]  awlen;
  wire [2:0]  awsize;
  wire [1:0]  awburst;
  // SuppressWarnings VEditor : assigned in $readmem() system task
  wire [3:0]  awcache;
  // SuppressWarnings VEditor : assigned in $readmem() system task
  wire [2:0]  awprot;
  wire        awvalid;
  wire        awready;

  wire [11:0] wid;
  wire [31:0] wdata;
  wire [3:0]  wstrb;
  wire        wlast;
  wire        wvalid;
  wire        wready;
  
  wire [31:0] rdata;
  // SuppressWarnings VEditor : assigned in $readmem() system task
  wire [11:0] rid;
  wire        rlast;
  // SuppressWarnings VEditor : assigned in $readmem() system task
  wire  [1:0] rresp;
  wire        rvalid;
  wire        rready;
  wire        rstb=rvalid && rready;

  // SuppressWarnings VEditor : assigned in $readmem() system task
  wire  [1:0] bresp;
  // SuppressWarnings VEditor : assigned in $readmem() system task
  wire [11:0] bid;
  wire        bvalid;
  wire        bready;
199 200
  integer     NUM_WORDS_READ;
  integer     NUM_WORDS_EXPECTED;
201
  reg  [15:0] ENABLED_CHANNELS = 0; // currently enabled memory channels
202 203
//  integer     SCANLINE_CUR_X;
//  integer     SCANLINE_CUR_Y;
204
  wire AXI_RD_EMPTY=NUM_WORDS_READ==NUM_WORDS_EXPECTED; //SuppressThisWarning VEditor : may be unused, just for simulation
205
  
206 207
  
  
208
  //NUM_XFER_BITS=6
209 210 211
//  localparam       SCANLINE_PAGES_PER_ROW= (WINDOW_WIDTH>>NUM_XFER_BITS)+((WINDOW_WIDTH[NUM_XFER_BITS-1:0]==0)?0:1);
//  localparam       TILES_PER_ROW= (WINDOW_WIDTH/TILE_WIDTH)+  ((WINDOW_WIDTH % TILE_WIDTH==0)?0:1);
//  localparam       TILE_ROWS_PER_WINDOW= ((WINDOW_HEIGHT-1)/TILE_VSTEP) + 1;
212
  
213
//  localparam       TILE_SIZE= TILE_WIDTH*TILE_HEIGHT;
214 215
  
  
216
//  localparam  integer     SCANLINE_FULL_XFER= 1<<NUM_XFER_BITS; // 64 - full page transfer in 8-bursts
217
//  localparam  integer     SCANLINE_LAST_XFER= WINDOW_WIDTH % (1<<NUM_XFER_BITS); // last page transfer size in a row
218
  
219
//  integer ii;
220
//  integer  SCANLINE_XFER_SIZE;
221
always #(CLKIN_PERIOD/2) CLK = ~CLK;
222 223 224 225 226 227 228 229 230 231 232 233 234 235
  initial begin
`ifdef IVERILOG              
    $display("IVERILOG is defined");
`else
    $display("IVERILOG is not defined");
`endif

`ifdef ICARUS              
    $display("ICARUS is defined");
`else
    $display("ICARUS is not defined");
`endif
    $dumpfile(lxtname);
  // SuppressWarnings VEditor : assigned in $readmem() system task
Andrey Filippov's avatar
Andrey Filippov committed
236
    $dumpvars(0,x393_testbench01);
237 238 239 240 241
    CLK =1'b0;
    RST = 1'bx;
    AR_SET_CMD_r = 1'b0;
    AW_SET_CMD_r = 1'b0;
    W_SET_CMD_r = 1'b0;
242 243 244
    #500;
//    $display ("x393_i.ddrc_sequencer_i.phy_cmd_i.phy_top_i.rst=%d",x393_i.ddrc_sequencer_i.phy_cmd_i.phy_top_i.rst);
    #500;
245 246 247 248
    RST = 1'b1;
    NUM_WORDS_EXPECTED =0;
//    #99000; // same as glbl
    #9000; // same as glbl
249
    repeat (20) @(posedge CLK) ;
250
    RST =1'b0;
251 252 253
//set simulation-only parameters   
    axi_set_b_lag(0); //(1);
    axi_set_rd_lag(0);
254
    program_status_all(DEFAULT_STATUS_MODE,'h2a); // mode auto with sequence number increment 
Andrey Filippov's avatar
Andrey Filippov committed
255 256

    enable_memcntrl(1);                 // enable memory controller
Andrey Filippov's avatar
Andrey Filippov committed
257

258
    set_up;
259 260
    axi_set_wbuf_delay(WBUF_DLY_DFLT); //DFLT_WBUF_DELAY - used in synth. code
    
Andrey Filippov's avatar
Andrey Filippov committed
261 262 263 264 265 266 267 268 269 270 271 272
    wait_phase_shifter_ready;
    read_all_status;
// enable output for address/commands to DDR chip    
    enable_cmda(1);
    repeat (16) @(posedge CLK) ;
// remove reset from DDR chip    
    activate_sdrst(0); // was enabled at system reset

    #5000; // actually 500 usec required
    repeat (16) @(posedge CLK) ;
    enable_cke(1);
    repeat (16) @(posedge CLK) ;
Andrey Filippov's avatar
Andrey Filippov committed
273 274 275 276 277 278 279
    
//    enable_memcntrl(1);                 // enable memory controller
    enable_memcntrl_channels(16'h0003); // only channel 0 and 1 are enabled
    configure_channel_priority(0,0);    // lowest priority channel 0
    configure_channel_priority(1,0);    // lowest priority channel 1
    enable_reset_ps_pio(1,0);           // enable, no reset

280
// set MR registers in DDR3 memory, run DCI calibration (long)
281
    wait_ps_pio_ready(DEFAULT_STATUS_MODE, 1); // wait FIFO not half full 
282
    schedule_ps_pio ( // schedule software-control memory operation (may need to check FIFO status first)
Andrey Filippov's avatar
Andrey Filippov committed
283 284
                        INITIALIZE_OFFSET, // input [9:0] seq_addr; // sequence start address
                        0,                 // input [1:0] page;     // buffer page number
285
                        0,                 // input       urgent;   // high priority request (only for competion with other channels, wiil not pass in this FIFO)
286 287 288
                        0,                // input       chn;      // channel buffer to use: 0 - memory read, 1 - memory write
                        `PS_PIO_WAIT_COMPLETE );//  wait_complete; // Do not request a newe transaction from the scheduler until previous memory transaction is finished
                        
289 290
   
`ifdef WAIT_MRS 
291
    wait_ps_pio_done(DEFAULT_STATUS_MODE, 1);
292
`else    
Andrey Filippov's avatar
Andrey Filippov committed
293
    repeat (32) @(posedge CLK) ;  // what delay is needed to be sure? Add to PS_PIO?
294 295
//    first refreshes will be fast (accummulated while waiting)
`endif    
Andrey Filippov's avatar
Andrey Filippov committed
296
    enable_refresh(1);
297
    axi_set_dqs_odelay('h78); //??? dafaults - wrong?
298
    axi_set_dqs_odelay_nominal;
299
    
300 301
`ifdef TEST_WRITE_LEVELLING 
    test_write_levelling;
302
`endif
303
`ifdef TEST_READ_PATTERN
304
    test_read_pattern;
305 306
`endif
`ifdef TEST_WRITE_BLOCK
307
    test_write_block;
308 309
`endif
`ifdef TEST_READ_BLOCK
310
    test_read_block;
311
`endif
312 313 314 315 316 317 318 319 320 321 322 323 324 325 326 327 328 329 330 331 332 333 334 335 336 337 338 339 340 341 342 343 344 345 346 347 348 349 350 351 352 353 354 355 356 357 358 359 360 361 362 363 364 365 366 367
`ifdef TESTL_SHORT_SCANLINE
    test_scanline_write(
        1, // valid: 1 or 3 input            [3:0] channel;
        SCANLINE_EXTRA_PAGES, // input            [1:0] extra_pages;
        1, // input                  wait_done;
        1, //WINDOW_WIDTH,
        WINDOW_HEIGHT,
        WINDOW_X0,
        WINDOW_Y0);
    test_scanline_read (
        1, // valid: 1 or 3 input            [3:0] channel;
        SCANLINE_EXTRA_PAGES, // input            [1:0] extra_pages;
        1, // input                  show_data;
        1, // WINDOW_WIDTH,
        WINDOW_HEIGHT,
        WINDOW_X0,
        WINDOW_Y0);

    test_scanline_write(
        1, // valid: 1 or 3 input            [3:0] channel;
        SCANLINE_EXTRA_PAGES, // input            [1:0] extra_pages;
        1, // input                  wait_done;
        2, //WINDOW_WIDTH,
        WINDOW_HEIGHT,
        WINDOW_X0,
        WINDOW_Y0);
    test_scanline_read (
        1, // valid: 1 or 3 input            [3:0] channel;
        SCANLINE_EXTRA_PAGES, // input            [1:0] extra_pages;
        1, // input                  show_data;
        2, // WINDOW_WIDTH,
        WINDOW_HEIGHT,
        WINDOW_X0,
        WINDOW_Y0);

    test_scanline_write(
        1, // valid: 1 or 3 input            [3:0] channel;
        SCANLINE_EXTRA_PAGES, // input            [1:0] extra_pages;
        1, // input                  wait_done;
        3, //WINDOW_WIDTH,
        WINDOW_HEIGHT,
        WINDOW_X0,
        WINDOW_Y0);
    test_scanline_read (
        1, // valid: 1 or 3 input            [3:0] channel;
        SCANLINE_EXTRA_PAGES, // input            [1:0] extra_pages;
        1, // input                  show_data;
        3, // WINDOW_WIDTH,
        WINDOW_HEIGHT,
        WINDOW_X0,
        WINDOW_Y0);



`endif

368
`ifdef TEST_SCANLINE_WRITE
369 370 371
    test_scanline_write(
        1, // valid: 1 or 3 input            [3:0] channel;
        SCANLINE_EXTRA_PAGES, // input            [1:0] extra_pages;
372 373 374 375 376 377
        1, // input                  wait_done;
        WINDOW_WIDTH,
        WINDOW_HEIGHT,
        WINDOW_X0,
        WINDOW_Y0);
        
378
`endif
379
`ifdef TEST_SCANLINE_READ
380 381 382
    test_scanline_read (
        1, // valid: 1 or 3 input            [3:0] channel;
        SCANLINE_EXTRA_PAGES, // input            [1:0] extra_pages;
383 384 385 386 387 388
        1, // input                  show_data;
        WINDOW_WIDTH,
        WINDOW_HEIGHT,
        WINDOW_X0,
        WINDOW_Y0);
        
389 390
`endif

391
`ifdef TEST_TILED_WRITE
392 393 394 395 396
    test_tiled_write (
         2,                 // [3:0] channel;
         0,                 //       byte32;
         TILED_KEEP_OPEN,   //       keep_open;
         TILED_EXTRA_PAGES, //       extra_pages;
397 398 399 400 401 402 403 404
         1,                //       wait_done;
        WINDOW_WIDTH,
        WINDOW_HEIGHT,
        WINDOW_X0,
        WINDOW_Y0,
        TILE_WIDTH,
        TILE_HEIGHT,
        TILE_VSTEP);
405 406
`endif

407
`ifdef TEST_TILED_READ
408
    test_tiled_read (
409 410 411 412 413 414 415 416 417 418 419 420 421
        2,                 // [3:0] channel;
        0,                 //       byte32;
        TILED_KEEP_OPEN,   //       keep_open;
        TILED_EXTRA_PAGES, //       extra_pages;
        1,                 //       show_data;
        WINDOW_WIDTH,
        WINDOW_HEIGHT,
        WINDOW_X0,
        WINDOW_Y0,
        TILE_WIDTH,
        TILE_HEIGHT,
        TILE_VSTEP);
         
422 423
`endif

424 425
`ifdef TEST_TILED_WRITE32
    test_tiled_write (
426 427 428 429 430 431 432 433 434 435 436 437
        4, // 2,                 // [3:0] channel;
        1,                 //       byte32;
        TILED_KEEP_OPEN,   //       keep_open;
        TILED_EXTRA_PAGES, //       extra_pages;
        1,                 //       wait_done;
        WINDOW_WIDTH,
        WINDOW_HEIGHT,
        WINDOW_X0,
        WINDOW_Y0,
        TILE_WIDTH,
        TILE_HEIGHT,
        TILE_VSTEP);
438 439 440 441
`endif

`ifdef TEST_TILED_READ32
    test_tiled_read (
442 443 444 445 446 447 448 449 450 451 452 453
        4, //2,                 // [3:0] channel;
        1,                 //       byte32;
        TILED_KEEP_OPEN,   //       keep_open;
        TILED_EXTRA_PAGES, //       extra_pages;
        1,                 //       show_data;
        WINDOW_WIDTH,
        WINDOW_HEIGHT,
        WINDOW_X0,
        WINDOW_Y0,
        TILE_WIDTH,
        TILE_HEIGHT,
        TILE_VSTEP);
454
`endif
455
  #20000;
456
  $finish;
457 458 459 460
end
// protect from never end
  initial begin
//  #10000000;
461
     #200000;
462
//     #42000;
463
//   #100000;
464
//  #60000;
465 466 467 468 469 470 471 472 473 474 475 476 477 478 479 480 481 482 483 484 485 486 487 488 489 490 491 492 493 494 495 496 497 498 499 500 501 502 503 504 505 506 507 508 509 510 511 512 513 514 515 516 517 518 519
    $display("finish testbench 2");
  $finish;
  end



assign x393_i.ps7_i.FCLKCLK=        {4{CLK}};
assign x393_i.ps7_i.FCLKRESETN=     {RST,~RST,RST,~RST};
// Read address
assign x393_i.ps7_i.MAXIGP0ARADDR=  araddr;
assign x393_i.ps7_i.MAXIGP0ARVALID= arvalid;
assign arready=                            x393_i.ps7_i.MAXIGP0ARREADY;
assign x393_i.ps7_i.MAXIGP0ARID=    arid; 
assign x393_i.ps7_i.MAXIGP0ARLEN=   arlen;
assign x393_i.ps7_i.MAXIGP0ARSIZE=  arsize[1:0]; // arsize[2] is not used
assign x393_i.ps7_i.MAXIGP0ARBURST= arburst;
// Read data
assign rdata=                              x393_i.ps7_i.MAXIGP0RDATA; 
assign rvalid=                             x393_i.ps7_i.MAXIGP0RVALID;
assign x393_i.ps7_i.MAXIGP0RREADY=  rready;
assign rid=                                x393_i.ps7_i.MAXIGP0RID;
assign rlast=                              x393_i.ps7_i.MAXIGP0RLAST;
assign rresp=                              x393_i.ps7_i.MAXIGP0RRESP;
// Write address
assign x393_i.ps7_i.MAXIGP0AWADDR=  awaddr;
assign x393_i.ps7_i.MAXIGP0AWVALID= awvalid;

assign awready=                            x393_i.ps7_i.MAXIGP0AWREADY;

//assign awready= AWREADY_AAAA;
assign x393_i.ps7_i.MAXIGP0AWID=awid;

      // SuppressWarnings VEditor all
//  wire [ 1:0] AWLOCK;
      // SuppressWarnings VEditor all
//  wire [ 3:0] AWCACHE;
      // SuppressWarnings VEditor all
//  wire [ 2:0] AWPROT;
assign x393_i.ps7_i.MAXIGP0AWLEN=   awlen;
assign x393_i.ps7_i.MAXIGP0AWSIZE=  awsize[1:0]; // awsize[2] is not used
assign x393_i.ps7_i.MAXIGP0AWBURST= awburst;
      // SuppressWarnings VEditor all
//  wire [ 3:0] AWQOS;
// Write data
assign x393_i.ps7_i.MAXIGP0WDATA=   wdata;
assign x393_i.ps7_i.MAXIGP0WVALID=  wvalid;
assign wready=                             x393_i.ps7_i.MAXIGP0WREADY;
assign x393_i.ps7_i.MAXIGP0WID=     wid;
assign x393_i.ps7_i.MAXIGP0WLAST=   wlast;
assign x393_i.ps7_i.MAXIGP0WSTRB=   wstrb;
// Write responce
assign bvalid=                             x393_i.ps7_i.MAXIGP0BVALID;
assign x393_i.ps7_i.MAXIGP0BREADY=  bready;
assign bid=                                x393_i.ps7_i.MAXIGP0BID;
assign bresp=                              x393_i.ps7_i.MAXIGP0BRESP;
520
//TODO: See how to show problems in include files opened in the editor (test all top *.v files that have it)
521 522 523 524 525 526
// Top module under test
    x393 #(
        .MCONTR_WR_MASK                    (MCONTR_WR_MASK),
        .MCONTR_RD_MASK                    (MCONTR_RD_MASK),
        .MCONTR_CMD_WR_ADDR                (MCONTR_CMD_WR_ADDR),
        .MCONTR_BUF0_RD_ADDR               (MCONTR_BUF0_RD_ADDR),
527 528
        .MCONTR_BUF0_WR_ADDR               (MCONTR_BUF0_WR_ADDR),
        .MCONTR_BUF1_RD_ADDR               (MCONTR_BUF1_RD_ADDR),
529 530
        .MCONTR_BUF1_WR_ADDR               (MCONTR_BUF1_WR_ADDR),
        .MCONTR_BUF2_RD_ADDR               (MCONTR_BUF2_RD_ADDR),
531 532
        .MCONTR_BUF2_WR_ADDR               (MCONTR_BUF2_WR_ADDR),
        .MCONTR_BUF3_RD_ADDR               (MCONTR_BUF3_RD_ADDR),
533 534
        .MCONTR_BUF3_WR_ADDR               (MCONTR_BUF3_WR_ADDR),
        .MCONTR_BUF4_RD_ADDR               (MCONTR_BUF4_RD_ADDR),
535
        .MCONTR_BUF4_WR_ADDR               (MCONTR_BUF4_WR_ADDR),
536 537 538 539 540 541 542
        .CONTROL_ADDR                      (CONTROL_ADDR),
        .CONTROL_ADDR_MASK                 (CONTROL_ADDR_MASK),
        .STATUS_ADDR                       (STATUS_ADDR),
        .STATUS_ADDR_MASK                  (STATUS_ADDR_MASK),
        .AXI_WR_ADDR_BITS                  (AXI_WR_ADDR_BITS),
        .AXI_RD_ADDR_BITS                  (AXI_RD_ADDR_BITS),
        .STATUS_DEPTH                      (STATUS_DEPTH),
543 544 545 546 547 548 549 550 551 552 553 554 555 556 557 558 559 560 561 562 563 564 565 566 567 568 569 570 571 572 573 574 575 576 577 578 579 580 581 582 583 584 585 586 587 588 589 590 591 592 593 594 595 596 597 598 599 600 601 602 603 604 605 606 607 608 609 610 611 612 613 614 615 616 617 618 619 620 621 622 623 624 625 626 627 628 629 630 631 632 633 634 635 636 637
        .DLY_LD                            (DLY_LD),
        .DLY_LD_MASK                       (DLY_LD_MASK),
        .MCONTR_PHY_0BIT_ADDR              (MCONTR_PHY_0BIT_ADDR),
        .MCONTR_PHY_0BIT_ADDR_MASK         (MCONTR_PHY_0BIT_ADDR_MASK),
        .MCONTR_PHY_0BIT_DLY_SET           (MCONTR_PHY_0BIT_DLY_SET),
        .MCONTR_PHY_0BIT_CMDA_EN           (MCONTR_PHY_0BIT_CMDA_EN),
        .MCONTR_PHY_0BIT_SDRST_ACT         (MCONTR_PHY_0BIT_SDRST_ACT),
        .MCONTR_PHY_0BIT_CKE_EN            (MCONTR_PHY_0BIT_CKE_EN),
        .MCONTR_PHY_0BIT_DCI_RST           (MCONTR_PHY_0BIT_DCI_RST),
        .MCONTR_PHY_0BIT_DLY_RST           (MCONTR_PHY_0BIT_DLY_RST),
        .MCONTR_TOP_0BIT_ADDR              (MCONTR_TOP_0BIT_ADDR),
        .MCONTR_TOP_0BIT_ADDR_MASK         (MCONTR_TOP_0BIT_ADDR_MASK),
        .MCONTR_TOP_0BIT_MCONTR_EN         (MCONTR_TOP_0BIT_MCONTR_EN),
        .MCONTR_TOP_0BIT_REFRESH_EN        (MCONTR_TOP_0BIT_REFRESH_EN),
        .MCONTR_PHY_16BIT_ADDR             (MCONTR_PHY_16BIT_ADDR),
        .MCONTR_PHY_16BIT_ADDR_MASK        (MCONTR_PHY_16BIT_ADDR_MASK),
        .MCONTR_PHY_16BIT_PATTERNS         (MCONTR_PHY_16BIT_PATTERNS),
        .MCONTR_PHY_16BIT_PATTERNS_TRI     (MCONTR_PHY_16BIT_PATTERNS_TRI),
        .MCONTR_PHY_16BIT_WBUF_DELAY       (MCONTR_PHY_16BIT_WBUF_DELAY),
        .MCONTR_PHY_16BIT_EXTRA            (MCONTR_PHY_16BIT_EXTRA),
        .MCONTR_PHY_STATUS_CNTRL           (MCONTR_PHY_STATUS_CNTRL),
        .MCONTR_ARBIT_ADDR                 (MCONTR_ARBIT_ADDR),
        .MCONTR_ARBIT_ADDR_MASK            (MCONTR_ARBIT_ADDR_MASK),
        .MCONTR_TOP_16BIT_ADDR             (MCONTR_TOP_16BIT_ADDR),
        .MCONTR_TOP_16BIT_ADDR_MASK        (MCONTR_TOP_16BIT_ADDR_MASK),
        .MCONTR_TOP_16BIT_CHN_EN           (MCONTR_TOP_16BIT_CHN_EN),
        .MCONTR_TOP_16BIT_REFRESH_PERIOD   (MCONTR_TOP_16BIT_REFRESH_PERIOD),
        .MCONTR_TOP_16BIT_REFRESH_ADDRESS  (MCONTR_TOP_16BIT_REFRESH_ADDRESS),
        .MCONTR_TOP_16BIT_STATUS_CNTRL     (MCONTR_TOP_16BIT_STATUS_CNTRL),
        .MCONTR_PHY_STATUS_REG_ADDR        (MCONTR_PHY_STATUS_REG_ADDR),
        .MCONTR_TOP_STATUS_REG_ADDR        (MCONTR_TOP_STATUS_REG_ADDR),
        .CHNBUF_READ_LATENCY               (CHNBUF_READ_LATENCY),
        .DFLT_DQS_PATTERN                  (DFLT_DQS_PATTERN),
        .DFLT_DQM_PATTERN                  (DFLT_DQM_PATTERN),
        .DFLT_DQ_TRI_ON_PATTERN            (DFLT_DQ_TRI_ON_PATTERN),
        .DFLT_DQ_TRI_OFF_PATTERN           (DFLT_DQ_TRI_OFF_PATTERN),
        .DFLT_DQS_TRI_ON_PATTERN           (DFLT_DQS_TRI_ON_PATTERN),
        .DFLT_DQS_TRI_OFF_PATTERN          (DFLT_DQS_TRI_OFF_PATTERN),
        .DFLT_WBUF_DELAY                   (DFLT_WBUF_DELAY),
        .DFLT_INV_CLK_DIV                  (DFLT_INV_CLK_DIV),
        .DFLT_CHN_EN                       (DFLT_CHN_EN),
        .DFLT_REFRESH_ADDR                 (DFLT_REFRESH_ADDR),
        .DFLT_REFRESH_PERIOD               (DFLT_REFRESH_PERIOD),
        .ADDRESS_NUMBER                    (ADDRESS_NUMBER),
        .COLADDR_NUMBER                    (COLADDR_NUMBER),
        .PHASE_WIDTH                       (PHASE_WIDTH),
        .SLEW_DQ                           (SLEW_DQ),
        .SLEW_DQS                          (SLEW_DQS),
        .SLEW_CMDA                         (SLEW_CMDA),
        .SLEW_CLK                          (SLEW_CLK),
        .IBUF_LOW_PWR                      (IBUF_LOW_PWR),
        .REFCLK_FREQUENCY                  (REFCLK_FREQUENCY),
        .HIGH_PERFORMANCE_MODE             (HIGH_PERFORMANCE_MODE),
        .CLKIN_PERIOD                      (CLKIN_PERIOD),
        .CLKFBOUT_MULT                     (CLKFBOUT_MULT),
        .CLKFBOUT_MULT_REF                 (CLKFBOUT_MULT_REF),
        .CLKFBOUT_DIV_REF                  (CLKFBOUT_DIV_REF),
        .DIVCLK_DIVIDE                     (DIVCLK_DIVIDE),
        .CLKFBOUT_PHASE                    (CLKFBOUT_PHASE),
        .SDCLK_PHASE                       (SDCLK_PHASE),
        .CLK_PHASE                         (CLK_PHASE),
        .CLK_DIV_PHASE                     (CLK_DIV_PHASE),
        .MCLK_PHASE                        (MCLK_PHASE),
        .REF_JITTER1                       (REF_JITTER1),
        .SS_EN                             (SS_EN),
        .SS_MODE                           (SS_MODE),
        .SS_MOD_PERIOD                     (SS_MOD_PERIOD),
        .CMD_PAUSE_BITS                    (CMD_PAUSE_BITS),
        .CMD_DONE_BIT                      (CMD_DONE_BIT),
        .NUM_CYCLES_LOW_BIT                (NUM_CYCLES_LOW_BIT),
        .NUM_CYCLES_00                     (NUM_CYCLES_00),
        .NUM_CYCLES_01                     (NUM_CYCLES_01),
        .NUM_CYCLES_02                     (NUM_CYCLES_02),
        .NUM_CYCLES_03                     (NUM_CYCLES_03),
        .NUM_CYCLES_04                     (NUM_CYCLES_04),
        .NUM_CYCLES_05                     (NUM_CYCLES_05),
        .NUM_CYCLES_06                     (NUM_CYCLES_06),
        .NUM_CYCLES_07                     (NUM_CYCLES_07),
        .NUM_CYCLES_08                     (NUM_CYCLES_08),
        .NUM_CYCLES_09                     (NUM_CYCLES_09),
        .NUM_CYCLES_10                     (NUM_CYCLES_10),
        .NUM_CYCLES_11                     (NUM_CYCLES_11),
        .NUM_CYCLES_12                     (NUM_CYCLES_12),
        .NUM_CYCLES_13                     (NUM_CYCLES_13),
        .NUM_CYCLES_14                     (NUM_CYCLES_14),
        .NUM_CYCLES_15                     (NUM_CYCLES_15),
        .MCNTRL_PS_ADDR                    (MCNTRL_PS_ADDR),
        .MCNTRL_PS_MASK                    (MCNTRL_PS_MASK),
        .MCNTRL_PS_STATUS_REG_ADDR         (MCNTRL_PS_STATUS_REG_ADDR),
        .MCNTRL_PS_EN_RST                  (MCNTRL_PS_EN_RST),
        .MCNTRL_PS_CMD                     (MCNTRL_PS_CMD),
        .MCNTRL_PS_STATUS_CNTRL            (MCNTRL_PS_STATUS_CNTRL),
        .NUM_XFER_BITS                     (NUM_XFER_BITS),
        .FRAME_WIDTH_BITS                  (FRAME_WIDTH_BITS),
        .FRAME_HEIGHT_BITS                 (FRAME_HEIGHT_BITS),
638
        .MCNTRL_SCANLINE_CHN1_ADDR         (MCNTRL_SCANLINE_CHN1_ADDR),
639 640 641 642 643 644 645 646 647
        .MCNTRL_SCANLINE_CHN3_ADDR         (MCNTRL_SCANLINE_CHN3_ADDR),
        .MCNTRL_SCANLINE_MASK              (MCNTRL_SCANLINE_MASK),
        .MCNTRL_SCANLINE_MODE              (MCNTRL_SCANLINE_MODE),
        .MCNTRL_SCANLINE_STATUS_CNTRL      (MCNTRL_SCANLINE_STATUS_CNTRL),
        .MCNTRL_SCANLINE_STARTADDR         (MCNTRL_SCANLINE_STARTADDR),
        .MCNTRL_SCANLINE_FRAME_FULL_WIDTH  (MCNTRL_SCANLINE_FRAME_FULL_WIDTH),
        .MCNTRL_SCANLINE_WINDOW_WH         (MCNTRL_SCANLINE_WINDOW_WH),
        .MCNTRL_SCANLINE_WINDOW_X0Y0       (MCNTRL_SCANLINE_WINDOW_X0Y0),
        .MCNTRL_SCANLINE_WINDOW_STARTXY    (MCNTRL_SCANLINE_WINDOW_STARTXY),
648
        .MCNTRL_SCANLINE_STATUS_REG_CHN1_ADDR   (MCNTRL_SCANLINE_STATUS_REG_CHN1_ADDR),
649 650
        .MCNTRL_SCANLINE_STATUS_REG_CHN3_ADDR   (MCNTRL_SCANLINE_STATUS_REG_CHN3_ADDR),
        .MCNTRL_SCANLINE_PENDING_CNTR_BITS (MCNTRL_SCANLINE_PENDING_CNTR_BITS),
651
        .MCNTRL_SCANLINE_FRAME_PAGE_RESET  (MCNTRL_SCANLINE_FRAME_PAGE_RESET),
652 653
        .MAX_TILE_WIDTH                    (MAX_TILE_WIDTH),
        .MAX_TILE_HEIGHT                   (MAX_TILE_HEIGHT),
654
        .MCNTRL_TILED_CHN2_ADDR            (MCNTRL_TILED_CHN2_ADDR),
655 656 657 658 659 660 661 662 663
        .MCNTRL_TILED_CHN4_ADDR            (MCNTRL_TILED_CHN4_ADDR),
        .MCNTRL_TILED_MASK                 (MCNTRL_TILED_MASK),
        .MCNTRL_TILED_MODE                 (MCNTRL_TILED_MODE),
        .MCNTRL_TILED_STATUS_CNTRL         (MCNTRL_TILED_STATUS_CNTRL),
        .MCNTRL_TILED_STARTADDR            (MCNTRL_TILED_STARTADDR),
        .MCNTRL_TILED_FRAME_FULL_WIDTH     (MCNTRL_TILED_FRAME_FULL_WIDTH),
        .MCNTRL_TILED_WINDOW_WH            (MCNTRL_TILED_WINDOW_WH),
        .MCNTRL_TILED_WINDOW_X0Y0          (MCNTRL_TILED_WINDOW_X0Y0),
        .MCNTRL_TILED_WINDOW_STARTXY       (MCNTRL_TILED_WINDOW_STARTXY),
664 665
        .MCNTRL_TILED_TILE_WHS             (MCNTRL_TILED_TILE_WHS),
        .MCNTRL_TILED_STATUS_REG_CHN2_ADDR (MCNTRL_TILED_STATUS_REG_CHN2_ADDR),
666 667 668 669 670 671
        .MCNTRL_TILED_STATUS_REG_CHN4_ADDR (MCNTRL_TILED_STATUS_REG_CHN4_ADDR),
        .MCNTRL_TILED_PENDING_CNTR_BITS    (MCNTRL_TILED_PENDING_CNTR_BITS),
        .MCNTRL_TILED_FRAME_PAGE_RESET     (MCNTRL_TILED_FRAME_PAGE_RESET),
        .BUFFER_DEPTH32                    (BUFFER_DEPTH32),
        .MCNTRL_TEST01_ADDR                 (MCNTRL_TEST01_ADDR),
        .MCNTRL_TEST01_MASK                 (MCNTRL_TEST01_MASK),
672 673
        .MCNTRL_TEST01_CHN1_MODE            (MCNTRL_TEST01_CHN1_MODE),
        .MCNTRL_TEST01_CHN1_STATUS_CNTRL    (MCNTRL_TEST01_CHN1_STATUS_CNTRL),
674 675 676 677 678 679
        .MCNTRL_TEST01_CHN2_MODE            (MCNTRL_TEST01_CHN2_MODE),
        .MCNTRL_TEST01_CHN2_STATUS_CNTRL    (MCNTRL_TEST01_CHN2_STATUS_CNTRL),
        .MCNTRL_TEST01_CHN3_MODE            (MCNTRL_TEST01_CHN3_MODE),
        .MCNTRL_TEST01_CHN3_STATUS_CNTRL    (MCNTRL_TEST01_CHN3_STATUS_CNTRL),
        .MCNTRL_TEST01_CHN4_MODE            (MCNTRL_TEST01_CHN4_MODE),
        .MCNTRL_TEST01_CHN4_STATUS_CNTRL    (MCNTRL_TEST01_CHN4_STATUS_CNTRL),
680
        .MCNTRL_TEST01_STATUS_REG_CHN1_ADDR (MCNTRL_TEST01_STATUS_REG_CHN1_ADDR),
681 682
        .MCNTRL_TEST01_STATUS_REG_CHN2_ADDR (MCNTRL_TEST01_STATUS_REG_CHN2_ADDR),
        .MCNTRL_TEST01_STATUS_REG_CHN3_ADDR (MCNTRL_TEST01_STATUS_REG_CHN3_ADDR),
683
        .MCNTRL_TEST01_STATUS_REG_CHN4_ADDR (MCNTRL_TEST01_STATUS_REG_CHN4_ADDR)
684 685 686 687 688 689 690 691 692 693 694 695 696 697 698 699 700 701
    ) x393_i (
        .SDRST   (SDRST), // DDR3 reset (active low)
        .SDCLK   (SDCLK), // output 
        .SDNCLK  (SDNCLK), // outputread_and_wait(BASEADDR_STATUS)
        .SDA     (SDA[14:0]), // output[14:0] 
        .SDBA    (SDBA[2:0]), // output[2:0] 
        .SDWE    (SDWE), // output
        .SDRAS   (SDRAS), // output
        .SDCAS   (SDCAS), // output
        .SDCKE   (SDCKE), // output
        .SDODT   (SDODT), // output
        .SDD     (SDD[15:0]), // inout[15:0] 
        .SDDML   (SDDML), // inout
        .DQSL    (DQSL), // inout
        .NDQSL   (NDQSL), // inout
        .SDDMU   (SDDMU), // inout
        .DQSU    (DQSU), // inout
        .NDQSU   (NDQSU), // inout
Andrey Filippov's avatar
Andrey Filippov committed
702 703
        .DUMMY_TO_KEEP(DUMMY_TO_KEEP)  // to keep PS7 signals from "optimization"
//      ,.MEMCLK  (MEMCLK)
704 705 706 707 708 709 710 711 712 713 714 715 716 717 718 719 720 721 722 723 724 725 726 727 728 729 730 731 732 733 734 735 736 737 738 739 740 741 742 743 744 745 746 747 748 749 750 751 752 753 754 755 756 757 758 759 760 761 762 763 764 765 766 767 768 769 770 771 772 773 774 775 776 777 778 779 780 781 782 783 784 785 786 787 788 789 790 791 792 793 794 795 796 797 798 799 800 801 802 803 804 805 806 807 808 809 810 811 812 813 814 815 816 817 818 819 820 821 822 823 824 825 826 827 828 829 830 831 832 833 834 835 836 837 838 839 840 841 842 843 844 845 846 847 848 849 850 851 852 853 854 855 856 857 858 859 860 861 862 863 864 865 866 867 868 869 870 871 872 873 874 875 876 877 878 879 880 881 882 883 884 885 886 887 888 889 890 891 892 893 894 895 896 897 898 899 900 901 902 903 904 905 906 907 908 909 910 911 912 913 914 915 916 917 918 919 920 921 922 923 924 925 926 927 928 929 930 931 932 933 934 935 936 937 938 939 940 941 942 943 944 945 946 947 948 949 950 951 952 953 954 955 956 957 958 959 960 961 962 963 964 965 966 967 968 969 970 971 972 973 974 975 976 977 978 979 980 981 982 983 984 985 986 987 988 989 990 991 992 993 994 995 996 997 998 999
    );
// Micron DDR3 memory model
    /* Instance of Micron DDR3 memory model */
    ddr3 #(
        .TCK_MIN             (2500), 
        .TJIT_PER            (100),
        .TJIT_CC             (200),
        .TERR_2PER           (147),
        .TERR_3PER           (175),
        .TERR_4PER           (194),
        .TERR_5PER           (209),
        .TERR_6PER           (222),
        .TERR_7PER           (232),
        .TERR_8PER           (241),
        .TERR_9PER           (249),
        .TERR_10PER          (257),
        .TERR_11PER          (263),
        .TERR_12PER          (269),
        .TDS                 (125),
        .TDH                 (150),
        .TDQSQ               (200),
        .TDQSS               (0.25),
        .TDSS                (0.20),
        .TDSH                (0.20),
        .TDQSCK              (400),
        .TQSH                (0.38),
        .TQSL                (0.38),
        .TDIPW               (600),
        .TIPW                (900),
        .TIS                 (350),
        .TIH                 (275),
        .TRAS_MIN            (37500),
        .TRC                 (52500),
        .TRCD                (15000),
        .TRP                 (15000),
        .TXP                 (7500),
        .TCKE                (7500),
        .TAON                (400),
        .TWLS                (325),
        .TWLH                (325),
        .TWLO                (9000),
        .TAA_MIN             (15000),
        .CL_TIME             (15000),
        .TDQSCK_DLLDIS       (400),
        .TRRD                (10000),
        .TFAW                (40000),
        .CL_MIN              (5),
        .CL_MAX              (14),
        .AL_MIN              (0),
        .AL_MAX              (2),
        .WR_MIN              (5),
        .WR_MAX              (16),
        .BL_MIN              (4),
        .BL_MAX              (8),
        .CWL_MIN             (5),
        .CWL_MAX             (10),
        .TCK_MAX             (3300),
        .TCH_AVG_MIN         (0.47),
        .TCL_AVG_MIN         (0.47),
        .TCH_AVG_MAX         (0.53),
        .TCL_AVG_MAX         (0.53),
        .TCH_ABS_MIN         (0.43),
        .TCL_ABS_MIN         (0.43),
        .TCKE_TCK            (3),
        .TAA_MAX             (20000),
        .TQH                 (0.38),
        .TRPRE               (0.90),
        .TRPST               (0.30),
        .TDQSH               (0.45),
        .TDQSL               (0.45),
        .TWPRE               (0.90),
        .TWPST               (0.30),
        .TCCD                (4),
        .TCCD_DG             (2),
        .TRAS_MAX            (60e9),
        .TWR                 (15000),
        .TMRD                (4),
        .TMOD                (15000),
        .TMOD_TCK            (12),
        .TRRD_TCK            (4),
        .TRRD_DG             (3000),
        .TRRD_DG_TCK         (2),
        .TRTP                (7500),
        .TRTP_TCK            (4),
        .TWTR                (7500),
        .TWTR_DG             (3750),
        .TWTR_TCK            (4),
        .TWTR_DG_TCK         (2),
        .TDLLK               (512),
        .TRFC_MIN            (260000),
        .TRFC_MAX            (70200000),
        .TXP_TCK             (3),
        .TXPDLL              (24000),
        .TXPDLL_TCK          (10),
        .TACTPDEN            (1),
        .TPRPDEN             (1),
        .TREFPDEN            (1),
        .TCPDED              (1),
        .TPD_MAX             (70200000),
        .TXPR                (270000),
        .TXPR_TCK            (5),
        .TXS                 (270000),
        .TXS_TCK             (5),
        .TXSDLL              (512),
        .TISXR               (350),
        .TCKSRE              (10000),
        .TCKSRE_TCK          (5),
        .TCKSRX              (10000),
        .TCKSRX_TCK          (5),
        .TCKESR_TCK          (4),
        .TAOF                (0.7),
        .TAONPD              (8500),
        .TAOFPD              (8500),
        .ODTH4               (4),
        .ODTH8               (6),
        .TADC                (0.7),
        .TWLMRD              (40),
        .TWLDQSEN            (25),
        .TWLOE               (2000),
        .DM_BITS             (2),
        .ADDR_BITS           (15),
        .ROW_BITS            (15),
        .COL_BITS            (10),
        .DQ_BITS             (16),
        .DQS_BITS            (2),
        .BA_BITS             (3),
        .MEM_BITS            (10),
        .AP                  (10),
        .BC                  (12),
        .BL_BITS             (3),
        .BO_BITS             (2),
        .CS_BITS             (1),
        .RANKS               (1),
        .RZQ                 (240),
        .PRE_DEF_PAT         (8'hAA),
        .STOP_ON_ERROR       (1),
        .DEBUG               (1),
        .BUS_DELAY           (0),
        .RANDOM_OUT_DELAY    (0),
        .RANDOM_SEED         (31913),
        .RDQSEN_PRE          (2),
        .RDQSEN_PST          (1),
        .RDQS_PRE            (2),
        .RDQS_PST            (1),
        .RDQEN_PRE           (0),
        .RDQEN_PST           (0),
        .WDQS_PRE            (2),
        .WDQS_PST            (1),
        .check_strict_mrbits (1),
        .check_strict_timing (1),
        .feature_pasr        (1),
        .feature_truebl4     (0),
        .feature_odt_hi      (0),
        .PERTCKAVG           (512),
        .LOAD_MODE           (4'b0000),
        .REFRESH             (4'b0001),
        .PRECHARGE           (4'b0010),
        .ACTIVATE            (4'b0011),
        .WRITE               (4'b0100),
        .READ                (4'b0101),
        .ZQ                  (4'b0110),
        .NOP                 (4'b0111),
        .PWR_DOWN            (4'b1000),
        .SELF_REF            (4'b1001),
        .RFF_BITS            (128),
        .RFF_CHUNK           (32),
        .SAME_BANK           (2'd0),
        .DIFF_BANK           (2'd1),
        .DIFF_GROUP          (2'd2),
        .SIMUL_500US         (5),
        .SIMUL_200US         (2)
    ) ddr3_i (
        .rst_n   (SDRST),         // input 
        .ck      (SDCLK),         // input 
        .ck_n    (SDNCLK),        // input 
        .cke     (SDCKE),         // input 
        .cs_n    (1'b0),          // input 
        .ras_n   (SDRAS),         // input 
        .cas_n   (SDCAS),         // input 
        .we_n    (SDWE),          // input 
        .dm_tdqs ({SDDMU,SDDML}), // inout[1:0] 
        .ba      (SDBA[2:0]),     // input[2:0] 
        .addr    (SDA[14:0]),     // input[14:0] 
        .dq      (SDD[15:0]),     // inout[15:0] 
        .dqs     ({DQSU,DQSL}),   // inout[1:0] 
        .dqs_n   ({NDQSU,NDQSL}), // inout[1:0] 
        .tdqs_n  (),              // output[1:0] 
        .odt     (SDODT)          // input 
    );
    
    
// Simulation modules    
simul_axi_master_rdaddr
#(
  .ID_WIDTH(12),
  .ADDRESS_WIDTH(32),
  .LATENCY(AXI_RDADDR_LATENCY),          // minimal delay between inout and output ( 0 - next cycle)
  .DEPTH(8),            // maximal number of commands in FIFO
  .DATA_DELAY(3.5),
  .VALID_DELAY(4.0)
) simul_axi_master_rdaddr_i (
    .clk(CLK),
    .reset(RST),
    .arid_in(ARID_IN[11:0]),
    .araddr_in(ARADDR_IN[31:0]),
    .arlen_in(ARLEN_IN[3:0]),
    .arsize_in(ARSIZE_IN[2:0]),
    .arburst_in(ARBURST_IN[1:0]),
    .arcache_in(4'b0),
    .arprot_in(3'b0), //     .arprot_in(2'b0),
    .arid(arid[11:0]),
    .araddr(araddr[31:0]),
    .arlen(arlen[3:0]),
    .arsize(arsize[2:0]),
    .arburst(arburst[1:0]),
    .arcache(arcache[3:0]),
    .arprot(arprot[2:0]),
    .arvalid(arvalid),
    .arready(arready),
    .set_cmd(AR_SET_CMD),  // latch all other input data at posedge of clock
    .ready(AR_READY)     // command/data FIFO can accept command
);

simul_axi_master_wraddr
#(
  .ID_WIDTH(12),
  .ADDRESS_WIDTH(32),
  .LATENCY(AXI_WRADDR_LATENCY),          // minimal delay between inout and output ( 0 - next cycle)
  .DEPTH(8),            // maximal number of commands in FIFO
  .DATA_DELAY(3.5),
  .VALID_DELAY(4.0)
) simul_axi_master_wraddr_i (
    .clk(CLK),
    .reset(RST),
    .awid_in(AWID_IN[11:0]),
    .awaddr_in(AWADDR_IN[31:0]),
    .awlen_in(AWLEN_IN[3:0]),
    .awsize_in(AWSIZE_IN[2:0]),
    .awburst_in(AWBURST_IN[1:0]),
    .awcache_in(4'b0),
    .awprot_in(3'b0), //.awprot_in(2'b0),
    .awid(awid[11:0]),
    .awaddr(awaddr[31:0]),
    .awlen(awlen[3:0]),
    .awsize(awsize[2:0]),
    .awburst(awburst[1:0]),
    .awcache(awcache[3:0]),
    .awprot(awprot[2:0]),
    .awvalid(awvalid),
    .awready(awready),
    .set_cmd(AW_SET_CMD),  // latch all other input data at posedge of clock
    .ready(AW_READY)     // command/data FIFO can accept command
);

simul_axi_master_wdata
#(
  .ID_WIDTH(12),
  .DATA_WIDTH(32),
  .WSTB_WIDTH(4),
  .LATENCY(AXI_WRDATA_LATENCY),          // minimal delay between inout and output ( 0 - next cycle)
  .DEPTH(8),            // maximal number of commands in FIFO
  .DATA_DELAY(3.2),
  .VALID_DELAY(3.6)
) simul_axi_master_wdata_i (
    .clk(CLK),
    .reset(RST),
    .wid_in(WID_IN[11:0]),
    .wdata_in(WDATA_IN[31:0]),
    .wstrb_in(WSTRB_IN[3:0]),
    .wlast_in(WLAST_IN),
    .wid(wid[11:0]),
    .wdata(wdata[31:0]),
    .wstrb(wstrb[3:0]),
    .wlast(wlast),
    .wvalid(wvalid),
    .wready(wready),
    .set_cmd(W_SET_CMD),  // latch all other input data at posedge of clock
    .ready(W_READY)        // command/data FIFO can accept command
);

simul_axi_slow_ready simul_axi_slow_ready_read_i(
    .clk(CLK),
    .reset(RST), //input         reset,
    .delay(RD_LAG), //input  [3:0]  delay,
    .valid(rvalid), // input         valid,
    .ready(rready)  //output        ready
    );

simul_axi_slow_ready simul_axi_slow_ready_write_resp_i(
    .clk(CLK),
    .reset(RST), //input         reset,
    .delay(B_LAG), //input  [3:0]  delay,
    .valid(bvalid), // input       ADDRESS_NUMBER+2:0  valid,
    .ready(bready)  //output        ready
    );

1000 1001 1002
simul_axi_read #(
    .ADDRESS_WIDTH(SIMUL_AXI_READ_WIDTH)
  ) simul_axi_read_i(
1003 1004 1005 1006
  .clk(CLK),
  .reset(RST),
  .last(rlast),
  .data_stb(rstb),
1007
  .raddr(ARADDR_IN[SIMUL_AXI_READ_WIDTH+1:2]), 
1008 1009
  .rlen(ARLEN_IN),
  .rcmd(AR_SET_CMD),
1010
  .addr_out(SIMUL_AXI_ADDR_W[SIMUL_AXI_READ_WIDTH-1:0]),
1011 1012 1013 1014 1015 1016 1017
  .burst(),     // burst in progress - just debug
  .err_out());  // data last does not match predicted or FIFO over/under run - just debug
    
    //  wire [ 3:0] SIMUL_ADD_ADDR; 
    always @ (posedge CLK) begin
        if      (RST) SIMUL_AXI_FULL <=0;
        else if (rstb) SIMUL_AXI_FULL <=1;
1018 1019 1020 1021 1022 1023
        
        if (RST) begin
              NUM_WORDS_READ <= 0;
        end else if (rstb) begin
            NUM_WORDS_READ <= NUM_WORDS_READ + 1; 
        end    
1024 1025 1026 1027 1028 1029 1030 1031 1032 1033 1034 1035 1036 1037
        if (rstb) begin
            SIMUL_AXI_ADDR <= SIMUL_AXI_ADDR_W;
            SIMUL_AXI_READ <= rdata;
`ifdef DEBUG_RD_DATA
        $display (" Read data (addr:data): 0x%x:0x%x @%t",SIMUL_AXI_ADDR_W,rdata,$time);
`endif  
            
        end 
        
    end
    
    
// SuppressWarnings VEditor all - these variables are just for viewing, not used anywhere else
  reg DEBUG1, DEBUG2, DEBUG3;
Andrey Filippov's avatar
Andrey Filippov committed
1038 1039
  reg [11:0] GLOBAL_WRITE_ID=0;
  reg [11:0] GLOBAL_READ_ID=0;
1040 1041 1042 1043 1044 1045 1046 1047 1048
  reg [7:0] target_phase=0; // to compare/wait for phase shifter ready
  
   task set_up;
        begin
// set dq /dqs tristate on/off patterns
            axi_set_tristate_patterns;
// set patterns for DM (always 0) and DQS - always the same (may try different for write lev.)
            axi_set_dqs_dqm_patterns;
// prepare all sequences
1049
            set_all_sequences;
1050
// prepare write buffer    
1051
            write_block_buf_chn(0,0,256); // fill block memory (channel, page, number)
1052 1053
// set all delays
//#axi_set_delays - from tables, per-pin
1054 1055
`ifdef SET_PER_PIN_DELAYS
            $display("SET_PER_PIN_DELAYS @ %t",$time);
1056 1057
            axi_set_delays; // set all individual delays, aslo runs axi_set_phase()
`else
1058
            $display("SET COMMON DELAYS @ %t",$time);
1059
            axi_set_same_delays(DLY_DQ_IDELAY,DLY_DQ_ODELAY,DLY_DQS_IDELAY,DLY_DQS_ODELAY,DLY_DM_ODELAY,DLY_CMDA_ODELAY);
1060 1061
// set clock phase relative to DDR clk
            axi_set_phase(DLY_PHASE);
1062 1063
`endif            
            
1064 1065 1066
        end
    endtask

1067 1068 1069 1070 1071
// tasks - when tested - move to includes

task test_write_levelling; // SuppressThisWarning VEditor - may be unused
  begin
// Set special values for DQS idelay for write leveling
1072
        wait_ps_pio_done(DEFAULT_STATUS_MODE,1); // not no interrupt running cycle - delays are changed immediately
1073 1074 1075 1076
        axi_set_dqs_idelay_wlv;
// Set write buffer (from DDR3) WE signal delay for write leveling mode
        axi_set_wbuf_delay(WBUF_DLY_WLV);
        axi_set_dqs_odelay('h80); // 'h80 - inverted, 'h60 - not - 'h80 will cause warnings during simulation
1077
        schedule_ps_pio ( // schedule software-control memory operation (may need to check FIFO status first)
1078 1079 1080 1081 1082 1083
                        WRITELEV_OFFSET,   // input [9:0] seq_addr; // sequence start address
                        0,                 // input [1:0] page;     // buffer page number
                        0,                 // input       urgent;   // high priority request (only for competion with other channels, wiil not pass in this FIFO)
                        0,                // input       chn;      // channel buffer to use: 0 - memory read, 1 - memory write
                        `PS_PIO_WAIT_COMPLETE );//  wait_complete; // Do not request a newe transaction from the scheduler until previous memory transaction is finished
                        
1084
        wait_ps_pio_done(DEFAULT_STATUS_MODE,1); // wait previous memory transaction finished before changing delays (effective immediately)
1085 1086 1087
        read_block_buf_chn (0, 0, 32, 1 ); // chn=0, page=0, number of 32-bit words=32, wait_done
//        @ (negedge rstb);
        axi_set_dqs_odelay(DLY_DQS_ODELAY);
1088
        schedule_ps_pio ( // schedule software-control memory operation (may need to check FIFO status first)
1089 1090 1091 1092 1093
                        WRITELEV_OFFSET,   // input [9:0] seq_addr; // sequence start address
                        1,                 // input [1:0] page;     // buffer page number
                        0,                 // input       urgent;   // high priority request (only for competion with other channels, wiil not pass in this FIFO)
                        0,                // input       chn;      // channel buffer to use: 0 - memory read, 1 - memory write
                        `PS_PIO_WAIT_COMPLETE );//  wait_complete; // Do not request a newe transaction from the scheduler until previous memory transaction is finished
1094
        wait_ps_pio_done(DEFAULT_STATUS_MODE,1); // wait previous memory transaction finished before changing delays (effective immediately)
1095 1096 1097 1098 1099
        read_block_buf_chn (0, 1, 32, 1 ); // chn=0, page=1, number of 32-bit words=32, wait_done
//    task wait_read_queue_empty; - alternative way to check fo empty read queue
        
//        @ (negedge rstb);
        axi_set_dqs_idelay_nominal;
1100 1101
        axi_set_dqs_odelay_nominal;
//        axi_set_dqs_odelay('h78);
1102 1103 1104 1105 1106 1107
        axi_set_wbuf_delay(WBUF_DLY_DFLT); //DFLT_WBUF_DELAY
   end
endtask

task test_read_pattern; // SuppressThisWarning VEditor - may be unused
    begin  
1108
        schedule_ps_pio ( // schedule software-control memory operation (may need to check FIFO status first)
1109 1110 1111 1112 1113
                        READ_PATTERN_OFFSET,   // input [9:0] seq_addr; // sequence start address
                        2,                     // input [1:0] page;     // buffer page number
                        0,                     // input       urgent;   // high priority request (only for competion with other channels, wiil not pass in this FIFO)
                        0,                    // input       chn;      // channel buffer to use: 0 - memory read, 1 - memory write
                        `PS_PIO_WAIT_COMPLETE );//  wait_complete; // Do not request a newe transaction from the scheduler until previous memory transaction is finished
1114
        wait_ps_pio_done(DEFAULT_STATUS_MODE,1); // wait previous memory transaction finished before changing delays (effective immediately)
1115 1116 1117 1118 1119 1120 1121
        read_block_buf_chn (0, 2, 32, 1 ); // chn=0, page=2, number of 32-bit words=32, wait_done
    end
endtask

task test_write_block; // SuppressThisWarning VEditor - may be unused
    begin
//    write_block_buf_chn; // fill block memory - already set in set_up task
1122
        schedule_ps_pio ( // schedule software-control memory operation (may need to check FIFO status first)
1123 1124 1125 1126 1127 1128
                        WRITE_BLOCK_OFFSET,    // input [9:0] seq_addr; // sequence start address
                        0,                     // input [1:0] page;     // buffer page number
                        0,                     // input       urgent;   // high priority request (only for competion with other channels, wiil not pass in this FIFO)
                        1,                    // input       chn;      // channel buffer to use: 0 - memory read, 1 - memory write
                        `PS_PIO_WAIT_COMPLETE );//  wait_complete; // Do not request a newe transaction from the scheduler until previous memory transaction is finished
// tempoary - for debugging:
1129
//        wait_ps_pio_done(DEFAULT_STATUS_MODE,1); // wait previous memory transaction finished before changing delays (effective immediately)
1130 1131 1132 1133 1134
    end
endtask

task test_read_block; // SuppressThisWarning VEditor - may be unused
    begin
1135
        schedule_ps_pio ( // schedule software-control memory operation (may need to check FIFO status first)
1136 1137 1138 1139 1140
                        READ_BLOCK_OFFSET,   // input [9:0] seq_addr; // sequence start address
                        3,                     // input [1:0] page;     // buffer page number
                        0,                     // input       urgent;   // high priority request (only for competion with other channels, wiil not pass in this FIFO)
                        0,                    // input       chn;      // channel buffer to use: 0 - memory read, 1 - memory write
                        `PS_PIO_WAIT_COMPLETE );//  wait_complete; // Do not request a newe transaction from the scheduler until previous memory transaction is finished
1141
        schedule_ps_pio ( // schedule software-control memory operation (may need to check FIFO status first)
1142 1143 1144 1145 1146
                        READ_BLOCK_OFFSET,   // input [9:0] seq_addr; // sequence start address
                        2,                     // input [1:0] page;     // buffer page number
                        0,                     // input       urgent;   // high priority request (only for competion with other channels, wiil not pass in this FIFO)
                        0,                    // input       chn;      // channel buffer to use: 0 - memory read, 1 - memory write
                        `PS_PIO_WAIT_COMPLETE );//  wait_complete; // Do not request a newe transaction from the scheduler until previous memory transaction is finished
1147
        schedule_ps_pio ( // schedule software-control memory operation (may need to check FIFO status first)
1148 1149 1150 1151 1152
                        READ_BLOCK_OFFSET,   // input [9:0] seq_addr; // sequence start address
                        1,                     // input [1:0] page;     // buffer page number
                        0,                     // input       urgent;   // high priority request (only for competion with other channels, wiil not pass in this FIFO)
                        0,                    // input       chn;      // channel buffer to use: 0 - memory read, 1 - memory write
                        `PS_PIO_WAIT_COMPLETE );//  wait_complete; // Do not request a newe transaction from the scheduler until previous memory transaction is finished
1153
        wait_ps_pio_done(DEFAULT_STATUS_MODE,1); // wait previous memory transaction finished before changing delays (effective immediately)
1154 1155 1156 1157 1158 1159 1160 1161
        read_block_buf_chn (0, 3, 256, 1 ); // chn=0, page=3, number of 32-bit words=256, wait_done
    end
endtask

task test_scanline_write; // SuppressThisWarning VEditor - may be unused
    input            [3:0] channel;
    input            [1:0] extra_pages;
    input                  wait_done;
1162 1163 1164 1165 1166
    input [15:0]           window_width;
    input [15:0]           window_height;
    input [15:0]           window_left;
    input [15:0]           window_top;
    
1167 1168 1169 1170 1171 1172 1173 1174
    
    reg             [29:0] start_addr;
    integer                mode;
    reg [STATUS_DEPTH-1:0] status_address;
    reg             [29:0] status_control_address;
    reg             [29:0] test_mode_address;
    
    integer       ii;
1175 1176 1177
    integer xfer_size;
    integer pages_per_row;
    integer startx,starty; // temporary - because of the vdt bug with integer ports
1178
    begin
1179
        pages_per_row= (window_width>>NUM_XFER_BITS)+((window_width[NUM_XFER_BITS-1:0]==0)?0:1);
1180 1181 1182 1183 1184 1185 1186 1187 1188 1189 1190 1191 1192 1193 1194 1195 1196 1197 1198 1199 1200 1201 1202 1203 1204 1205 1206 1207 1208 1209 1210
        $display("====== test_scanline_write: channel=%d, extra_pages=%d,  wait_done=%d @%t",
                                              channel,    extra_pages,     wait_done,   $time);
        case (channel)
            1:  begin
                    start_addr=             MCNTRL_SCANLINE_CHN1_ADDR;
                    status_address=         MCNTRL_TEST01_STATUS_REG_CHN1_ADDR;
                    status_control_address= MCNTRL_TEST01_ADDR + MCNTRL_TEST01_CHN1_STATUS_CNTRL;
                    test_mode_address=      MCNTRL_TEST01_ADDR + MCNTRL_TEST01_CHN1_MODE;
                end
            3:  begin
                    start_addr=             MCNTRL_SCANLINE_CHN3_ADDR;
                    status_address=         MCNTRL_TEST01_STATUS_REG_CHN3_ADDR;
                    status_control_address= MCNTRL_TEST01_ADDR + MCNTRL_TEST01_CHN3_STATUS_CNTRL;
                    test_mode_address=      MCNTRL_TEST01_ADDR + MCNTRL_TEST01_CHN3_MODE;
                end
            default: begin
                $display("**** ERROR: Invalid channel, only 1 and 3 are valid");
                start_addr=             MCNTRL_SCANLINE_CHN1_ADDR;
                status_address=         MCNTRL_TEST01_STATUS_REG_CHN1_ADDR;
                status_control_address= MCNTRL_TEST01_ADDR + MCNTRL_TEST01_CHN1_STATUS_CNTRL;
                test_mode_address=      MCNTRL_TEST01_ADDR + MCNTRL_TEST01_CHN1_MODE;
            end
        endcase
        mode=   func_encode_mode_scanline(
                    extra_pages,
                    1, // write_mem,
                    1, // enable
                    0);  // chn_reset
                
        write_contol_register(start_addr+ MCNTRL_SCANLINE_STARTADDR,        FRAME_START_ADDRESS); // RA=80, CA=0, BA=0 22-bit frame start address (3 CA LSBs==0. BA==0) 
        write_contol_register(start_addr + MCNTRL_SCANLINE_FRAME_FULL_WIDTH, FRAME_FULL_WIDTH);
1211 1212
        write_contol_register(start_addr + MCNTRL_SCANLINE_WINDOW_WH,        {window_height,window_width}); //WINDOW_WIDTH + (WINDOW_HEIGHT<<16));
        write_contol_register(start_addr + MCNTRL_SCANLINE_WINDOW_X0Y0,      {window_top,window_left}); //WINDOW_X0+ (WINDOW_Y0<<16));
1213 1214 1215 1216 1217 1218 1219 1220
        write_contol_register(start_addr + MCNTRL_SCANLINE_WINDOW_STARTXY,   SCANLINE_STARTX+(SCANLINE_STARTY<<16));
        write_contol_register(start_addr + MCNTRL_SCANLINE_MODE,             mode); 
        configure_channel_priority(channel,0);    // lowest priority channel 3
//        enable_memcntrl_channels(16'h000b); // channels 0,1,3 are enabled
        enable_memcntrl_en_dis(channel,1);
        write_contol_register(test_mode_address,            TEST01_START_FRAME);
        for (ii=0;ii<TEST_INITIAL_BURST;ii=ii+1) begin
// VDT bugs: 1:does not propagate undefined width through ?:, 2: - does not allow to connect it to task integer input, 3: shows integer input width as 1  
1221
            xfer_size= ((pages_per_row>1)?
1222 1223
                (
                    (
1224
                        ((ii % pages_per_row) < (pages_per_row-1))?
1225
                        (1<<NUM_XFER_BITS):
1226
                        (window_width % (1<<NUM_XFER_BITS))
1227 1228
                    )
                ):
1229
                ({16'b0,window_width}));
1230
           $display("########### test_scanline_write block %d: channel=%d, @%t", ii, channel, $time);
1231 1232
           startx=window_left + ((ii % pages_per_row)<<NUM_XFER_BITS);
           starty=window_top + (ii / pages_per_row);
1233 1234 1235
           write_block_scanline_chn(
            channel,
            (ii & 3),
1236 1237 1238
            xfer_size,
            startx, //window_left + ((ii % pages_per_row)<<NUM_XFER_BITS),  // SCANLINE_CUR_X,
            starty); // window_top + (ii / pages_per_row)); // SCANLINE_CUR_Y);\
1239 1240
            
        end
1241
        for (ii=0;ii< (window_height * pages_per_row) ;ii = ii+1) begin // here assuming 1 page per line
1242 1243 1244 1245 1246 1247 1248
            if (ii >= TEST_INITIAL_BURST) begin // wait page ready and fill page after first 4 are filled
                wait_status_condition (
                    status_address, //MCNTRL_TEST01_STATUS_REG_CHN3_ADDR,
                    status_control_address, // MCNTRL_TEST01_ADDR + MCNTRL_TEST01_CHN3_STATUS_CNTRL,
                    DEFAULT_STATUS_MODE,
                    (ii-TEST_INITIAL_BURST)<<16, // 4-bit page number
                    'hf << 16,  // mask for the 4-bit page number
1249 1250
                    1, // not equal to
                    (ii == TEST_INITIAL_BURST)); // synchronize sequence number - only first time, next just wait fro auto update
1251
                xfer_size= ((pages_per_row>1)?
1252 1253
                    (
                        (
1254
                            ((ii % pages_per_row) < (pages_per_row-1))?
1255 1256
                        
                         (1<<NUM_XFER_BITS):
1257
                            (window_width % (1<<NUM_XFER_BITS))
1258 1259
                        )
                    ):
1260
                    ({16'b0,window_width}));
1261
                $display("########### test_scanline_write block %d: channel=%d, @%t", ii, channel, $time);
1262 1263 1264
                startx=window_left + ((ii % pages_per_row)<<NUM_XFER_BITS);
                starty=window_top + (ii / pages_per_row);
                
1265 1266 1267
                write_block_scanline_chn(
                    channel,
                    (ii & 3),
1268 1269 1270
                xfer_size,
                startx,  // window_left + ((ii % pages_per_row)<<NUM_XFER_BITS),  // SCANLINE_CUR_X,
                starty); // window_top + (ii / pages_per_row)); // SCANLINE_CUR_Y);
1271 1272 1273 1274 1275 1276 1277 1278 1279 1280
            end
            write_contol_register(test_mode_address,            TEST01_NEXT_PAGE);
        end
        if (wait_done) begin
            wait_status_condition ( // may also be read directly from the same bit of mctrl_linear_rw (address=5) status
                status_address, // MCNTRL_TEST01_STATUS_REG_CHN3_ADDR,
                status_control_address, // MCNTRL_TEST01_ADDR + MCNTRL_TEST01_CHN3_STATUS_CNTRL,
                DEFAULT_STATUS_MODE,
                2 << STATUS_2LSB_SHFT, // bit 24 - busy, bit 25 - frame done
                2 << STATUS_2LSB_SHFT,  // mask for the 4-bit page number
1281 1282
                0, // equal to
                0); // no need to synchronize sequence number
1283 1284 1285 1286 1287 1288 1289 1290 1291
//     enable_memcntrl_en_dis(channel,0); // disable channel
        end
    end
endtask

task test_scanline_read; // SuppressThisWarning VEditor - may be unused
    input            [3:0] channel;
    input            [1:0] extra_pages;
    input                  show_data;
1292 1293 1294 1295
    input [15:0]           window_width;
    input [15:0]           window_height;
    input [15:0]           window_left;
    input [15:0]           window_top;
1296 1297 1298 1299 1300 1301 1302
    
    reg             [29:0] start_addr;
    integer                mode;
    reg [STATUS_DEPTH-1:0] status_address;
    reg             [29:0] status_control_address;
    reg             [29:0] test_mode_address;
    integer       ii;
1303 1304 1305
    integer xfer_size;
    integer pages_per_row;
    
1306
    begin
1307
        pages_per_row= (window_width>>NUM_XFER_BITS)+((window_width[NUM_XFER_BITS-1:0]==0)?0:1);
1308 1309 1310 1311 1312 1313 1314 1315 1316 1317 1318 1319 1320 1321 1322 1323 1324 1325 1326 1327 1328 1329 1330 1331 1332 1333 1334 1335 1336 1337 1338 1339
        $display("====== test_scanline_read: channel=%d, extra_pages=%d,  show_data=%d @%t",
                                             channel,    extra_pages,     show_data,    $time);
        case (channel)
            1:  begin
                    start_addr=             MCNTRL_SCANLINE_CHN1_ADDR;
                    status_address=         MCNTRL_TEST01_STATUS_REG_CHN1_ADDR;
                    status_control_address= MCNTRL_TEST01_ADDR + MCNTRL_TEST01_CHN1_STATUS_CNTRL;
                    test_mode_address=      MCNTRL_TEST01_ADDR + MCNTRL_TEST01_CHN1_MODE;
                end
            3:  begin
                    start_addr=             MCNTRL_SCANLINE_CHN3_ADDR;
                    status_address=         MCNTRL_TEST01_STATUS_REG_CHN3_ADDR;
                    status_control_address= MCNTRL_TEST01_ADDR + MCNTRL_TEST01_CHN3_STATUS_CNTRL;
                    test_mode_address=      MCNTRL_TEST01_ADDR + MCNTRL_TEST01_CHN3_MODE;
                end
            default: begin
                $display("**** ERROR: Invalid channel, only 1 and 3 are valid");
                start_addr=             MCNTRL_SCANLINE_CHN1_ADDR;
                status_address=         MCNTRL_TEST01_STATUS_REG_CHN1_ADDR;
                status_control_address= MCNTRL_TEST01_ADDR + MCNTRL_TEST01_CHN1_STATUS_CNTRL;
                test_mode_address=      MCNTRL_TEST01_ADDR + MCNTRL_TEST01_CHN1_MODE;
            end
        endcase
        mode=   func_encode_mode_scanline(
                    extra_pages,
                    0, // write_mem,
                    1, // enable
                    0);  // chn_reset

   // program to the
        write_contol_register(start_addr + MCNTRL_SCANLINE_STARTADDR,        FRAME_START_ADDRESS); // RA=80, CA=0, BA=0 22-bit frame start address (3 CA LSBs==0. BA==0) 
        write_contol_register(start_addr + MCNTRL_SCANLINE_FRAME_FULL_WIDTH, FRAME_FULL_WIDTH);
1340 1341
        write_contol_register(start_addr + MCNTRL_SCANLINE_WINDOW_WH,        {window_height,window_width}); //WINDOW_WIDTH + (WINDOW_HEIGHT<<16));
        write_contol_register(start_addr + MCNTRL_SCANLINE_WINDOW_X0Y0,      {window_top,window_left}); //WINDOW_X0+ (WINDOW_Y0<<16));
1342 1343 1344 1345 1346
        write_contol_register(start_addr + MCNTRL_SCANLINE_WINDOW_STARTXY,   SCANLINE_STARTX+(SCANLINE_STARTY<<16));
        write_contol_register(start_addr + MCNTRL_SCANLINE_MODE,             mode);// set mode register: {extra_pages[1:0],enable,!reset}
        configure_channel_priority(channel,0);    // lowest priority channel 3
        enable_memcntrl_en_dis(channel,1);
        write_contol_register(test_mode_address,            TEST01_START_FRAME);
1347 1348
        for (ii=0;ii<(window_height * pages_per_row);ii = ii+1) begin
            xfer_size= ((pages_per_row>1)?
1349 1350
                (
                    (
1351
                        ((ii % pages_per_row) < (pages_per_row-1))?
1352
                        (1<<NUM_XFER_BITS):
1353
                        (window_width % (1<<NUM_XFER_BITS))
1354 1355
                    )
                ):
1356
                ({16'b0,window_width}));
1357 1358 1359 1360 1361 1362
            wait_status_condition (
                status_address, //MCNTRL_TEST01_STATUS_REG_CHN2_ADDR,
                status_control_address, // MCNTRL_TEST01_ADDR + MCNTRL_TEST01_CHN2_STATUS_CNTRL,
                DEFAULT_STATUS_MODE,
                (ii) << 16, // -TEST_INITIAL_BURST)<<16, // 4-bit page number
                'hf << 16,  // mask for the 4-bit page number
1363 1364
                 1, // not equal to
                 (ii == 0)); // synchronize sequence number - only first time, next just wait fro auto update
1365
// read block (if needed), for now just sikip  
1366 1367 1368 1369 1370
                if (show_data) begin
                    $display("########### test_scanline_read block %d: channel=%d, @%t", ii, channel, $time);
                    read_block_buf_chn (
                        channel,
                        (ii & 3),
1371
                        xfer_size <<2,
1372
                        1 ); // chn=0, page=3, number of 32-bit words=256, wait_done
1373 1374 1375 1376 1377 1378 1379 1380 1381 1382 1383 1384
                end
        write_contol_register(test_mode_address,            TEST01_NEXT_PAGE);
    end
  end  
endtask

task test_tiled_write; // SuppressThisWarning VEditor - may be unused
    input            [3:0] channel;
    input                  byte32;
    input                  keep_open;
    input            [1:0] extra_pages;
    input                  wait_done;
1385 1386 1387 1388 1389 1390 1391 1392 1393
    input [15:0]           window_width;
    input [15:0]           window_height;
    input [15:0]           window_left;
    input [15:0]           window_top;
    input [ 7:0]           tile_width;
    input [ 7:0]           tile_height;
    input [ 7:0]           tile_vstep;
    
    
1394 1395 1396 1397 1398 1399 1400
    
    reg             [29:0] start_addr;
    integer                mode;
    reg [STATUS_DEPTH-1:0] status_address;
    reg             [29:0] status_control_address;
    reg             [29:0] test_mode_address;
    integer       ii;
1401 1402 1403 1404
    integer       tiles_per_row;
    integer       tile_rows_per_window;
    integer       tile_size;
    integer startx,starty; // temporary - because of the vdt bug with integer ports
1405
    begin
1406 1407 1408
        tiles_per_row= (window_width/tile_width)+  ((window_width % tile_width==0)?0:1);
        tile_rows_per_window= ((window_height-1)/tile_vstep) + 1;
        tile_size= tile_width*tile_height;
1409 1410 1411 1412 1413 1414 1415 1416 1417 1418 1419 1420 1421 1422 1423 1424 1425 1426 1427 1428 1429 1430 1431 1432 1433 1434 1435 1436 1437 1438 1439 1440
        $display("====== test_tiled_write: channel=%d, byte32=%d, keep_open=%d, extra_pages=%d,  wait_done=%d @%t",
                                           channel,    byte32,    keep_open,    extra_pages,     wait_done,   $time);
        case (channel)
            2:  begin
                    start_addr=             MCNTRL_TILED_CHN2_ADDR;
                    status_address=         MCNTRL_TEST01_STATUS_REG_CHN2_ADDR;
                    status_control_address= MCNTRL_TEST01_ADDR + MCNTRL_TEST01_CHN2_STATUS_CNTRL;
                    test_mode_address=      MCNTRL_TEST01_ADDR + MCNTRL_TEST01_CHN2_MODE;
                end
            4:  begin
                    start_addr=             MCNTRL_TILED_CHN4_ADDR;
                    status_address=         MCNTRL_TEST01_STATUS_REG_CHN4_ADDR;
                    status_control_address= MCNTRL_TEST01_ADDR + MCNTRL_TEST01_CHN4_STATUS_CNTRL;
                    test_mode_address=      MCNTRL_TEST01_ADDR + MCNTRL_TEST01_CHN4_MODE;
                end
            default: begin
                $display("**** ERROR: Invalid channel, only 2 and 4 are valid");
                start_addr=             MCNTRL_TILED_CHN2_ADDR;
                status_address=         MCNTRL_TEST01_STATUS_REG_CHN2_ADDR;
                status_control_address= MCNTRL_TEST01_ADDR + MCNTRL_TEST01_CHN2_STATUS_CNTRL;
                test_mode_address=      MCNTRL_TEST01_ADDR + MCNTRL_TEST01_CHN2_MODE;
            end
        endcase
        mode=   func_encode_mode_tiled(
                    byte32,
                    keep_open,
                    extra_pages,
                    1, // write_mem,
                    1, // enable
                    0);  // chn_reset
        write_contol_register(start_addr + MCNTRL_TILED_STARTADDR,        FRAME_START_ADDRESS); // RA=80, CA=0, BA=0 22-bit frame start address (3 CA LSBs==0. BA==0) 
        write_contol_register(start_addr + MCNTRL_TILED_FRAME_FULL_WIDTH, FRAME_FULL_WIDTH);
1441 1442 1443
        write_contol_register(start_addr + MCNTRL_TILED_WINDOW_WH,        {window_height,window_width}); //WINDOW_WIDTH + (WINDOW_HEIGHT<<16));
        write_contol_register(start_addr + MCNTRL_TILED_WINDOW_X0Y0,      {window_top,window_left}); //WINDOW_X0+ (WINDOW_Y0<<16));
        
1444
        write_contol_register(start_addr + MCNTRL_TILED_WINDOW_STARTXY,   TILED_STARTX+(TILED_STARTY<<16));
1445
        write_contol_register(start_addr + MCNTRL_TILED_TILE_WHS,         {8'b0,tile_vstep,tile_height,tile_width});//tile_width+(tile_height<<8)+(tile_vstep<<16));
1446 1447 1448 1449 1450 1451
        write_contol_register(start_addr + MCNTRL_TILED_MODE,             mode);// set mode register: {extra_pages[1:0],enable,!reset}
        configure_channel_priority(channel,0);    // lowest priority channel 3
        enable_memcntrl_en_dis(channel,1);
        write_contol_register(test_mode_address,            TEST01_START_FRAME);
    
        for (ii=0;ii<TEST_INITIAL_BURST;ii=ii+1) begin
1452
            $display("########### test_tiled_write block %d: channel=%d, @%t", ii, channel, $time);
1453 1454
            startx = window_left + ((ii % tiles_per_row) * tile_width);
            starty = window_top + (ii / tile_rows_per_window); // SCANLINE_CUR_Y);\
1455 1456 1457
            write_block_scanline_chn( // TODO: Make a different tile buffer data, matching the order
                channel, // channel
                (ii & 3),
1458 1459 1460
                tile_size,
                startx, //window_left + ((ii % tiles_per_row) * tile_width),
                starty); //window_top + (ii / tile_rows_per_window)); // SCANLINE_CUR_Y);\
1461 1462
        end
    
1463
        for (ii=0;ii<(tiles_per_row * tile_rows_per_window);ii = ii+1) begin
1464 1465 1466 1467 1468 1469 1470
            if (ii >= TEST_INITIAL_BURST) begin // wait page ready and fill page after first 4 are filled
                wait_status_condition (
                    status_address, // MCNTRL_TEST01_STATUS_REG_CHN5_ADDR,
                    status_control_address, // MCNTRL_TEST01_ADDR + MCNTRL_TEST01_CHN5_STATUS_CNTRL,
                    DEFAULT_STATUS_MODE,
                    (ii-TEST_INITIAL_BURST)<<16, // 4-bit page number
                    'hf << 16,  // mask for the 4-bit page number
1471 1472
                    1, // not equal to
                    (ii == TEST_INITIAL_BURST)); // synchronize sequence number - only first time, next just wait fro auto update
1473
                $display("########### test_tiled_write block %d: channel=%d, @%t", ii, channel, $time);
1474 1475
                startx = window_left + ((ii % tiles_per_row) * tile_width);
                starty = window_top + (ii / tile_rows_per_window);
1476 1477 1478
                write_block_scanline_chn( // TODO: Make a different tile buffer data, matching the order
                    channel, // channel
                    (ii & 3),
1479 1480 1481
                    tile_size,
                    startx, // window_left + ((ii % tiles_per_row) * tile_width),
                    starty); // window_top + (ii / tile_rows_per_window)); // SCANLINE_CUR_Y);\
1482 1483 1484 1485 1486 1487 1488 1489 1490 1491
            end
            write_contol_register(test_mode_address,            TEST01_NEXT_PAGE);
        end
        if (wait_done) begin
            wait_status_condition ( // may also be read directly from the same bit of mctrl_linear_rw (address=5) status
                status_address, // MCNTRL_TEST01_STATUS_REG_CHN3_ADDR,
                status_control_address, // MCNTRL_TEST01_ADDR + MCNTRL_TEST01_CHN3_STATUS_CNTRL,
                DEFAULT_STATUS_MODE,
                2 << STATUS_2LSB_SHFT, // bit 24 - busy, bit 25 - frame done
                2 << STATUS_2LSB_SHFT,  // mask for the 4-bit page number
1492 1493
                0, // equal to
                0); // no need to synchronize sequence number
1494 1495 1496 1497 1498 1499 1500 1501 1502 1503 1504 1505 1506
//     enable_memcntrl_en_dis(channel,0); // disable channel
        end
    end  
endtask



task test_tiled_read; // SuppressThisWarning VEditor - may be unused
    input            [3:0] channel;
    input                  byte32;
    input                  keep_open;
    input            [1:0] extra_pages;
    input                  show_data;
1507 1508 1509 1510 1511 1512 1513
    input [15:0]           window_width;
    input [15:0]           window_height;
    input [15:0]           window_left;
    input [15:0]           window_top;
    input [ 7:0]           tile_width;
    input [ 7:0]           tile_height;
    input [ 7:0]           tile_vstep;
1514 1515 1516 1517 1518 1519 1520 1521
    
    reg             [29:0] start_addr;
    integer                mode;
    reg [STATUS_DEPTH-1:0] status_address;
    reg             [29:0] status_control_address;
    reg             [29:0] test_mode_address;
    
    integer       ii;
1522 1523 1524 1525
    integer       tiles_per_row;
    integer       tile_rows_per_window;
    integer       tile_size;
    
1526
    begin
1527 1528 1529
        tiles_per_row= (window_width/tile_width)+  ((window_width % tile_width==0)?0:1);
        tile_rows_per_window= ((window_height-1)/tile_vstep) + 1;
        tile_size= tile_width*tile_height;
1530 1531 1532 1533 1534 1535 1536 1537 1538 1539 1540 1541 1542 1543 1544 1545 1546 1547 1548 1549 1550 1551 1552 1553 1554 1555 1556 1557 1558 1559 1560 1561
        $display("====== test_tiled_read: channel=%d, byte32=%d, keep_open=%d, extra_pages=%d,  show_data=%d @%t",
                                          channel,      byte32,  keep_open,    extra_pages,     show_data,   $time);
        case (channel)
            2:  begin
                    start_addr=             MCNTRL_TILED_CHN2_ADDR;
                    status_address=         MCNTRL_TEST01_STATUS_REG_CHN2_ADDR;
                    status_control_address= MCNTRL_TEST01_ADDR + MCNTRL_TEST01_CHN2_STATUS_CNTRL;
                    test_mode_address=      MCNTRL_TEST01_ADDR + MCNTRL_TEST01_CHN2_MODE;
                end
            4:  begin
                    start_addr=             MCNTRL_TILED_CHN4_ADDR;
                    status_address=         MCNTRL_TEST01_STATUS_REG_CHN4_ADDR;
                    status_control_address= MCNTRL_TEST01_ADDR + MCNTRL_TEST01_CHN4_STATUS_CNTRL;
                    test_mode_address=      MCNTRL_TEST01_ADDR + MCNTRL_TEST01_CHN4_MODE;
                end
            default: begin
                $display("**** ERROR: Invalid channel, only 2 and 4 are valid");
                start_addr=             MCNTRL_TILED_CHN2_ADDR;
                status_address=         MCNTRL_TEST01_STATUS_REG_CHN2_ADDR;
                status_control_address= MCNTRL_TEST01_ADDR + MCNTRL_TEST01_CHN2_STATUS_CNTRL;
                test_mode_address=      MCNTRL_TEST01_ADDR + MCNTRL_TEST01_CHN2_MODE;
            end
        endcase
        mode=   func_encode_mode_tiled(
                    byte32,
                    keep_open,
                    extra_pages,
                    0, // write_mem,
                    1, // enable
                    0);  // chn_reset
        write_contol_register(start_addr + MCNTRL_TILED_STARTADDR,        FRAME_START_ADDRESS); // RA=80, CA=0, BA=0 22-bit frame start address (3 CA LSBs==0. BA==0) 
        write_contol_register(start_addr + MCNTRL_TILED_FRAME_FULL_WIDTH, FRAME_FULL_WIDTH);
1562 1563 1564
        write_contol_register(start_addr + MCNTRL_TILED_WINDOW_WH,        {window_height,window_width}); //WINDOW_WIDTH + (WINDOW_HEIGHT<<16));
        write_contol_register(start_addr + MCNTRL_TILED_WINDOW_X0Y0,      {window_top,window_left}); //WINDOW_X0+ (WINDOW_Y0<<16));
        
1565
        write_contol_register(start_addr + MCNTRL_TILED_WINDOW_STARTXY,   TILED_STARTX+(TILED_STARTY<<16));
1566
        write_contol_register(start_addr + MCNTRL_TILED_TILE_WHS,         {8'b0,tile_vstep,tile_height,tile_width});//(tile_height<<8)+(tile_vstep<<16));
1567 1568 1569 1570
        write_contol_register(start_addr + MCNTRL_TILED_MODE,             mode);// set mode register: {extra_pages[1:0],enable,!reset}
        configure_channel_priority(channel,0);    // lowest priority channel 3
        enable_memcntrl_en_dis(channel,1);
        write_contol_register(test_mode_address,            TEST01_START_FRAME);
1571
        for (ii=0;ii<(tiles_per_row * tile_rows_per_window);ii = ii+1) begin
1572 1573 1574 1575 1576 1577
            wait_status_condition (
                status_address, // MCNTRL_TEST01_STATUS_REG_CHN4_ADDR,
                status_control_address, // MCNTRL_TEST01_ADDR + MCNTRL_TEST01_CHN4_STATUS_CNTRL,
                DEFAULT_STATUS_MODE,
                ii << 16, // -TEST_INITIAL_BURST)<<16, // 4-bit page number
                'hf << 16,  // mask for the 4-bit page number
1578 1579
                1, // not equal to
                (ii == 0)); // synchronize sequence number - only first time, next just wait fro auto update
1580
                if (show_data) begin 
1581 1582 1583 1584
                    $display("########### test_tiled_read block %d: channel=%d, @%t", ii, channel, $time);
                    read_block_buf_chn (
                        channel,
                        (ii & 3),
1585
                        tile_size <<2,
1586
                        1 ); // chn=0, page=3, number of 32-bit words=256, wait_done
1587 1588 1589 1590 1591 1592 1593 1594 1595 1596 1597 1598 1599
                end
            write_contol_register(test_mode_address,            TEST01_NEXT_PAGE);
        end
//     enable_memcntrl_en_dis(channel,0); // disable channel
    end  
endtask







1600 1601 1602 1603 1604 1605
task set_all_sequences;
        begin
            $display("SET MRS @ %t",$time);    
            set_mrs(1);
            $display("SET REFRESH @ %t",$time);    
            set_refresh(
1606 1607
                T_RFC, // input [ 9:0] t_rfc; // =50 for tCK=2.5ns
                T_REFI); //input [ 7:0] t_refi; // 48/97 for normal, 8 - for simulation
1608 1609 1610 1611 1612 1613 1614 1615 1616 1617 1618 1619 1620 1621 1622 1623 1624 1625 1626
            $display("SET WRITE LEVELING @ %t",$time);    
            set_write_lev(16); // write leveling, 16 times   (full buffer - 128) 
            $display("SET READ PATTERN @ %t",$time);    
            set_read_pattern(8); // 8x2*64 bits, 32x32 bits to read
            $display("SET WRITE BLOCK @ %t",$time);    
            set_write_block(
                3'h5,     // bank
                15'h1234, // row address
                10'h100   // column address
            );
           
            $display("SET READ BLOCK @ %t",$time);    
            set_read_block(
                3'h5,     // bank
                15'h1234, // row address
                10'h100   // column address
            );
        end
endtask
Andrey Filippov's avatar
Andrey Filippov committed
1627

1628
task write_block_scanline_chn;  // S uppressThisWarning VEditor : may be unused
1629 1630
//    input integer chn; // buffer channel
    input   [3:0] chn; // buffer channel
1631 1632 1633 1634 1635 1636 1637 1638 1639 1640 1641
    input   [1:0] page;
//    input integer num_words; // number of words to write (will be rounded up to multiple of 16)
    input [NUM_XFER_BITS:0] num_bursts; // number of 8-bursts to write (will be rounded up to multiple of 16)
    input integer startX;
    input integer startY;
    reg    [29:0] start_addr;
    integer num_words;
    begin
//        $display("====== write_block_scanline_chn:%d page: %x X=0x%x Y=0x%x num=%d @%t", chn, page, startX, startY,num_words, $time);
        $display("====== write_block_scanline_chn:%d page: %x X=0x%x Y=0x%x num=%d @%t", chn, page, startX, startY,num_bursts, $time);
        case (chn)
1642
            0:  start_addr=MCONTR_BUF0_WR_ADDR + (page << 8);
1643
            1:  start_addr=MCONTR_BUF1_WR_ADDR + (page << 8);
1644
            2:  start_addr=MCONTR_BUF2_WR_ADDR + (page << 8);
1645
            3:  start_addr=MCONTR_BUF3_WR_ADDR + (page << 8);
1646
            4:  start_addr=MCONTR_BUF4_WR_ADDR + (page << 8);
1647 1648
            default: begin
                $display("**** ERROR: Invalid channel for write_block_scanline_chn = %d @%t", chn, $time);
1649
                start_addr = MCONTR_BUF0_WR_ADDR+ (page << 8);
1650 1651 1652 1653 1654 1655 1656 1657
            end
        endcase
        num_words=num_bursts << 2;
        write_block_incremtal (start_addr, num_words, (startX<<2) + (startY<<16)); // 1 of startX is 8x16 bit, 16 bytes or 4 32-bit words
//        write_block_incremtal (start_addr, num_bursts << 2, (startX<<2) + (startY<<16)); // 1 of startX is 8x16 bit, 16 bytes or 4 32-bit words
    end
endtask

1658 1659 1660 1661 1662 1663 1664 1665 1666 1667 1668 1669 1670 1671 1672 1673 1674 1675 1676 1677 1678 1679 1680 1681 1682 1683 1684 1685 1686 1687 1688 1689 1690 1691 1692 1693
function [6:0] func_encode_mode_tiled;
    input       byte32; // 32-byte columns (0 - 16-byte columns)
    input       keep_open; // for 8 or less rows - do not close page between accesses
    input [1:0] extra_pages; // number of extra pages that need to stay (not to be overwritten) in the buffer
                             // can be used for overlapping tile read access
    input       write_mem;   // write to memory mode (0 - read from memory)
    input       enable;      // enable requests from this channel ( 0 will let current to finish, but not raise want/need)
    input       chn_reset;       // immediately reset al;l the internal circuitry
    begin
        func_encode_mode_tiled={byte32,keep_open,extra_pages,write_mem,enable,~chn_reset};
    end           
endfunction
function [4:0] func_encode_mode_scanline;
    input [1:0] extra_pages; // number of extra pages that need to stay (not to be overwritten) in the buffer
                             // can be used for overlapping tile read access
    input       write_mem;   // write to memory mode (0 - read from memory)
    input       enable;      // enable requests from this channel ( 0 will let current to finish, but not raise want/need)
    input       chn_reset;       // immediately reset al;l the internal circuitry
    begin
        func_encode_mode_scanline={extra_pages,write_mem,enable,~chn_reset};
    end           
endfunction
/*
task enable_memcntrl_en_dis;
    input [3:0] chn;
    input       en;
    begin
        if (en) begin
            ENABLED_CHANNELS = ENABLED_CHANNELS | (1<<chn);
        end else begin
            ENABLED_CHANNELS = ENABLED_CHANNELS & ~(1<<chn);
        end
        write_contol_register(MCONTR_TOP_16BIT_ADDR +  MCONTR_TOP_16BIT_CHN_EN, {16'b0,ENABLED_CHANNELS});
    end
endtask
*/
Andrey Filippov's avatar
Andrey Filippov committed
1694

1695 1696 1697
`include "includes/x393_tasks_mcntrl_en_dis_priority.vh"
`include "includes/x393_tasks_mcntrl_buffers.vh"
`include "includes/x393_tasks_pio_sequences.vh"
1698
`include "includes/x393_tasks_mcntrl_timing.vh" // SuppressThisWarning VEditor - not used
1699 1700
`include "includes/x393_tasks_ps_pio.vh"
`include "includes/x393_tasks_status.vh"
1701
`include "includes/x393_tasks01.vh"
1702
`include "includes/x393_mcontr_encode_cmd.vh"
1703 1704
endmodule