merged with framepars (5edb25c9) · Commits · Elphel / linux-elphel

src/arch/arm/boot/dts/elphel393.dts

deleted100644 → 0

+0 −294

Original line number	Diff line number	Diff line
		/* welcome to elphel393 device tree */
		/include/ "elphel393-zynq-base.dtsi"
		/include/ "elphel393-bootargs.dtsi"

		/ {
		model = "Elphel 10393";

		ps7_axi_interconnect_0: amba@0 {

		ps7_i2c_0: ps7-i2c@e0004000 {
		bus-id = <0>;
		i2c-clk = <400000>;
		rtc@68 {
		compatible = "stm,m41t62";
		reg = <0x68>;
		};

		vsc330x@1 {
		compatible = "vsc,vsc3304";
		reg = <0x01>;
		vsc330x,configuration_name = "elphel393: from external";
		/* configuration below is for external eSATA host accessing SSD. Will chnage
		* when the SATA controller code will be operational
		* TODO: specify optimal drive strength, pre-emphasis, etc.
		* All parameters are exported to sysfs for run-time modification
		*/
		vsc330x,configuration_data=<
		0x11080101 /page 0x11, register 0x08, data=0x1 (inverted input), write enabled mask=0x1 /
		0x11090001
		0x110a0101
		0x110b0101
		0x110e0001
		0x110f0101

		0x230a0b1f /* set output mode for port 10 as non-inverted, forwarding OOB enabled */
		0x230b151f /* set output mode for port 11 as inverted, forwarding OOB enabled */
		0x230c151f
		0x230d0b1f
		0x230e151f
		0x230f151f

		0xff750101 /* freeze configuration to enable simultaneous modification */
		0x110e0002 /* enable channel 14 input */
		0x11090002 /* enable channel 9 input */

		0x000b091f /* connect port 11 output to input 9 */
		0x000c0e1f /* connect port 12 output to input 14 */
		0xff750001 /* un-freeze configuration to apply connection modifications */
		>;
		};

		si5338@70 {
		compatible = "sil,si5338";
		reg = <0x70>;
		si5338,init="always"; /* initialize PLL if chip was not programmed, wait for lock. Other option is 'if off' */
		/* low-level masked register writes, may be used to load frequency plan */
		/si5338,configuration_data=< 0x1ffcf0 >;/ /* just for testing: write data 0xfc with write enable mask 0xf0 to register 0x01f */
		si5338,in_frequency3= < 25000000>; /* 25MHz on input 3 (other inputs are '12",'4','56' and '12xo' */
		/* PLL may be set either directly (pll_freq_fract,pll_freq_int) or to match some output (pll_by_out_fract, pll_by_out_int)
		* _int suffix forces to find integer divisors, _fract - allows fractional ones */
		si5338,pll_by_out_int=<150000000>; /* 150Mhz May have 3 values: integer, nominator and denominator */
		si5338,out3_freq_int= <150000000>; /* 150Mhz. May have 3 values: integer, nominator and denominator */
		si5338,out2_select= "in3/2/32"; /* connect out2 to IN3, divided by 2 (input stage) and then by 32 (output stage)*/
		si5338,2V5_LVPECL= <1 2>; /* set output standard for channels 1 and 2 */
		si5338,1V5_HSTL_A+= <0>; /* set output standard for channel 0, only A output is used (noninverted) */
		si5338,1V8_LVDS= <3>;
		/* Disabled state for outputs: */
		si5338,dis_hi-z= <0 1 2 3>; /* Disabled state for listed outputs, also possible: "dis_hi-z","dis_low","dis_high","dis_always_on" */
		si5338,output_en= < 3>; /* Which outputs should be initially enabled */
		si5338,spread_spectrum_3= <1 50 31500>; /* Set spread spectrum for channel3 : enabled, 0.5%, 31.5KHz */
		si5338,out0_freq_int= <15000000>; /* 15Mhz to output 0 */
		si5338,spread_spectrum_0= <1 500 31500>; /* Set spread spectrum for channel0 : enabled, 5%, 31.5KHz - high value, for testing */
		};

		ltc3589@34 {
		compatible = "ltc,ltc3589";
		reg = <0x34>;
		};

		gpio@20{
		compatible = "ti,tca6408";
		reg = <0x20>;
		};
		gpio@21{
		compatible = "ti,tca6408";
		reg = <0x21>;
		};
		gpio@25{
		compatible = "nxp,pca8574";
		reg = <0x25>;
		};
		/* Use 'spd' instead of '24c02' for read only access*/
		stts2002@31 {
		compatible = "at,24c02";
		reg = <0x31>;
		};
		hwmon@1a { /hwmon@19/
		compatible = "stm,jc42";
		reg = <0x1a>;
		};
		};

		ps7_ethernet_0: ps7-ethernet@e000b000 {
		local-mac-address = [00 0e 64 10 00 00];
		phy-handle = <&phy3>;
		phy-mode = "rgmii-id";
		mdio {
		#address-cells = <1>;
		#size-cells = <0>;
		phy3: phy@3 {
		compatible = "atheros,8035";
		device_type = "ethernet-phy";
		reg = <0x3>;
		};
		};
		};

		ps7_smcc_0: ps7-smcc@e000e000 {
		ps7_nand_0: ps7-nand@e1000000 {
		compatible = "arm,pl353-nand-r2p1";
		reg = < 0xe1000000 0x1000000 >;
		/arm,nand-clk-freq-hz = <0x5f5e100>;/
		arm,nand-width = <0x8>;
		arm,nand-cycle-t0 = <0x4>;
		arm,nand-cycle-t1 = <0x4>;
		arm,nand-cycle-t2 = <0x1>;
		arm,nand-cycle-t3 = <0x2>;
		arm,nand-cycle-t4 = <0x2>;
		arm,nand-cycle-t5 = <0x2>;
		arm,nand-cycle-t6 = <0x4>;
		#address-cells = <0x1>;
		#size-cells = <0x1>;
		partition@0 {
		label = "u-boot-spl";
		reg = <0x0 0x100000>;/1MB for backup spl image(s)/
		};
		partition@1 {
		label = "u-boot";
		reg = <0x100000 0x400000>;/4MB/
		};
		partition@2 {
		label = "device-tree";
		reg = <0x500000 0x100000>;/1MB/
		};
		partition@3 {
		label = "kernel";
		reg = <0x600000 0x1000000>;/16MB/
		};
		partition@4 {
		label = "rootfs";
		reg = <0x1600000 0x10000000>;/256MB/
		};
		} ;
		} ;

		elphel_ahci: elphel-ahci@80000000 {
		compatible = "elphel,elphel-ahci";
		interrupt-parent = <&ps7_scugic_0>;
		interrupts = <0x0 0x1d 0x4>; /* interrupt number (middle of 3) is by 0x20 less, than shown as ID in TRM */
		reg = <0x80000000 0x1000>;
		clb_offs = <0x800>;
		fb_offs = <0xc00>;
		};
		};

		elphel393_pwr: elphel393-pwr@0 {
		compatible = "elphel,elphel393-pwr-1.00";
		elphel393_pwr,simulate= <0>;
		elphel393_pwr,i2c_chips= <0x20 0x21 0x25 0x34>;
		elphel393_pwr,vp15.r1= <357000>;
		elphel393_pwr,vp15.r2= <287000>;
		elphel393_pwr,vcc_sens01.r1= <787000>;
		elphel393_pwr,vcc_sens01.r2= <287000>;
		elphel393_pwr,vcc_sens23.r1= <787000>;
		elphel393_pwr,vcc_sens23.r2= <287000>;
		elphel393_pwr,vp5.r1= <523000>;
		elphel393_pwr,vp5.r2= <100000>;
		elphel393_pwr,vldo18.r1= <357000>;
		elphel393_pwr,vldo18.r2= <287000>;
		elphel393_pwr,channels_disable= "vcc_sens23 vp33sens23 vcc_sens01 vp33sens01";
		elphel393_pwr,pinstrapped_oven= <1>;
		elphel393_pwr,vcc_sens01_mv= <2800>; /* set sensor intreface voltage to 2.8V */
		elphel393_pwr,channels_enable= "vp5";
		/* elphel393_pwr,channels_enable= "vcc_sens01 vp33sens01"; */
		} ;

		elphel393_mem: elphel393-mem@0 {
		compatible = "elphel,elphel393-mem-1.00";
		/memsize = <25600>;/
		memsize = <76800>;
		} ;

		elphel393_init: elphel393-init {
		compatible = "elphel,elphel393-init-1.00";
		} ;

		elphel393_circbuf: elphel393-circbuf@0 {
		compatible = "elphel,elphel393-circbuf-1.00";
		/* set this to "disable" to disable drivers */
		status = "okay";
		interrupt-parent = <&ps7_scugic_0>;
		/* interrupt number (middle of 3) is by 0x20 less, than shown as ID in TRM */
		interrupts = <0x0 0x34 0x4>, <0x0 0x35 0x4>, <0x0 0x36 0x4>, <0x0 0x37 0x4>,
		<0x0 0x38 0x4>, <0x0 0x39 0x4>, <0x0 0x3A 0x4>, <0x0 0x3B 0x4>;
		/* reg = <0x80000000 0x1000>; */
		interrupt-names = "frame_sync_irq_0", "frame_sync_irq_1", "frame_sync_irq_2", "frame_sync_irq_3",
		"compr_irq_0", "compr_irq_1", "compr_irq_2", "compr_irq_3";
		};

		elphel393_logger: elphel393-logger@0 {
		compatible = "elphel,elphel393-logger-1.00";
		/* set this to "disable" to disable drivers */
		status = "okay";
		interrupt-parent = <&ps7_scugic_0>;
		/* interrupt number (middle of 3) is by 0x20 less, than shown as ID in TRM */
		interrupts = <0x0 0x21 0x4>, <0x0 0x22 0x4>, <0x0 0x23 0x4>, <0x0 0x24 0x4>;
		/* reg = <0x80000000 0x1000>; */
		interrupt-names = "mult_saxi_0", "mult_saxi_1", "mult_saxi_2", "mult_saxi_3";
		};

		elphel393_videomem: elphel393-videomem@0 {
		compatible = "elphel,elphel393-videomem-1.00";
		/* set this to "disable" to disable drivers */
		status = "okay";
		interrupt-parent = <&ps7_scugic_0>;
		/* interrupt number (middle of 3) is by 0x20 less, than shown as ID in TRM */
		interrupts = <0x0 0x20 0x4>;
		/* reg = <0x80000000 0x1000>; */
		interrupt-names = "membridge_irq";
		/* maximal dimesions that use all 512M memory for 4 channels. May be changed when doing processing*/
		frame_full_width = <8192>; /* in bytes, will be transformed to bursts (16 bytes). 1 memory page is 2048 bytes (128 bursts) */
		frame_height = <8192>; /* in pixel lines */
		frames_in_buffer = <2>; /* Each channel has this number of frames in buffer */

		frame_start_chn0 = <0x00000000>; /* Channel 0 frame start (in bytes) */
		frame_start_chn1 = <0x08000000>; /* Channel 1 frame start (in bytes) */
		frame_start_chn2 = <0x10000000>; /* Channel 2 frame start (in bytes) */
		frame_start_chn3 = <0x18000000>; /* Channel 3 frame start (in bytes) */
		frame_full_width_chn0 = <8192>; /* Channel 0 frame full width (in bytes). 1 memory page is 2048 bytes (128 bursts) */
		frame_full_width_chn1 = <8192>; /* Channel 1 frame full width (in bytes). 1 memory page is 2048 bytes (128 bursts) */
		frame_full_width_chn2 = <8192>; /* Channel 2 frame full width (in bytes). 1 memory page is 2048 bytes (128 bursts) */
		frame_full_width_chn3 = <8192>; /* Channel 3 frame full width (in bytes). 1 memory page is 2048 bytes (128 bursts) */
		frame_height_chn0 = <8192>; /* Channel 0 maximal frame height in pixel lines */
		frame_height_chn1 = <8192>; /* Channel 1 maximal frame height in pixel lines */
		frame_height_chn2 = <8192>; /* Channel 2 maximal frame height in pixel lines */
		frame_height_chn3 = <8192>; /* Channel 3 maximal frame height in pixel lines */
		frames_in_buffer_chn0 = <2>; /* Number of frames in channel 0 buffer */
		frames_in_buffer_chn1 = <2>; /* Number of frames in channel 1 buffer */
		frames_in_buffer_chn2 = <2>; /* Number of frames in channel 2 buffer */
		frames_in_buffer_chn3 = <2>; /* Number of frames in channel 3 buffer */
		};

		elphel393_detect_sensors: elphel393-detect_sensors@0 {
		compatible = "elphel,elphel393-detect_sensors-1.00";
		elphel393-detect_sensors,port-mux = "none none none none"; /* "none", "detect" or "mux10359" */
		elphel393-detect_sensors,sensors = "mt9p006", // Line per port, may contain up to 4 sensors (3 with 10359)
		"mt9p006",
		"mt9p006",
		"mt9p006";
		};

		elphel393_sensor_i2c: elphel393-sensor-i2c@0 {
		compatible = "elphel,elphel393-sensor-i2c-1.00";
		/* Add known devices: name, slave address (7-bit), number of address bytes, number of data bytes, SCL frequency (kHz) */
		elphel393-sensor-i2c,i2c_devices = "mt9f002 0x10 2 2 500",
		"mt9p006 0x48 1 2 500",
		"el10359 0x08 1 2 500",
		"pca9500_eeprom 0x50 1 1 100",
		"cy22393 0x69 1 1 100";
		} ;

		framepars_operations: elphel393-framepars@0 {
		compatible = "elphel,elphel393-framepars-1.00";
		};

		histograms_operations: elphel393-histograms@0 {
		compatible = "elphel,elphel393-histograms-1.00";
		};

		gamma_tables_operations: elphel393-gamma_tables@0 {
		compatible = "elphel,elphel393-gamma_tables-1.00";
		};

		elphel393_mt9x001: elphel393-mt9x001@0 {
		compatible = "elphel,elphel393-mt9x001-1.00";
		};

		klogger_393: klogger-393@0 {
		compatible = "elphel,klogger-393-1.00";
		klogger-393,buffer_size = <1048576>;
		} ;


		};
		No newline at end of file

src/arch/arm/boot/dts/elphel393_1_mt9p006.dts

+11 −4

Original line number	Diff line number	Diff line
		@@ -265,7 +265,10 @@
		elphel393-sensor-i2c,i2c_devices = "mt9f002 0x10 2 2 500",
		"mt9p006 0x48 1 2 500",
		"el10359 0x08 1 2 500",
		"el10359_32 0x08 1 4 500",
		"pca9500_eeprom 0x50 1 1 100",
		"sensor_eeprom 0x50 1 1 100",
		"sensor_temp 0x18 1 2 100",
		"cy22393 0x69 1 1 100";
		} ;

		@@ -285,6 +288,10 @@
		compatible = "elphel,elphel393-mt9x001-1.00";
		};

		elphel393_clock10359:elphel393-clock10359@0{
		compatible = "elphel,elphel393_clock10359-1.00";
		};

		klogger_393: klogger-393@0 {
		compatible = "elphel,klogger-393-1.00";
		klogger-393,buffer_size = <1048576>;

src/arch/arm/boot/dts/elphel393_4_mt9p006.dts

+11 −4

Original line number	Diff line number	Diff line
		@@ -265,7 +265,10 @@
		elphel393-sensor-i2c,i2c_devices = "mt9f002 0x10 2 2 500",
		"mt9p006 0x48 1 2 500",
		"el10359 0x08 1 2 500",
		"el10359_32 0x08 1 4 500",
		"pca9500_eeprom 0x50 1 1 100",
		"sensor_eeprom 0x50 1 1 100",
		"sensor_temp 0x18 1 2 100",
		"cy22393 0x69 1 1 100";
		} ;

		@@ -285,6 +288,10 @@
		compatible = "elphel,elphel393-mt9x001-1.00";
		};

		elphel393_clock10359:elphel393-clock10359@0{
		compatible = "elphel,elphel393_clock10359-1.00";
		};

		klogger_393: klogger-393@0 {
		compatible = "elphel,klogger-393-1.00";
		klogger-393,buffer_size = <1048576>;

Admin message