Commit c6e51532 authored by Andrey Filippov's avatar Andrey Filippov

tweeked configurations

parent 04f45016
......@@ -42,9 +42,8 @@
#define CONFIG_EZYNQ_DUMP_OCM_LOW 0x0 /* OCM dump start (deafault 0) */
#define CONFIG_EZYNQ_DUMP_OCM_HIGH 0x2ff /* OCM dump end (deafault 0x2ff, full - 0x2ffff) */
#define CONFIG_EZYNQ_DUMP_DDR_LOW 0x4001014 /* DDR dump start (deafault 0x4000000, start of the OCM copy) */
//#define CONFIG_EZYNQ_DUMP_DDR_HIGH 0x400152f /* DDR dump end (deafault 0x40002ff) */
#define CONFIG_EZYNQ_DUMP_DDR_HIGH 0x300152f /* DDR dump end (deafault 0x40002ff) */
#define CONFIG_EZYNQ_DUMP_DDR_LOW 0x4000000 /* DDR dump start (deafault 0x4000000, start of the OCM copy) */
#define CONFIG_EZYNQ_DUMP_DDR_HIGH 0x40002ff /* DDR dump end (deafault 0x40002ff) */
#endif
/* Turning LED on/off at different stages of the boot process. Requires CONFIG_EZYNQ_LED_DEBUG and CONFIG_EZYNQ_BOOT_DEBUG to be set
If defined, each can be 0,1, ON or OFF */
......@@ -60,7 +59,7 @@
#define CONFIG_EZYNQ_LED_CHECKPOINT_10 ON /* Before remapping OCM0-OCM2 high */
#define CONFIG_EZYNQ_LED_CHECKPOINT_11 ON /* After remapping OCM0-OCM2 high */
#define CONFIG_EZYNQ_LED_CHECKPOINT_12 ON /* Before leaving lowlevel_init() */
#define CONFIG_EZYNQ_LAST_PRINT_DEBUG N /* 'Output to UART before exiting arch_cpu_init() */
#define CONFIG_EZYNQ_LAST_PRINT_DEBUG Y /* 'Output to UART before exiting arch_cpu_init() */
/* MIO configuration */
#define CONFIG_EZYNQ_OCM /* not used */
#define CONFIG_EZYNQ_MIO_0_VOLT 1.8
......
......@@ -74,12 +74,6 @@
#define CONFIG_EZYNQ_MIO_SDIO_0 40 /* 16,28,40 */
#define CONFIG_EZYNQ_MIO_SDIO_0__SLOW
#define CONFIG_EZYNQ_MIO_SDIO_0__PULLUP
#define CONFIG_EZYNQ_MIO_SDIO_0 40 /* 16,28,40 */
#define CONFIG_EZYNQ_MIO_SDIO_0__SLOW
#define CONFIG_EZYNQ_MIO_SDIO_0__PULLUP
#define CONFIG_EZYNQ_MIO_SDIO_0 40 /* 16,28,40 */
#define CONFIG_EZYNQ_MIO_SDIO_0__SLOW
#define CONFIG_EZYNQ_MIO_SDIO_0__PULLUP
#define CONFIG_EZYNQ_MIO_SDCD_0 46 /* any but 7,8 */
#define CONFIG_EZYNQ_MIO_SDCD_0__PULLUP
#define CONFIG_EZYNQ_MIO_SDWP_0 50 /* #any but 7,8 */
......
Markdown is supported
0% or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment