Skip to content

E
ezynq
Commit 94448d0b authored by Andrey Filippov's avatar Andrey Filippov
Browse files
Options

updating configuration for the microzed board

parent 20e75934
Show whitespace changes
Inline Side-by-side
Showing with 72 additions and 40 deletions
u-boot-tree/include/configs/ezynq/ezynq393.h
View file @ 94448d0b
......@@ -70,10 +70,8 @@
#define CONFIG_EZYNQ_MIO_ETH_0__SLOW
#define CONFIG_EZYNQ_MIO_ETH_MDIO__SLOW
#define CONFIG_EZYNQ_MIO_USB_0__SLOW
#define CONFIG_EZYNQ_MIO_USB_0__PULLUP
#define CONFIG_EZYNQ_MIO_SDIO_0 40 /* 16,28,40 */
#define CONFIG_EZYNQ_MIO_SDIO_0__SLOW
#define CONFIG_EZYNQ_MIO_SDIO_0__PULLUP
......@@ -192,8 +190,6 @@ output (or undefined) - off
#define CONFIG_EZYNQ_CLK_COMPLIANCE_PERCENT 5.0 /* Allow exceeding maximal limits by this margin (percent */
/* Board PCB layout parameters (not yet used) */
#define CONFIG_EZYNQ_DDR_BOARD_DELAY0 0.0
#define CONFIG_EZYNQ_DDR_BOARD_DELAY1 0.0
......@@ -214,20 +210,6 @@ output (or undefined) - off
/* Below will overwrite calculated values (not yet calculated) */
#if 1 /*testing old version */
/* LED will be ON */
// #define CONFIG_EZYNQ_MIO_INOUT_53 OUT /* Make output, do not set data. Will be set after debug will be over */
/* #define CONFIG_EZYNQ_MIO_GPIO_OUT_53 0 */ /* Set selected GPIO output to 0/1 */
#undef CONFIG_EZYNQ_DDR_DS_CKE
#define CONFIG_EZYNQ_DDR_DS_CKE 4 /* CKE min pulse width (in tCK) */
// #undef CONFIG_EZYNQ_DDR_DS_WLMRD
// #define CONFIG_EZYNQ_DDR_DS_WLMRD 22 /* Write leveling : time to the first DQS rising edge (cycles). */
/* #define CONFIG_EZYNQ_LED_DEBUG 53 */ /* toggle LED during boot - temporary, normal use - MDIO_D */
#define CONFIG_EZYNQ_UART_DEBUG_USE_LED N /* turn on/off LED while waiting for transmit FIFO not full */
#define CONFIG_EZYNQ_SILICON 3 /* 3 */ /* Silicon revision */
......@@ -262,7 +244,7 @@ output (or undefined) - off
#define CONFIG_EZYNQ_PHY_PHY_WR_DATA_SLAVE_RATIO_3 0x40 /* Ratio for write data slave DLL (256 - clock period), slice 3 */
#define CONFIG_EZYNQ_PHY_PHY_CTRL_SLAVE_RATIO 0x80 /* Ratio for address/command (256 - clock period) */
#define CONFIG_EZYNQ_PHY_INVERT_CLK N /* RInvert CLK out (if clk can arrive to DRAM chip earlier/at the same time as DQS) */
#define CONFIG_EZYNQ_PHY_INVERT_CLK N /* Invert CLK out (if clk can arrive to DRAM chip earlier/at the same time as DQS) */
#else
#define CONFIG_EZYNQ_MIO_ETH_MDIO__SLOW
......@@ -294,7 +276,7 @@ output (or undefined) - off
#define CONFIG_EZYNQ_PHY_PHY_WR_DATA_SLAVE_RATIO_3 0xc7 /* Ratio for write data slave DLL (256 - clock period), slice 3 */
#define CONFIG_EZYNQ_PHY_PHY_CTRL_SLAVE_RATIO 0x100 /* Ratio for address/command (256 - clock period) */
#define CONFIG_EZYNQ_PHY_INVERT_CLK /* RInvert CLK out (if clk can arrive to DRAM chip earlier/at the same time as DQS) */
#define CONFIG_EZYNQ_PHY_INVERT_CLK /* Invert CLK out (if clk can arrive to DRAM chip earlier/at the same time as DQS) */
#endif
......
u-boot-tree/include/configs/ezynq/zed_ezynq.h
View file @ 94448d0b
......@@ -17,6 +17,7 @@
#define __CONFIG_EZYNQ_H
#define CONFIG_EZYNQ
/* Boot image cionfiguration parameters */
#define CONFIG_EZYNQ_BOOT_USERDEF 0x1010000 /* 0x1234567 will be saved in the file header */
......@@ -26,18 +27,29 @@
#define CONFIG_EZYNQ_RESERVED44 0 /* documented as 0, but actually 1 */
/* Boot debug setup */
#define CONFIG_EZYNQ_BOOT_DEBUG /* configure UARTx and send register dumps there.*/
#define CONFIG_EZYNQ_BOOT_DEBUG Y /* configure UARTx and send register dumps there.*/
#define CONFIG_EZYNQ_LOCK_SLCR OFF /* Lock SLCR registers when all is done. */
#define CONFIG_EZYNQ_LED_DEBUG 47 /* toggle LED during boot */
#define CONFIG_EZYNQ_UART_DEBUG_USE_LED /* turn on/off LED while waiting for transmit FIFO not full */
#define CONFIG_EZYNQ_DUMP_SLCR_EARLY /* Dump SLCR registers as soon as UART is initialized (depends on CONFIG_EZYNQ_BOOT_DEBUG) */
#define CONFIG_EZYNQ_DUMP_DDRC_EARLY /* Dump DDRC registers as soon as UART is initialized (depends on CONFIG_EZYNQ_BOOT_DEBUG) */
#define CONFIG_EZYNQ_DUMP_SLCR_LATE /* Dump SLCR registers after DDR memory is initialized (depends on CONFIG_EZYNQ_BOOT_DEBUG) */
#define CONFIG_EZYNQ_DUMP_DDRC_LATE /* Dump DDRC registers after DDR memory is initialized (depends on CONFIG_EZYNQ_BOOT_DEBUG) */
#define CONFIG_EZYNQ_DUMP_SLCR_EARLY N /* Dump SLCR registers as soon as UART is initialized (depends on CONFIG_EZYNQ_BOOT_DEBUG) */
#define CONFIG_EZYNQ_DUMP_DDRC_EARLY N /* Dump DDRC registers as soon as UART is initialized (depends on CONFIG_EZYNQ_BOOT_DEBUG) */
#define CONFIG_EZYNQ_DUMP_SLCR_LATE N /* Dump SLCR registers after DDR memory is initialized (depends on CONFIG_EZYNQ_BOOT_DEBUG) */
#define CONFIG_EZYNQ_DUMP_DDRC_LATE N /* Dump DDRC registers after DDR memory is initialized (depends on CONFIG_EZYNQ_BOOT_DEBUG) */
#define CONFIG_EZYNQ_DUMP_TRAINING_EARLY N /* Training results registers before DDRC initialization */
#define CONFIG_EZYNQ_DUMP_TRAINING_LATE Y /* Training results registers after DDRC initialization */
#define CONFIG_EZYNQ_DUMP_OCM y /* Dump (some of) OCM data */
#define CONFIG_EZYNQ_DUMP_DDR y /* Dump (some of) DDR data */
#if 1
#define CONFIG_EZYNQ_DUMP_OCM_LOW 0x0 /* OCM dump start (deafault 0) */
#define CONFIG_EZYNQ_DUMP_OCM_HIGH 0x2ff /* OCM dump end (deafault 0x2ff, full - 0x2ffff) */
#define CONFIG_EZYNQ_DUMP_DDR_LOW 0x4000000 /* DDR dump start (deafault 0x4000000, start of the OCM copy) */
#define CONFIG_EZYNQ_DUMP_DDR_HIGH 0x40002ff /* DDR dump end (deafault 0x40002ff) */
#endif
/* Turning LED on/off at different stages of the boot process. Requires CONFIG_EZYNQ_LED_DEBUG and CONFIG_EZYNQ_BOOT_DEBUG to be set
If defined, each can be 0,1, ON or OFF */
#define CONFIG_EZYNQ_LED_CHECKPOINT_1 ON /* in RBL setup, as soon as MIO is programmed */
#define CONFIG_EZYNQ_LED_CHECKPOINT_1 OFF /* in RBL setup, as soon as MIO is programmed, should be OFF to use GPIO */
#define CONFIG_EZYNQ_LED_CHECKPOINT_2 OFF /* First after getting to user code */
#define CONFIG_EZYNQ_LED_CHECKPOINT_3 ON /* After setting clock registers */
#define CONFIG_EZYNQ_LED_CHECKPOINT_4 OFF /* After PLL bypass is OFF */
......@@ -49,6 +61,7 @@
#define CONFIG_EZYNQ_LED_CHECKPOINT_10 OFF /* Before remapping OCM0-OCM2 high */
#define CONFIG_EZYNQ_LED_CHECKPOINT_11 ON /* After remapping OCM0-OCM2 high */
#define CONFIG_EZYNQ_LED_CHECKPOINT_12 OFF /* Before leaving lowlevel_init() */
#define CONFIG_EZYNQ_LAST_PRINT_DEBUG y /* 'Output to UART before exiting arch_cpu_init() */
/* MIO configuration */
#define CONFIG_EZYNQ_OCM /* not used */
#define CONFIG_EZYNQ_MIO_0_VOLT 3.3
......@@ -61,6 +74,12 @@
#define CONFIG_EZYNQ_MIO_SDIO_0 40 /* 16,28,40 */
#define CONFIG_EZYNQ_MIO_SDIO_0__SLOW
#define CONFIG_EZYNQ_MIO_SDIO_0__PULLUP
#define CONFIG_EZYNQ_MIO_SDIO_0 40 /* 16,28,40 */
#define CONFIG_EZYNQ_MIO_SDIO_0__SLOW
#define CONFIG_EZYNQ_MIO_SDIO_0__PULLUP
#define CONFIG_EZYNQ_MIO_SDIO_0 40 /* 16,28,40 */
#define CONFIG_EZYNQ_MIO_SDIO_0__SLOW
#define CONFIG_EZYNQ_MIO_SDIO_0__PULLUP
#define CONFIG_EZYNQ_MIO_SDCD_0 46 /* any but 7,8 */
#define CONFIG_EZYNQ_MIO_SDCD_0__PULLUP
#define CONFIG_EZYNQ_MIO_SDWP_0 50 /* #any but 7,8 */
......@@ -72,15 +91,10 @@
/*
Red LED - pullup, input - on,
output (or undefined) - off
#define CONFIG_EZYNQ_MIO_PULLUP_EN_47
#define CONFIG_EZYNQ_MIO_PULLUP_DIS_0
#define CONFIG_EZYNQ_MIO_INOUT_47 OUT
#define CONFIG_EZYNQ_MIO_INOUT_47 IN
#define CONFIG_EZYNQ_MIO_INOUT_47 BIDIR
*/
/* DDR chip independent */
#define CONFIG_EZYNQ_DDR_ENABLE Y /* Enable DDR memory */
/* Only specify CONFIG_EZYNQ_DDR_FREQ_MHZ if you want the DDR frequency used for timing calculations is different from actual */
/* #define CONFIG_EZYNQ_DDR_FREQ_MHZ 533.333333 */ /* DDR clock frequency in MHz, this value overwrites the one calculated by the PLL/clock setup */
......@@ -174,8 +188,6 @@ output (or undefined) - off
#define CONFIG_EZYNQ_CLK_COMPLIANCE_PERCENT 5.0 /* Allow exceeding maximal limits by this margin (percent */
/* Board PCB layout parameters (not yet used) */
#define CONFIG_EZYNQ_DDR_BOARD_DELAY0 0.0
#define CONFIG_EZYNQ_DDR_BOARD_DELAY1 0.0
......@@ -198,6 +210,42 @@ output (or undefined) - off
#define CONFIG_EZYNQ_DDR_RAM_BASEADDR 0x00100000
#define CONFIG_EZYNQ_DDR_RAM_HIGHADDR 0x3FFFFFFF
*/
/* Below will overwrite calculated values (not yet calculated) */
#define CONFIG_EZYNQ_SILICON 3 /* 3 */ /* Silicon revision */
#define CONFIG_EZYNQ_PHY_WRLV_INIT_RATIO_0 0x0 /* Initial ratio for write leveling FSM, slice 0 */
#define CONFIG_EZYNQ_PHY_WRLV_INIT_RATIO_1 0x0 /* Initial ratio for write leveling FSM, slice 1 */
#define CONFIG_EZYNQ_PHY_WRLV_INIT_RATIO_2 0x0 /* Initial ratio for write leveling FSM, slice 2 */
#define CONFIG_EZYNQ_PHY_WRLV_INIT_RATIO_3 0x0 /* Initial ratio for write leveling FSM, slice 3 */
#define CONFIG_EZYNQ_PHY_GTLV_INIT_RATIO_0 0x0 /* Initial ratio for gate leveling FSM, slice 0 */
#define CONFIG_EZYNQ_PHY_GTLV_INIT_RATIO_1 0x0 /* Initial ratio for gate leveling FSM, slice 1 */
#define CONFIG_EZYNQ_PHY_GTLV_INIT_RATIO_2 0x0 /* Initial ratio for gate leveling FSM, slice 2 */
#define CONFIG_EZYNQ_PHY_GTLV_INIT_RATIO_3 0x0 /* Initial ratio for gate leveling FSM, slice 3 */
#define CONFIG_EZYNQ_PHY_RD_DQS_SLAVE_RATIO_0 0x35/* Ratio for read DQS slave DLL (256 - clock period), slice 0 */
#define CONFIG_EZYNQ_PHY_RD_DQS_SLAVE_RATIO_1 0x35/* Ratio for read DQS slave DLL (256 - clock period), slice 1 */
#define CONFIG_EZYNQ_PHY_RD_DQS_SLAVE_RATIO_2 0x35/* Ratio for read DQS slave DLL (256 - clock period), slice 2 */
#define CONFIG_EZYNQ_PHY_RD_DQS_SLAVE_RATIO_3 0x35/* Ratio for read DQS slave DLL (256 - clock period), slice 3 */
#define CONFIG_EZYNQ_PHY_WR_DQS_SLAVE_RATIO_0 0x0 /* Ratio for write DQS slave DLL (256 - clock period), slice 0 */
#define CONFIG_EZYNQ_PHY_WR_DQS_SLAVE_RATIO_1 0x0 /* Ratio for write DQS slave DLL (256 - clock period), slice 1 */
#define CONFIG_EZYNQ_PHY_WR_DQS_SLAVE_RATIO_2 0x0 /* Ratio for write DQS slave DLL (256 - clock period), slice 2 */
#define CONFIG_EZYNQ_PHY_WR_DQS_SLAVE_RATIO_3 0x0 /* Ratio for write DQS slave DLL (256 - clock period), slice 3 */
#define CONFIG_EZYNQ_PHY_FIFO_WE_SLAVE_RATIO_0 0x35 /*Ratio for FIFO WE slave DLL (256 - clock period), slice 0 */
#define CONFIG_EZYNQ_PHY_FIFO_WE_SLAVE_RATIO_1 0x35 /*Ratio for FIFO WE slave DLL (256 - clock period), slice 0 */
#define CONFIG_EZYNQ_PHY_FIFO_WE_SLAVE_RATIO_2 0x35 /*Ratio for FIFO WE slave DLL (256 - clock period), slice 0 */
#define CONFIG_EZYNQ_PHY_FIFO_WE_SLAVE_RATIO_3 0x35 /*Ratio for FIFO WE slave DLL (256 - clock period), slice 0 */
#define CONFIG_EZYNQ_PHY_PHY_WR_DATA_SLAVE_RATIO_0 0x40 /* Ratio for write data slave DLL (256 - clock period), slice 0 */
#define CONFIG_EZYNQ_PHY_PHY_WR_DATA_SLAVE_RATIO_1 0x40 /* Ratio for write data slave DLL (256 - clock period), slice 1 */
#define CONFIG_EZYNQ_PHY_PHY_WR_DATA_SLAVE_RATIO_2 0x40 /* Ratio for write data slave DLL (256 - clock period), slice 2 */
#define CONFIG_EZYNQ_PHY_PHY_WR_DATA_SLAVE_RATIO_3 0x40 /* Ratio for write data slave DLL (256 - clock period), slice 3 */
#define CONFIG_EZYNQ_PHY_PHY_CTRL_SLAVE_RATIO 0x80 /* Ratio for address/command (256 - clock period) */
#define CONFIG_EZYNQ_PHY_INVERT_CLK N /* Invert CLK out (if clk can arrive to DRAM chip earlier/at the same time as DQS) */
#endif /* __CONFIG_EZYNQ_H */
u-boot-tree/include/configs/zynq_microzed.h
View file @ 94448d0b
......@@ -30,17 +30,19 @@
#define CONFIG_SYS_NO_FLASH
#define CONFIG_ZYNQ_SDHCI0
//#define CONFIG_ZYNQ_SPI
/* #define CONFIG_ZYNQ_SPI */
//#define CONFIG_NAND_ZYNQ
/* #define CONFIG_NAND_ZYNQ */
#undef CONFIG_SYS_TEXT_BASE
#include <configs/zynq_common.h>
#include <configs/ezynq/ezynq_MT41K256M16RE125.h> /* should be before zed_ezynq.h as it overwrites DDR3L with DDR3 */
#include <configs/ezynq/ezynq_XC7Z010_1CLG400.h>
#include <configs/ezynq/zed_ezynq.h>
//#define CONFIG_CMD_MEMTEST
#undef CONFIG_EZYNQ_BOOT_DEBUG
#if 1
#undef CONFIG_EZYNQ_BOOT_DEBUG Y /* configure UARTx and send register dumps there.*/
#endif
#define CONFIG_CMD_MEMTEST
/* twice slower */
#undef CONFIG_ZYNQ_SERIAL_CLOCK0
......@@ -66,14 +68,14 @@
#if 0
#define CONFIG_SYS_TEXT_BASE 0x04000000 /*with 0x04000000 - does not get to the low_Level_init? */
#else
#define CONFIG_SYS_TEXT_BASE 0x00000000 //0x04000000 with 0x04000000 - does not get to the low_Level_init?
#define CONFIG_SYS_TEXT_BASE 0x00000000
#endif
/*
#define CONFIG_EZYNQ_SKIP_DDR
*/
#define CONFIG_EZYNQ_SKIP_CLK
//undefs
/* undefs */
/* undefs */
/*#undef CONFIG_FS_FAT */
......
Markdown is supported
0% or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment