Initial release of the files

Development of the ROM boot loader header generator for Xilinx Zynq based boards

The included sample zed_ezynq.h provides defines for Microzed board, it is to be included in includes/configs/<boardname>.h

After running

  make <boardname>_congig

and then

  make

the include/autoconf.mk will be generated and you can run

  ezynqcfg.py -c include/autoconf.mk [-o boot_head.bin] [--html u-boot.html [--html-mask 255]] [-v]

This command will generate  boot_head.bin and u-boot.html

When there will be u-boot running from OCM, it will be possible to make a bootable immage with

cat boot_head.bin u-boot.bin > boot.bin

For testing the program it is possible to make a shortcut and substitute the autoconf.mk with a manually edited file,

such as test.mk - it has some examples of other valid defines to fine-tune the hardware configuration

 No newline at end of file

#COnfiguration for the microzed board

CONFIG_EZYNQ_MIO_0_VOLT=3.3

CONFIG_EZYNQ_MIO_1_VOLT=1.8

#CONFIG_EZYNQ_MIO_0_PULLUP=y #default pullup for MIO0 - may be overwritten for individual pins

#CONFIG_EZYNQ_MIO_1_PULLUP=y #default pullup for MIO0 - may be overwritten for individual pins

#I/O standards will default to 1.3/2.5/3.3 according to MIO voltage

#CONFIG_EZYNQ_QUADSPI_0 = y 

CONFIG_EZYNQ_QUADSPI_0__ATTRIB = SLOW 

#CONFIG_EZYNQ_QUADSPI_1 = y

#CONFIG_EZYNQ_QUADSPI_FBCLK = y

#CONFIG_EZYNQ_MIO_ETH_0=y

 CONFIG_EZYNQ_MIO_ETH_0__ATTRIB= SLOW

#CONFIG_EZYNQ_MIO_ETH_1=y

 CONFIG_EZYNQ_MIO_ETH_MDIO__ATTRIB= SLOW

 CONFIG_EZYNQ_MIO_USB_0__ATTRIB= SLOW

#CONFIG_EZYNQ_MIO_USB_1=y

#CONFIG_EZYNQ_MIO_SPI_0=16 #16,28,40

#CONFIG_EZYNQ_MIO_SPI_1=10 #10,22,34,46

 CONFIG_EZYNQ_MIO_SDIO_0=40 #16,28,40

 CONFIG_EZYNQ_MIO_SDIO_0__ATTRIB=SLOW

#CONFIG_EZYNQ_MIO_SDIO_1=10 #10,22,34,46

 CONFIG_EZYNQ_MIO_SDCD_0=46 #any but 7,8

 CONFIG_EZYNQ_MIO_SDWP_0=50 #any but 7,8

#CONFIG_EZYNQ_MIO_SDCD_1=48 #any but 7,8

#CONFIG_EZYNQ_MIO_SDWP_1=48 #any but 7,8

#CONFIG_EZYNQ_MIO_SDPWR_0=48 #any even

#CONFIG_EZYNQ_MIO_SDPWR_1=49 #any odd

#CONFIG_EZYNQ_NOR=y

#CONFIG_EZYNQ_NOR_A25=y # either A25 or CS1

#CONFIG_EZYNQ_NOR_CS1=y # either A25 or CS1

#CONFIG_EZYNQ_NAND=y

#CONFIG_EZYNQ_NAND__BUSY=free # debugging software

#CONFIG_EZYNQ_NAND16=y

#CONFIG_EZYNQ_MIO_CAN_0=46 # 10+4*N

#CONFIG_EZYNQ_MIO_CAN_1=44 #  8+4*N

#CONFIG_EZYNQ_MIO_CAN_ECLK_0=48 # any Just GPIO?

#CONFIG_EZYNQ_MIO_CAN_ECLK_1=49 # any Just GPIO?

#CONFIG_EZYNQ_MIO_UART_0=46 # 10+4*N

CONFIG_EZYNQ_MIO_UART_1=48 #  8+4*N

#CONFIG_EZYNQ_MIO_I2C_0=50 # 10+4*N

#CONFIG_EZYNQ_MIO_I2C_1=44 # 12+4*N

#CONFIG_EZYNQ_MIO_TTC_0=18 # 18+12*N

#CONFIG_EZYNQ_MIO_TTC_1=16 # 16+12*N

#CONFIG_EZYNQ_MIO_SWDT= 14 # 14+12*N, 52

#CONFIG_EZYNQ_MIO_PJTAG=10 # 10+12*N

#CONFIG_EZYNQ_MIO_TPUI= 2 # TODO

#the following will be applied after devices above

#each of the interfaces above can have "__<pinname>" to mix same pins from different groups

#"__<pinname>=-1" - remove specified pin from the interface (do not use it)

#just for testing

#CONFIG_EZYNQ_MIO_TPUI=12 #24

#CONFIG_EZYNQ_MIO_TPUI__CLK0=12 #24

#CONFIG_EZYNQ_MIO_TPUI__CTL=25 #13

#CONFIG_EZYNQ_MIO_TPUI__DATA0=14 #26

#CONFIG_EZYNQ_MIO_TPUI__DATA1=15 #27

#CONFIG_EZYNQ_MIO_TPUI__DATA2=10 #22

#CONFIG_EZYNQ_MIO_TPUI__DATA3=11 #23

#CONFIG_EZYNQ_MIO_IOSTD_LVCMOS18_01= y # will overwrite defaults, last numeric specifies MIO pin number

#CONFIG_EZYNQ_MIO_IOSTD_LVCMOS25_15= y # will overwrite defaults

#CONFIG_EZYNQ_MIO_IOSTD_LVCMOS33_2= y # will overwrite defaults

#CONFIG_EZYNQ_MIO_IOSTD_HSTL_3=     y # will overwrite defaults

#CONFIG_EZYNQ_MIO_IOSTD_HSTLDIS_4= y # will overwrite defaults

#CONFIG_EZYNQ_MIO_PULLUP_EN_5=      y # will overwrite defaults

#CONFIG_EZYNQ_MIO_PULLUP_DIS_0=     y # will overwrite defaults

#CONFIG_EZYNQ_MIO_FAST_7=           y # will overwrite defaults

#CONFIG_EZYNQ_MIO_SLOW_8=           y # will overwrite defaults

#CONFIG_EZYNQ_MIO_INOUT_2=          OUT # 'IN', 'BIDIR'

#CONFIG_EZYNQ_MIO_INOUT_15=          OUT # 'IN', 'BIDIR'

#CONFIG_EZYNQ_MIO_INOUT_0=          IN # 'IN', 'BIDIR'

#CONFIG_EZYNQ_MIO_GPIO_OUT_02=       0 # Set selected GPIO output to 0/1

#CONFIG_EZYNQ_MIO_GPIO_OUT_15=       1 # Set selected GPIO output to 0/1

## Boot image parameters

CONFIG_EZYNQ_BOOT_USERDEF=           0x1234567 # will be saved in the file header

CONFIG_EZYNQ_BOOT_OCM_OFFSET=        0x8C0   # start of OCM data relative to the flash image start >=0x8C0, 63-bytes aligned

CONFIG_EZYNQ_BOOT_OCM_IMAGE_LENGTH=  0#0x30000 # number of bytes to load to the OCM memory, <= 0x30000 

CONFIG_EZYNQ_START_EXEC=             0x00 # start of execution address 

/*

 * (C) Copyright 2013 Elphel, Inc.

 *

 * Configuration for Microzed RBL header

 *

 * This program is free software; you can redistribute it and/or

 * modify it under the terms of the GNU General Public License as

 * published by the Free Software Foundation; either version 3 of

 * the License, or (at your option) any later version.

 *

 * You should have received a copy of the GNU General Public License

 * along with this program; if not, write to the Free Software

 * Foundation, Inc., 59 Temple Place, Suite 330, Boston,

 * MA 02111-1307 USA

 */

#ifndef __CONFIG_EZYNQ_H

#define __CONFIG_EZYNQ_H

#define CONFIG_EZYNQ_OCM

#define CONFIG_EZYNQ_MIO_0_VOLT           3.3

#define CONFIG_EZYNQ_MIO_1_VOLT           1.8

#define CONFIG_EZYNQ_QUADSPI_0__ATTRIB    SLOW 

#define CONFIG_EZYNQ_MIO_ETH_0__ATTRIB    SLOW

#define CONFIG_EZYNQ_MIO_ETH_MDIO__ATTRIB SLOW

#define CONFIG_EZYNQ_MIO_USB_0__ATTRIB    SLOW

#define CONFIG_EZYNQ_MIO_SDIO_0           40 // 16,28,40

#define CONFIG_EZYNQ_MIO_SDIO_0__ATTRIB   SLOW

#define CONFIG_EZYNQ_MIO_SDCD_0           46 //#any but 7,8

#define CONFIG_EZYNQ_MIO_SDWP_0           50 //#any but 7,8

#define CONFIG_EZYNQ_MIO_UART_1           48 //#  8+4*N

/*

 //#debug

//#define CONFIG_EZYNQ_UART_LOOPBACK_1=y

Red LED - pullup, input - on,

output (or undefined) -   off

#define CONFIG_EZYNQ_MIO_PULLUP_EN_47

#define CONFIG_EZYNQ_MIO_PULLUP_DIS_0

#define CONFIG_EZYNQ_MIO_INOUT_47   OUT

#define CONFIG_EZYNQ_MIO_INOUT_47=   IN

#define CONFIG_EZYNQ_MIO_INOUT_47=   BIDIR

*/

#define CONFIG_EZYNQ_BOOT_USERDEF           0x1010000 /* # 0x1234567 # will be saved in the file header */

#define CONFIG_EZYNQ_BOOT_OCM_OFFSET        0xa40     /*  # 0x8C0   # start of OCM data relative to the flash image start >=0x8C0, 63-bytes aligned */

#define CONFIG_EZYNQ_BOOT_OCM_IMAGE_LENGTH  0x1400c   /*  # 0#0x30000 # number of bytes to load to the OCM memory, <=  0x30000 */

#define CONFIG_EZYNQ_START_EXEC             0x00      /*  # start of execution address */

#define CONFIG_EZYNQ_RESERVED44             0         /*  # documented as 0, but actually 1 */

#endif /* __CONFIG_EZYNQ_H */

 No newline at end of file